User's Manual Part 1
Table Of Contents
- Chapter 0 - Front Cover 195CM.doc
- Chapter 0 - Table of Contents 195CM.doc
- CHAPTER 1 – Introduction
- Before You Begin
- Model 195C/M Overview
- Three Configuration Phases
- Model 195C/M Hardware Description
- Modes of Operation Description and Examples
- Programming Examples
- CHAPTER 5 – Web Configuration
- Logging Into Web Configuration Manager
- Web Configuration Manager
- CHAPTER 6 – Serial Configuration and Applications
- Using USB Programming Port
- Using RS-232 Data Port
- ESTeem Mesh Network
- Rapid Spanning Tree Protocol (RSTP)
- Spanning Tree Protocols (STP)
- Redundant Backup
- CHAPTER 8 – Antenna Setups
- Antenna and Cable Configurations
- Weatherproofing Coaxial Cable Connections
- APPENDIX A – FCC Information
- APPENDIX B – Interface Ports
- APPENDIX C – Radio Configuration
- APPENDIX E – Troubleshooting
- APPENDIX F – 195C/M Specifications
- Before You Begin
- CHAPTER 1 – Introduction
- Chapter 1 - Introduction 195CM.doc
- BEFORE YOU BEGIN
- MODEL 195C/M OVERVIEW
- The ESTeem Model 195C/M and 195C/M are wireless modem transceivers that can be used to build many types of Wireless Local Area Networks (WLAN). The ESTeem 195C/M series have both and Ethernet interface and an RS-232 serial port for legacy device networks. The Model 195C/M is a very sophisticated networking device that can be configured for multiple modes of operation depending upon the needs of the wireless and wired LAN system. The following configuration modes are provided as an overview of the basic network types, as all possible network configurations can not be listed. For further help in selecting the correct network type, please refer to Chapter 4 of this User’s Manual or call Customer Support at 509-735-9092.
- CONFIGURATION MODES
- Chapter 2 - Starting Out 195CM.doc
- Chapter 3 - Example Applications 195CM.doc
- Chapter 4 - Utilities and Features 195CM.doc
- ESTeem Network Configuration Utility (ENC)
- Note: The ESTeem Resource Disk is a stand-alone copy of the ESTeem Web site (Figure 2). Navigation of the Resource Disk is as simple as using your web browser. All technical documentation, User’s Manuals and the ESTeem Utility Program are available on the disk.
- Note: If the page does not auto load, open your web browser and set your address line to D:\index.html (Where D: is the drive letter for your CD-ROM drive).
- Note: This program is saved in a compressed file format.
- Note: The SSID, Mode of Operation and Modem ID will be adjusted through the ENC Utility or the Web Configuration Manager...
- Note: The ESTeem Resource Disk is a stand-alone copy of the ESTeem Web site (Figure 1). Navigation of the Resource Disk is as simple as using your web browser. All technical documentation, User’s Manuals and the ESTeem Utility Program are available on the disk.
- Note: If the page does not auto load, open your web browser and set your address line to D:\index.html (Where D: is the drive letter for your CD-ROM drive).
- Note: This program is saved in a compressed file format. Microsoft Windows XP® will open the file directly, but other operating systems will require a common compression program such as WinZip available for download at http://www.winzip.com
- Note: This Utility will only operate with an ESTeem Model 195C/M in EtherStation mode.
- Chapter 5 - Serial Configuration and Applications 195CM.doc
- Chapter 6 - Repeating and Mesh Networking 195CM.doc
CHAPTER 4
UTILITIES & FEATURES
Note: This program is saved in a compressed file format.
3. Double click on the 195C/MDiscoverySetup<Current Version>.exe file listed in the window to install the program.
Figure 4: Discovery Program Main Page
4. Connect the Model 195C/M to your computer either directly to the Ethernet card or through a HUB/Switch using a CAT-5e
Ethernet cable. The Ethernet port on the 195C/M supports Auto-Negotiation, so either a patch cable or crossover cable will
work. Open the ESTeem Discovery Program and press the
Discover Modems button. The Model 195C/M will be displayed
in the program by the Ethernet MAC address and Current IP Address (Figure 4).
Note: The SSID, Mode of Operation and Modem ID will be adjusted through the ENC Utility or the Web Configuration
Manager...
5. Double-click on the 195C/M you want to program and the Configure IP Address window will be displayed (Figure 5). Enter
an IP address and Subnet Mask for the 195C/M that matches your network subnet and press the
OK button to save this to the
ESTeem. You will receive notification that the Configuration was Successful and the 195C/M will reboot.
Figure 5: Change IP Address Window
Revised: 1 Oct 13 4-3 EST P/N AA107-195CM