Programming Manual Washer Extractors Compass Control 438 9216-01/EN 07.
Contents Contents Safety precautions......................................................................................5 General........................................................................................................7 Engaging servicemode...........................................................................7 Programming...............................................................................................9 Parameter programming................................................
Safety Precautions Safety Precautions This machine can only be used with water. Never use dry cleaning agents. Do not allow children to operate the machine. Do not hose down or spray the machine with water. All mechanical and electrical installation must be carried out by qualified personnel. Do not bypass the door locking device. Should the machine malfunction, please report the fault to the technician responsible for the machine.
General General This programming manual is intended for personnel with the authority to adjust parameters in the machine’s existing wash programs, programming slot meters, reading statistics and configuring certain machine interfaces with the user. Programming is achieved using menus in the display while the machine is in service mode. Engaging servicemode 1 Alt. 1 Service mode is engaged by using one of the following alternative: CON6 1 1 Alt.
General 2 The machine software will now switch to its service mode. The display lists the submenus available in this mode. 2 MAIN MENU 01.00.00.00 SERVICE PARAMETER PROG STATISTICS CONFIG 1 CONFIG 2 This programming manual describes the functions and programming instructions for the following submenus: • • • • • PARAMETER PROGR. STATISTICS ADJUST DISPLAY RESET TO FACTORY QUICK START BUTTONS For other submenus, please refer to the service manual.
Programming Programming 1 Parameter programming MAIN MENU 02.00.00.00 SERVICE PARAMETER PROG STATISTICS CONFIG 1 CONFIG 2 ADJUST DISPLAY From this menu you can change a number of parameters in the machine’s wash program. These changes can be applied to all installed wash programs or just for one individual wash program. 1 2 3 4 Select the PARAMETER PROG row and press the knob. Choose whether to apply the change to all the wash programs or just to one individual wash program and press the knob.
5 Programming The arrow in each parameter menu shows the column being adjusted. 5 • Turn the knob clockwise to set the desired number between 0 and 9. PARAMETER PROGR. add prerinses • Turn the knob anticlockwise to move to the next column. Turn the knob clockwise and set the value, etc. 000 • Once all the columns have been set, press the knob to confirm the setting. Save by selection YES. • Once all the necessary parameters have been adjusted, select EXIT to return to the main menu.
Programming ADD PRERINSES 6 Use the knob to set the number of rinses to be added to all or the chosen wash program and press the knob. 11 6 PARAMETER PROGR. add prerinses 000 Confirm that the setting is to be saved by selecting yes and pressing the knob again. TIME PREWASHES 7 Use the knob to adjust the time for the prewash to be applied to all or the chosen wash program and press the knob. The time is given in minutes ± 20. (In some cases the value is limited.
Programming 12 TIME MAIN WASHES 10 Use the knob to adjust the time for the main wash to be applied to all or the chosen wash program and press the knob. The time is given in minutes ± 20. (In some cases the value is limited. If a too high value is selected, the display will show the max value allowed.) 10 PARAMETER PROGR. MAIN WASH minuteS +0000 Confirm that the setting is to be saved by selecting yes and pressing the knob again.
Programming LEVEL RINSES 14 13 14 Use the knob to adjust the water level for rinses to be applied to all or the chosen wash program and press the knob. The level is given in scale divisions±78, see under heading "Conversion table water level". (In some cases the value is limited. If a too high value is selected, the display will show the max value allowed.) PARAMETER PROGR. level rinses +0000 Confirm that the setting is to be saved by selecting yes and pressing the knob again. SKIP SEC.
Programming 14 Statistics 16 17 This menu contains statistics on running time, completed wash programs and terminated wash programs, slot meter and error codes. Select the STATISTICS row and press the knob. The display will now show a number of submenus containing the available statistics. Select the desired menu and press the knob. • • • • • • • • • • • • • • • • RUN HOURS TRIP RUN HOURS RESET TRIP RUN HOURS NUMB. WASH PROG. TRIP. WASH PROG. RESET WASH PROG.
Programming NUMB. WASH PROG. 21 21 Specifies the total number of wash programs since the machine was installed and used for the first time. TRIP. WASH PROG. 22 15 Specifies the total number of wash programs since the counter was last reset. STATISTICS NUMB. WASH PROG. 00000 BACK=PRESS KNOB RESET WASH PROG. Resets the wash program trip counter. 23 22 Confirm that the counter is to be reset by selecting yes and pressing the knob again.
Programming 16 OMITTED EXTRACTIONS 26 Specifies the number of times the machine has omitted water extraction due to an unbalanced drum. ERROR LOG 1 27 28 26 Shows up to 20 of the latest error codes and how many wash programs that have been carried out since the error code was generated. The most recent error is at the top of the list. Select an error code and press the knob.
Programming ERROR LOG MOTOR 31 The internal registration of error codes in the motor control is shown. 17 31 READING MCU E2PRO Note! It can take up to one minute before information is shown in the display. For further information, contact your supplier. WASH PROG. STATISTICS 32 33 Shows a list of the wash programs installed on the machine. Select a wash program and press the knob. The following information is given for the selected error code: 6204 32 WASH PROG. STATISTICS 03.14.01.
Programming 18 ADJUST DISPLAY 34 35 The contrast of the display can be adjusted with this menu to adapt to the prevailing lighting in the room where the machine is placed. Turn clockwise or counter clockwise direction. Adjust the value as necessary. Confirm the new setting by selecting yes and pressing the knob again. 34 MAIN MENU 06.00.00.00 CONFIG 2 ADJUST DISPLAY RESET TO FACTORY ACTIVATE WASH PROGR.
Programming QUICK START BUTTONS This menu enables you to program the machine’s quick start buttons (applies to quick start buttons marked 1 and 2 only). 39 Select the QUICK START BUTTONS/CONFIG BUTTONS row and press the knob. 40 Press the button to be programmed. 41 19 39 MAIN MENU 09.00.00.00 ADJUST DISPLAY RESET TO FACTORY ACTIVATE WASH PROG. QUICK START BUTTONS I/O ADDRESS EXIT Select a program, option or disable the button. To be able to select an option, a wash program has to be selected first.
Price programming Price programming 21 1 To be able to perform price programming the machine needs to have the coin-meter installed and connected. If a machine is equipped with a coin-meter after it has been installed, the coin-meter needs to be activated prior to price settings. This can be done by setting a value on Coin Value 1 alt. both Coin Value 1 and 2. This can be done under the menu Config 1 or under Price Programming.
Price programming 22 Price on option 5 • Mark row “Price on option” and press the knob. 6 • Select the option for price setting. 7 • Give requested price and press the knob. 5 PRICE PROGRAMMING 11.02.01.00AM PRICE ON PROGRAM PRICE ON OPTION PRICE REDUCTION COIN VALUE SHOW COIN COUNTER EXIT Price set option will be shown with a rectangle after the option name. Price reduction 8 9 6204 6 • Mark row “Price reduction” and press the knob.
Price programming Coin value The ”Coin Value” menu is used to specify the relationship between coin slot 1 and coin slot 2. 10 Select the COIN VALUE row and press the knob. 11 Select COIN VALUE 1 or 2 and press the knob. For coin counters with one coin slot, only Coin Value 1 is used. 12 10 PRICE PROGRAMMING 11.04.00.00AM PRICE REDUCTION COIN VALUE SHOW COIN COUNTER EXIT Enter the desired value (0 999) for each coin slot.
Price programming 24 Show coin counter 14 The "Show coin counter" is used to show the value for the counters 1 and 2 since last reset. 14 Select the SHOW COIN COUNTER row and press the knob. 15 Coin count 1 shows the total sum of the value of the coins inserted in coin insert 1 alt. 1 and 2. PRICE PROGRAMMINGAM COIN VALUE SHOW COIN COUNTER EXIT Coin count 2 shows the total number of the coins inserted in coin insert 1 alt. 1 and 2.
Conversion table water level with empty drum Conversion table water level with empty drum W455H Scale unit Water volume (litre) Water level * (mm) 19 2 9 Empty level 34 3 19 Heating level 76 6.9 50 95 8.8 64 102 9.6 69 116 11.1 79 124 12 85 132 13 91 150 15.1 104 320 36.3 225 350 41.5 248 Low level Medium level High level Over filling level * Level above bottom of inner drum W465H Scale unit Water volume (litre) Water level * (mm) 42 2.9 1 Empty level 50 3.
Conversion table water level with empty drum 26 W475H, EX618 Scale unit Water volume (litre) Water level * (mm) 45 2.8 1 Empty level 50 3.2 5 Heating level 82 5.8 30 100 7.5 43 129 10.9 65 150 13.5 82 159 14.6 89 170 15.9 96 195 19.5 116 270 30 170 480 59.2 323 Low level Medium level High level Over filling level * Level above bottom of inner drum W4105H, EX625 Scale unit Water volume (litre) Water level * (mm) 50 3.5 1 Empty level 60 4.
Conversion table water level with empty drum W4130H, EX630, WD4130H Scale unit Water volume (litre) Water level * (mm) 49 4.9 1 Empty level 52 5.9 10 Heating level 79 8.8 30 150 18.9 83 190 25.3 112 235 33.2 145 239 34 148 255 36.8 160 290 43 185 660 112 453 Low level Medium level High level Over filling level * Level above bottom of inner drum W4180H, EX640 Scale unit Water volume (litre) Water level * (mm) 45 5.9 1 Empty level 60 7.
Conversion table water level with empty drum 28 W4300H, EX670 Scale unit Water volume (litre) Water level * (mm) 49 7.3 1 Empty level 60 9.7 10 Heating level 152 29.9 76 250 59 145 297 75 1179 330 86.4 203 350 93.4 218 360 96.9 225 400 111 255 730 234 495 Low level Medium level High level Over filling level * Level above bottom of inner drum W475M, W475N Scale unit Water volume (litre) Water level * (mm) 45 2.8 1 Empty level 50 3.2 5 Heating level 95 7.
Conversion table water level with empty drum W4105M, W4105N Scale unit Water volume (litre) Water level * (mm) 50 3.5 1 Empty level 60 4.6 12 Heating level 100 9.1 45 160 16.9 89 194 21.4 113 245 29.1 150 249 29.7 153 260 31.4 161 280 34.6 175 520 73 348 Low level Medium level High level Over filling level * Level above bottom of inner drum W4130M, W4130N, SU630, W630 Scale unit Water volume (litre) Water level * (mm) 52 4.2 1 Empty level 60 5.
Conversion table water level with empty drum 30 W4250M, W4250N, SU655, W655 Scale unit Water volume (litre) Water level * (mm) 44 6.6 1 Empty level 60 8.9 14 Heating level 250 54.1 151 Low level 270 60 166 340 81.2 216 Medium level 380 93.8 245 High level 385 95.3 249 740 211 508 Over filling level * Level above bottom of inner drum W4330M, W4330N, SU675, W675 Scale unit Water volume (litre) Water level * (mm) 54 8.2 1 Empty level 60 9.
www.electrolux.com/professional Share more of our thinking at www.electrolux.