Datasheet

ManualsBrandsElectronic Assembly ManualsDisplaysLCD Backlight Amber 80 mA

Issue 8.2012

DOG SERIES 3.3V

INCL. CONTROLLER ST7036 FOR 4-/8-BIT, SPI (4-WIRE)

TECHNICAL DATA

* HIGH-CONTRAST LCD SUPERTWIST DISPLAY

* OPTIONAL LED BACKLIGHT UNITS IN DIFFERENT COLORS

* 1x8, 2x16 AND 3x16 WITH 12.0 mm / 5.6 mm AND 3.6 mm CHARACTER HEIGHT

* ST 7036 CONTROLLER FOR 4-BIT, 8-BIT AND SPI (4-WIRE) INTERFACE

* POWER SUPPLY +3.3V OR +5V SINGLE SUPPLY (typically 250µA)

* NO ADDITIONAL VOLTAGES REQUIRED

* OPERATING TEMPERATURE RANGE -20 THROUGH +70°C

* LED BACKLIGHT 3 through 80mA@3.3V or 2 through 40mA@5V

* NO MOUNTING REQUIRED, SIMPLY SOLDER INTO PCB

ORDERING CODE

LCD MODULE 1x8 - 11.97mm EA DOGM081x-A

LCD MODULE 2x16 - 5.57 mm EA DOGM162x-A

LCD MODULE 3x16 - 3.65mm EA DOGM163x-A

x: B = blue background

E = yellow/green background

L = yellow/green background (cannot be backlit)

S = black background

W = white background

LED BACKLIGHT, WHITE EA LED55X31-W

LED BACKLIGHT, YELLOW/GREEN EA LED55X31-G

LED BACKLIGHT, BLUE EA LED55X31-B

LED BACKLIGHT, RED EA LED55X31-R

LED BACKLIGHT, AMBER EA LED55X31-A

LED BACKLIGHT, FULL COLOR RGB EA LED55X31-RGB

USB TEST BOARD FOR PC (WINDOWS) EA 9780-2USB

SOCKET CONNECTOR 4.8 mm HIGH (1x20-PIN, 2.54mm PITCH) EA FL-20P

EA LED55x31-W

white

EA DOGM163B-A

blue

available for 1 pc. off !

even with LED: 5.8mm flat

EA DOGM081S-A

+ EA LED55x31-W

EA DOGM162E-A

+ EA LED55x31-G

EA DOGM163W-A

+ EA LED55x31-W

EA DOGM162W-A

+ EA LED55x31-A

EA DOGM081W-A

+ EA LED55x31-B

Summary of content (8 pages)

PAGE 1
Issue 8.2012 DOG SERIES 3.3V INCL. CONTROLLER ST7036 FOR 4-/8-BIT, SPI (4-WIRE) EA DOGM163B-A blue off ! . c p t for 1 .8mm fla e l b a 5 avail th LED: wi EA DOGM081S-A even EA LED55x31-W white + EA LED55x31-W EA DOGM162E-A + EA LED55x31-G EA DOGM163W-A + EA LED55x31-W EA DOGM081W-A + EA LED55x31-B EA DOGM162W-A + EA LED55x31-A TECHNICAL DATA * * * * * * * * * HIGH-CONTRAST LCD SUPERTWIST DISPLAY OPTIONAL LED BACKLIGHT UNITS IN DIFFERENT COLORS 1x8, 2x16 AND 3x16 WITH 12.0 mm / 5.6 mm AND 3.
PAGE 2
EA DOG-M EA DOG SERIES With its EA DOG series, ELECTRONIC ASSEMBLY presents the world’s first display series which will run on 3.3 V systems without auxiliary power. They can, of course be used on traditional 5 V systems. Unlike normal LCD modules, you order the display and the corresponding backlight separately. This gives you a wealth of possible combinations.
PAGE 3
EA DOG-M 5 DIFFERENT TECHNOLOGIES As a standard we provide 5 different technologies as STN and FSTN: display type technology optional backlight readability display color non backlighted display color recommended with backlight color backlighted FSTN pos. transflective it's fine with and without backlight readable even without backlight black on white black on backlight color white, blue, RGB STN pos.
PAGE 4
EA DOG-M APPLICATION EXAMPLES Different wiring must be used depending on the interface and the power supply. 2 additional capacitors are required for 3.3 V operation. Note that the COG technology means that the current capacity of the outputs is limited. Therefore, a large load on the bus may cause signal loops and unclean levels. If in doubt, additional pull-down resistors (8051) are required or additional waits/NOPs must be incorporated.
PAGE 5
EA DOG-M CHARACTER SET The below show character set is already built-in. In addition to that you are able to define 8 characters by your own. A detailed description for integrated controller http://www.lcd-module.de/eng/pdf/zubehoer/st7036.pdf Printing and typographical errors reserved. ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice.
PAGE 6
EA DOG-M A detailed description for integrated controller ST7036 you can find under http://www.lcd-module.de/eng/pdf/zubehoer/st7036.pdf TABLE OF COMMAND Page 6 Printing and typographical errors reserved. ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice.
PAGE 7
EA DOG-M EXAMPLES FOR INITIALISATION EA DOGM081 Example of initialisation: 8 bit / 3.
PAGE 8
ELECTRONIC ASSEMBLY GmbH Zeppelinstraße 19 D-82205 Gilching Germany Fon: Fax: e-Mail: Web: +49 (0)8105-77 80 90 +49 (0)8105-77 80 99 info@lcd-module.de www.lcd-module.com Note: The 4 LED pins A1, C1, A2 and C2 (or A, R, G, B) must be soldered from the top to ensure a clean contact.