G e s c h i r r s p ü l e r D i s h w a s h e r Model ESF 6132 D GB Bedienungsanleitung Instruction book Seite 2 page 19
Contents Safety instructions 20 Disposal 20 Economical and ecological dishwashing 20 Installation instructions Fitting under a counter Levelling Water supply connections Water outlet hose connection Electrical connection 21 21 21 21 22 22 Description of the appliance 23 The control panel 23 Prior to using for the first time Setting the water softener Filling with salt Rinse aid 24 24 25 26 In daily use Loading cutlery and dishes The lower basket The cutlery basket The upper basket Adjusting th
Safety instructions It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information. This information has been provided in the interest of your safety.
Installation instructions Any electrical and/or plumbing work required to install this appliance should be carried out by a qualified electrician and/or plumber or competent person. Water supply connections This dishwasher may be fed with either hot (max. 60°) or cold water. Nevertheless we advise you a cold water supply. A hot water supply is not always efficient with very soiled crockery as it shortens the washing programmes a lot. Remove all packaging before positioning the machine.
Water outlet hose connection Electrical connection The end of the drain hose can be connected in the following ways: Information concerning the electrical connection is given on the rating plate on the edge of the dishwasher’s door. 1. To the sink outlet spigot, securing it to the underside of the work surface. This will prevent waste water from the sink running into the machine. Before plugging the appliance into the wall socket, make sure that: 1.
Description of the appliance 1. Upper basket stop 2. Water hardness switch 3. Salt container 4. Detergent dispenser 5. Control panel 6. Rating plate 7. Rinse aid dispenser 8. Filters 9. Lower spray arm 10. Upper spray arm 11. Upper basket 12.
Prior to using for the first time Before using your dishwasher for the first time: b) Setting electronically (The dishwasher must be switched off) 1. Ensure that the electrical and water connections comply with the installation instructions The dishwasher is factory set at level 5. 2. Remove all packaging from inside the appliance 1. Press the On/Off push button. The On/Off indicator light illuminates (setting mode).
Filling with salt Only use salt specifically designed for use in dishwashers. All other types of salt not specifically designed for use in a dishwasher, especially table salt, will damage the water softener. Only fill with salt just before starting one of the complete washing programmes. This will prevent any grains of salt or salty water, which may have been spilt, remaining on the bottom of the machine for any period of time, which may cause corrosion. To fill: 1.
Rinse aid ● Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying. The dispenser, which is positioned inside the door, holds about 110 ml of rinse aid, which is sufficient for 16 - 40 dishwashing programmes, depending upon the dosage setting. If you are using dishwasher detergent that already contains rinse aid, it is necessary to deactivate the inflow of rinse aid, in order to avoid a double dosage.
In daily use ● Check if it’s necessary to refill with special salt or rinse aid Loading cutlery and dishes ● Load cutlery and dishes into the dishwasher. ● Fill with dishwasher detergent . Sponges, household cloths and any object that can absorb water may not be washed in the dishwasher. ● Select a wash programme suitable for the cutlery and dishes. ● Start the wash programme. ● Before loading the dishes, you should: - Remove large left-overs.
The cutlery basket Adjusting the height of the upper basket Long bladed knives stored in an upright position are a potential hazard. Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket. Take care when loading or unloading sharp items such as knives. If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position.
Fill with detergent Use of detergent 1. If the lid is closed: press release button (1). The lid springs open. Only use detergents specifically designed for use in dishwashers. 2. Fill the detergent dispenser (2) with detergent. The marking indicates the dosing levels: 20 = approximately 20 g of detergent 30 = approximately 30 g of detergent Using no more then the correct amount of detergent contributes to reducing pollution.
Washing programmes Programme Intensive 70°C Normal 65°C (1) Quick 60°C (2) Bio 50°C Rinse and Hold Degree of soil and type of load Heavy soil. Crockery, cutlery, pots and pans Normal soil. Crockery and cutlery Fresh soil. Crockery and cutlery Normal soil. Crockery and cutlery Any. Partial load (to be completed later in the day).
Starting a washing programme To interrupt a washing programme in progress 1. Check that the baskets have been loaded correctly and that the spray arms can rotate freely a) Open the dishwasher door; the programme will stop. Close the door; the programme will start from the point in which it was interrupted. b) Press the On/Off push button (in this case all the indicator lights turn off). Press the On/Off push button again; the programme will start from the point in which it was interrupted. 2.
Maintenance and cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth. If necessary use only neutral detergents. Never use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc....). Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned regularly with a damp cloth. We recommend every 3 months to run a 65°C wash programme without dishes using detergent.
What to do, when... Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the instructions given here, without calling out an engineer. ...a flashing fault code appears The dishwasher will not start or stops during operation. All push buttons are inoperative except for the On/Off push button and a combination of indicator lights, as indicated in the following chart, are flashing.
...the wash results are not satisfactory The dishes are not clean ● ● ● ● ● ● ● ● The wrong washing programme has been selected. The dishes were arranged in such a way as to stop water reaching all parts of the surface. The baskets must not be overloaded. The spray arms do not rotate freely due to wrong arrangement of the load. The filters in the base of the washing compartment are dirty or incorrectly positioned. Too little or no detergent has been used.
Hints for test centres Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme (see "Washing programmes" chart). Test in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme (see "Washing programmes" chart).
The Electrolux Group. The world’s No.1 choice. The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. 14 billion USD in more than 150 countries around the world.
