«] Electrolyte Upright Vacuum Cleaner Models 21373, Z1376, Z1379 21488, Z1498 I Index Important Safeguards Service Information Assembly Thermal Cut Off =4 Accessories. Cyclonic Cassette . Brush ROFL Brush Roil Belt . 12 Hose Blockage 13 Filters 14 HEAP Filter ..
IMPORTANT USER INFORMATION 1T IS MOST IMPORTANT THAT THIS INSTRUCTION BOOK SHOULD BE RETAINED WITH THE APPLIANCE FOR FUTURE REFERENCE. SHOULD THE APPLIANCE BE SOLD OR TRANSFERRED TO ANOTHER OWNER, OR SHOULD YOU MOVE HOUSE AND LEAVE THE APPLIANCE, ALWAYS ENSURE THAT THE BOOK IS SUPPLIED WITH THE APPLIANCE IN ORDER THAT THE NEW OWNER CAN BE ACQUAINTED WITH THE FUNCTIONING OF THE APPLIANCE AND THE RELEVANT WARNINGS. THESE WARNINGS ARE PROVIDED IN THE INTEREST OF SAFETY.
BEFORE YOU START CHECK THE VOLTAGE First check the voltage shown on the data plate {see rear view) to make sure that the cleaner is of the correct voltage for your electricity supply. If it is not, do not use the cleaner but refer back to your dealer. CONNECTING TO YOUR ELECTRICITY SUPPLY Permanently connected to the cleaner is a mains supply (2-core) cable fitted with a non-rewindable plug incorporating a 13A fuse.
SERVICE Should you require service on your Electrolyte cleaner, please telephone 08706 055055. Before requesting service, please check whether your problem is covered under Service Checklist (see below). New filter pads, brush rollers and drive baits can be obtained from Electrolyte Dealers. If difficulty is experienced in obtaining spares, please contact 08706 055055. SERVICE CHECKLIST « If your cleaner will not operate, check the plug connection, plug fuse and mains fuse.
HOW TO ASSEMBLE CAUTION: Assemble the cleaner before using. NOTE: Features may vary by model yet all parts assemble in the same way. Step A Attach Hose IMPORTANT: Hose MUST BE inserted before attaching the handle. 1. Locate the tab on the hose adapter of the extension hose {shortest end}. 2. Insert hose adapter into opening on top of unit. The hose adapter tab must be placed all the way down into the notch, Step B Attach Handle CAUTION: Do not catch cord under handle. 3. 5.
N v Combination | Tool \ | Crevice Tool Extension DN Wand or S SRR Wands Hose Z Retainer Hook Carrying Handle Step D Store Electrical Cord Step E Check Cyclonic Cassette Make sure that the cyclonic cassette is fully seated in the vacuum, Place thumbs on cyclonic cassette {marked by arrows above) and push firmly until it clicks home. NOTE: Do not lift cleaner by cassette handle, use carrying handle on the back of cleaner. See illustration in Step C.
HOW TO USE The upright vacuum cleaner design allows use on multiple types of carpeting and on upholstery or bare floors with attachments. When using the attachment tools, place the handier in the upright position. Do not place cleaner on furniture or steps as the brush roll may cause damage. 1. Adjust cleaner height setting knob to lowest position for maximum cleaning. Adjust to a higher setting to make pushing easier. For easy adjustments, tilt the cleaner back to move the knob.
SUPER STRETCH HOSE (Only available on StairMaster models.) The super stretch hose has a new added feature. A hose strap has been added to the super stretch hose for ease of use while cleaning with the attachments, By hooking the hose strap into the strap hook before using your attachments, you will improve the mobility of your vacuum when extending the super stretch hose to its maximum reach (except Z1373). TO HOOK HOSE STRAP (A) ONTO STRAP UPPER HOSE HOOK (B), START AT STEP 1 RETAINER 1.
How To Use Accessories Crevice tool cleans corners, baseboards, NOTE: Do not place cleaner on furniture or between cushions. steps as the brush roll may cause damage. Place cleaner on floor with Q the handier in storage position while using accessories. ./ 1. Remove hose from rear of cleaner. Crevice Tool Combination tool gives two types of cleaning tools: * Use brush side to dust furniture, blinds, books, damps, shelves. * Use upholstery side for curtains, draperies, cushions, fabrics.
HOW TO MAINTAIN The instructions in this booklet serve as a guide to routine maintenance. To avoid unnecessary service calls, check the cyclonic cassette, belt, and brush roll often. To Change Cassette Micron Filter: NOTE: Turn off the switch and unplug the electrical cord before changing the Cassette Micron Filter. Never operate the vacuum cleaner without the cyclonic cassette or the filter.
HOW TO MAINTAIN (continued) How To Empty Cyclonic Cassette NOTE: Turn off the switch and unplug the electrical cord before emptying cyclonic cassette. Never operate the vacuum cleaner without the cyclonic cassette or the filter. FOR INSTRUCTIONS ON HOW TO REMOVE THE CYCLONIC CASSETTE FROM THE CASSETTE BODY, REFER TO PAGE 10. Emptying the Cyclonic Cassette Iris clearly visible when the dust compartment is full and needs emptying.
HOW TO MAINTAIN (continued) Brush Roll The brush roll turns as it sweeps and combs the carpet nap. Remove hair and threads from the brush roll so it continues brushing the carpet. To maintain the most efficient cleaning, the bristles must touch the carpet. To test the bristle length, hold a ruler against the underneath side of the cleaner. If the bristles no longer touch the ruler, replace the brush roll. Brush Roll Belt The brush roll belt tums the brush roll to agitate, sweep, and comb the carpet nap.
HOW TO MAINTAIN (continued) How to Clear Hose Blockage Note: Turn off the switch and unplug the electrical 8. Flexing the hose may help loosen the clog. cord before clearing hose. Step on handle release. Lower handier until cleaner is flat on the floor. /’ 1 Turn the cleaner over so back side faces up Lift cleaner and rest it against a support or counter. Ult the end of the hose from the hose retainer. Check for blockage in the hose retainer and the hose assembly, 7.
HOW TO MAINTAIN (continued) Motor Filter Check the motor filter each time the cyclonic cassette is emptied. Clean or replace as needed. To Clean Motor Filter 1. Remove filter from inside cassette compartment, lower left side. 2. Shake filter to remove excess dust. If necessary, rinse the filter under warm running water. 3. Reinstall filter when completely dry. Use GENUINE ELECTROLYTE replacement motor filter. Call Electrolytic on 08706 055055 for assistance.
PROBLEM SOLVING NOTE: Turn off the switch and unplug the electrical cord before servicing. PROBLEM CAUSE SOLUTION Motor will not start. VI Electric Plug [ push plug securely into outlet. [ Try another outlet [ Check circuit breaker. Motor suddenly stops. Y Thermal Cut Ot L3 Refer to page 7. Does not clean the carpet or floor, Z Liters ¥ Cyclonic Cassette ¥ Belt W Bewitch V! Brush Roll V' Hose O Eleanor replace the filter(s).
[ Electrolyte MAIL ORDER FORM Should you experience difficulty in obtaining original spares from your local stockist, may we suggest that you make use of this order form, Please fill in following details Name: e Model No: Address: oo Product No: Postcode: IMPORTANT, be sure to include your Model and Product numbers. These numbers may be found on your rating plate.
Guarantee This guarantee is in addition to your statutory and other legal rights. Electrolyte products are carefully designed, manufactured, tested and inspected and, in consequence, we undertake to replace or repair any part found to be defective in material or workmanship, within one year of delivery to the original purchaser, free of charge. There are certain conditions which may invalidate this guarantee: a.
Questions? Call 08706 055055 Accessory stems in This Carton 9 1 crevice tool 1 wand = & 1 hose assembly 1 hardware package ! (2 screws) 1 vacuum cleaner handle Thank you for selecting an Electrolyte cleaner. Don’t Forget to Use Genuine Electrolyte Belts and Filters Part No. 59983A wen Printed in US.A.
