Use and Care Manual

eLEDing EE802WRC Quick Set-up Reference
Notes: Contact Info: [phone], [e-mail], www.eleding.com
Rev. EE802WRC 080415 Page 2
Specifications:
1. Solar Cell: 5V/440 mAH/2.2W
2. Li-ion Battery: 3.7V/2200mAH
3. Charging Time: < 6 hrs (1000 W/㎡)
4. Control distance: 20-30meters
5. Beam Angle: 120 Degrees
6. 53 LEDs: <5 W, <500 LM
9. LED Service Life: ＞50000 hrs
10. Light Color: Pure White/Warm White
11. Size:154*120*60.5 mm
First-Time Activate/Turn on the Light
The unit comes with an activation needle to activate the light. Insert the needle or
small paperclip into the small hole at the top edge of the light body to activate and
turn on the light (Refer Fig 1). If this process is launched in daylight condition the
unit will shut off automatically within a few seconds and then will turn on only in
darkness.
Mounting
Choose a flat and stable mounting surface with maximum exposure to direct
sunlight. It is essential that the panel receives 4 hours of direct sunlight every day in
order to ensure dusk to dawn performance. For Northern hemisphere installations
the light should be mounted with a southerly exposure and visa-versa for Southern
hemisphere installation. East and West mounting locations with good sun exposure
can also be good mounting locations.
Remote Control Instruction
1. Use master switch to turn on/off the light.
2. Use up and down button to adjust the brightness level
3. Use left and right button to change the light color from warm white to pure white
4. One remote control can control four group of lights in the same time by using
four block switches. For each group, there’s no limitation on light numbers. The
control’s effective range is 65-100 feet each.
Notes
Every EE802WRC comes with its own remote control. For multiple control bind
setting, users need to use every unit’s own remote control to clear the default setting
first, and use the master remote control to finish every unit’s bind setting.
Once the remote control is bound with multiple group of units, the brightness
button and light color button will be able to control all the units. If users want adjust
the brightness level or light color for only one group of unit, he or she should turn
off the other groups by using the block switches first.
The light will turn off automatically when the battery does not have enough
capacity due to insufficient direct sunlight. Thus, please install the light in a non-
obstructed position where it will receive 4 hours direct sunlight every day.
When dusk comes the unit will turn on in darkness when it senses a lower ambient
light level. When dawn comes the unit will automatically turn off when it senses an
increasing ambient light level. Activating the unit during nighttime or in dark
environment is recommended. For daytime setup and activation make sure the solar
panel surface is totally covered.
There are screw mounting marks on the light body to assist as mounting references
(Refer Fig 2). This light must be mounted horizontally in a higher position (up to
10’) to project light toward the desired area.
For wood surfaces, drill the screws into the pre-marked locations
For surfaces of concrete, brick or stucco, use a masonry bit to drill clearance holes
Insert the anchors and screws. Then mount the unit on the mounting screws.
Multiple Control Bind Settings
In default setting, the light is controlled by Block Switch 1. If users want use one
remote control to control more than one light, here are the steps:
1. Clear Default Setting
Turn off the light by using activation needle, wait for 10 seconds then turn on the
light by using the activation needle (long press for 2 seconds)
Press “ON” button (either Master Switch or the first Block Switch) for 5 times
within 3 seconds. If the indicator flash for 6 times, it shows the default setting has
been successfully cleared.
2. Binding Setting
Turn off the light by using activation needle, wait for 10 seconds then turn on
light by using the activation needle (long press for 2 seconds)
Quickly press the “ON” button on Block Switch 1,2,3,4 for one time. The
indicator will flash for 3 times, indicating the unit is bound with the remote control.