PowerFridge RC3000 0402 Operating Instructions 207.5044.
Please read these operating instructions carefully before putting the refrigeration unit into operation. If you later sell or dispose of it, please ensure that the new owner receives these operating instructions. Thank you for choosing our appliance. We are sure it will provide you with trouble-free use.
CONTENT S 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Unpacking View of the appliance Cleaning Positioning the appliance Using the appliance 5.1. From electrical mains 5.2. From vehicle battery 5.3. From bottled gas Mounting the wheels Making ice Useful suggestions Defrosting, cleaning and maintenance Customer service Putting into operation, technical data 11.1. Connecting to electrical mains 11.2. Connecting to vehicle power supply 11.3. Connecting to bottled gas cylinder 11.4.
1. Unpacking After removal from the cardboard packaging, make sure the appliance is not damaged. If you find damage to the appliance resulting from transport, report it immediately to the transportation firm. 2. View of the appliance Figure 1. 1. insulated casing 6. rear cover 2. insulated lid 7. ice tray 3. handle 8. ice-tray shelf 4. control panel 9. wheels 5.
3. Cleaning Clean both the inside and outside of the appliance before putting it into use. To do so, use a soft towel, lukewarm water and a non-abrasive detergent. Ensure water does not enter the rear cover grille or the control elements. Afterwards, wipe the appliance with a clean towel and cleanwater, and then wipe it dry. To avoid damage, do not use soap, soda or abrasive cleaners. 4.
5.2. Operating from vehicle battery Make sure the voltage shown on the data plate of the appliance matches the voltage of the vehicle battery (12V or 24V). 12V DC voltage appliances are equipped with connectors that can be plugged into cigarette lighters (Figure 3.). For some types of vehicle, you may need to remove the red plastic ring located on the end of the connector. To do so, turn the plastic ring in an anticlockwise direction and pull it off.
First mount the two wheels on the axle. To do so, press in the spring located on the wheel (Figure 6); then release the spring, pushing the wheel onto the axle. It can be felt when the spring jumps into place and it is not possible to pull the wheel from the axle. Figure 6. After mounting the wheels, fasten the axle to the bottom of the housing. To do so, turn the appliance upside down (while empty) and fasten the axle with the retaining screw (Figure 7). Figure 7.
7. Making ice The ice-tray holder and ice-tray accessories delivered with the appliance allow ice cubes to be made. To do so, first insert the ice-tray holder panel into the groove of the plastic holder. Make sure the perforated part of the panel enters the groove (Figure 9). Next, fill the ice tray with water (up to about 4 mm below the edge) and put on the cover. Figure 9. Place the ice tray on the ice-tray holder panel, so that its outer edge is below the edge of the plastic cover (Figure 10).
10.
11.2 Connecting to vehicle power source Make sure no other energy source is connected (gas, 230V). 12V appliances must be connected to a vehicle cigarette lighter, which is protected with a 10A fuse. 24V appliances must be connected by inserting a terminal block and switch and protected with a 5A fuse. The switch must be suitable for switching a 5A current. 11.3 Connecting to gas cylinder Make sure no other energy source is connected (230V, 12V).
Figure 11. For your safety: Do not check for leaks with a naked flame! Do not smoke while checking for leaks! 12. Environmental protection information The appliance does not contain any CFCs/HCFCs. Ammonia (natural hydrogen and nitrogen compound) is used as a refrigerating agent in the refrigeration unit. The ozone-friendly cyclopentane is activated as a motive agent for the PU foam insulation. Sodium chromate is used for corrosion protection (less than 2 weight % of the coolant). 13.
Printed by Xerox Hungary Ltd. Rev.: 2003. 09. 03.
