EQAXF01BXWT EN USER MANUAL 1
Welcome Thank you for choosing ELECTROLUX. This manual contains all the information you need to safely and correctly use your water dispenser. Please read all the instructions prior to using the appliance, and keep this manual in a secure place for future reference. Do not remove the rating plate label which attached adhesive identification label containing the code, model number, manufacturer and other information.
Contents Water dispenser information ......................................................... 3 Precautions ................................................................................. 4 Illustration ................................................................................... 6 Using your water dispenser ........................................................... 7 Operation instructions ....................................................................... 8 Cleaning and maintenance .........
Water dispenser information 1. This unit is designed for drinkable water only. Put bottles as specified inside the cabinet before using. 2. This unit should be used in an environment with temperatures ranging from 10°C to 43°C with a relative humidity not higher than 90%. 3. The dispenser can satisfy the need for hot water, cold water, room temperature water and water as a mixture of the cold water and room temperature water. 4.
Precautions For children 1. Destroy the carton, plastic bag and other packing materials after the dispenser is unpacked. Children might use them for play. 2. Children require supervision when using the dispenser. 3. Recommend to install the anti-tilt bracket at the back side of this water dispenser to prevent the dispenser from falling down which could cause injury.(Fig. 6) For the user/installer 1. Plug the water dispenser directly into the socket.
7. Do not pull out or insert the plug with wet hands to avoid electric shock.(Fig. 3) 8. Use the switch when turning the heating/ cooling On/Off. Locate on the left back side of water dispenser.(page 6) 9. Do not fasten, twist or tie the power cord. if the power cord is damaged, it should be replaced by the manufacturer, service technician or a qualified person to prevent any risk. Fig. 3 10. Keep the unit in a dry place and away from direct sunlight. Do not place the machine on paper or foam.
Illustration 9 10 11 8 4 5 6 7 12 13 (FRONT) (REAR) indicator light cooling switch heating switch power cord button of hot water button of normal water button of cold water panel spout front carapace drain hole 13 condenser drip tray 6
Using your water dispenser Locate dispenser 1. Place dispenser upright. 2. Locate dispenser on a hard and level surface in a cool shaded location near a grounded socket. Do not plug in power cord yet. 3. Position dispenser so the back is at least 20 cm from wall and there are at least 20 cm of clearance on both sides. Assemble 1. Snap drip tray and grid assembly into front carapace. Machine Installation Installing the floor Bracket kit(Fig.6) 1.
Provide electricity Plug cord into a properly grounded socket. At this time the pump will begin to move water from the bottle to the hot and cold tanks. It will take up to approximate 5 minutes to fill the tanks for the first time. During this period the pump will run continuously. This is normal. Fig. 8 Operation Instructions Light indicators The indicator lights show that the device is working correctly. After connecting the device, check if the indicators are on. Lights up when water shortage.
Dispensing cold water After setup, it will take up to approximate 1 hour get water to maximum cold temperature. During this time the compressor could run continuously. This is normal. 1. Position bottle, glass, pitcher or cooking pot below spout. 2. Press cold water button downward to start cold water flow. 3. Release button once desired fill level is achieved. Fig.10 Dispensing normal water 1. Position bottle, glass, pitcher or cooking pot below spout. 2.
Changing bottles A flashing orange light on your function lights alerts you when your bottle is empty. Replace the bottle as soon as possible. Do not dispense hot, cool or cold water if the orange light is flashing as you could empty the tanks and cause the dispenser to overheat. 1. Open the cabinet door. 2. Slide empty bottle out of cabinet. Fig.12 3. Remove probe assembly from empty bottle. 4. Set empty bottle aside. 5. Place fresh bottle outside of cabinet. Remove entire plastic cap from top of bottle.
Sanitizing The machine should be disinfected with disinfectant separately bought from drugstore or marketplace according to the instruction manual of the disinfectant and then clean it with water (see cleaning and draining instructions). Generally this should be done every three months. Fig.
Trouble Shooting Before calling your service representative check the following items: Water dispenser does not work • Make sure the water dispenser is properly connected to a working socket and the heating/cooling switches are set ON. Water is leaking • Unplug the water dispenser, remove bottle and replace with new one. • Make sure the drain cap at the back side of water dispenser is tighten enough. No water is coming from the spout • Make sure the bottle is not empty, if empty, replace it with new one.
Circuit diagram LED2 LED3 LED4 CON1 CON2 CON4 CON6 EARTH2 EARTH L_HEATER1 PUM KEY1 L_HEATER2 Hot Thermostat 1 N_HEATER1 FLOAT N_HEATER2 KEY2 Hot Thermostat 2 HEATER GND GND Technical Information Model Power supply Cooling Power Heating Power Hot Water EQAXF01BXWT 220 -240V~ 50/60Hz 100W 420W 4L/h(≥90°C) Cold Water Room Temperature Operation Relative Humidity 2L/h(≤10°C) 10-43°C ≤90% Cooling Current Refrigerant Climate Class Cooling Cabinet Temperature 1.
Customer Care Thailand Call Center Tel : (+66 2) 725 9000 Electrolux Thailand Co.,Ltd. Electrolux Building 14th Floor 1910 New Petchburi Road, Bangkapi,Huay Kwang, Bangkok 10310 Office Tel : (+66 2) 7259100 Office Fax : (+66 2) 7259299 Email : customercarethai@electrolux.com Philippines Domestic Toll Free : 1-800-10-845-care 2273 Customer Care Hotline : (+63 2) 845 care 2273 Electrolux Philippines, Inc. 10th Floor.
