EQALF01TXST EQALF01TXWT EN USER MANUAL 1
Welcome Thank you for choosing ELECTROLUX. This manual contains all the information you need to safely and correctly use your water dispenser. Please read all the instructions prior to using the appliance, and keep this manual in a secure place for future reference. Do not remove the rating plate label which attached adhesive identification label containing the code, model number, manufacturer and other information.
Troubleshooting properties incident. d power To avoid danger of suffocation, keep plastic bag away from babies and children.
cabinet model not higher than 75%) (with cooling This dispenser can provide hot, cold and room temperature water. The heating method of machine can only be used within 1500m elevation. 7. To avoid any malfunction and keep your health better, please make sure you are using purified water and don’t fill the water bottles directly from the tap.
socket. The unit requires proper 5. Choose a place that is near a grounded electrical socket. Keep the dispenser at least 20cm away from walls and other appliances and furnitures on all 4 sides.
cooling On/Off. Located at the at the left side back of water dispenser.(page 6) beside until the water can flow out from the hot water spout when the hot water button be activated. 12. Unplug the unit when the unit will not be used for a long period to save electricity. (Fig. 5) 14. Never use organic liquids polishing chemical to clean the machine. 15. The thermostat to control temperature has been set up by manufacturer. There is no need to adjust it yourself.
14 1 2 3 16 5 6 4 7 13 8 9 10 11 12 bottle supporter button of hot water button of normal water button of cold water cooling switch heating switch indicator light spout of cold water spout of normal water 15 spout of hot water drip tray cabinet door condenser power cord drain hole handle
Installing the floor Bracket kit(Fig.6) 1. Use 13 mm screw to fix the fixing bracket on the middle of base pan. 2. Drill out a screw hole(6 mm) on the floor. 3. Insert a screw anchor (wall plug) into the drilled hole. 4. Move water dispenser, Align fixing bracket hole with screw hole of the floor. 5. Put the 25mm screw into the screw hole of fixing bracket. 6. Tighten the screw. 1 1 1 Fig.
The indicator lights show that the device is working correctly. After connecting the device, check if the indicators are on. (Fig.8) Indicates that the dispenser is power on. Indicates that the water is being heated. Indicates that the water is being chilled. Slide the child safety switch to left, holding it and push hot water button vertically, then the hot water can be out. (Fig.9/Fig.
Freestanding water dispenser with Cooling cabinet cooling switch. use the cooling cabinet. are Freestanding water dispenser with cabinet Note: Unplug the unit before cleaning. Unplug the water dispenser from the socket.
Dispense water from each spout till no water flow out from spout. Place a large bucket beneath the drain hole. Remove the drain caps and allow water to drain. Once finished draining, close the drain caps.(Fig. 16) Follow the “using your water dispenser” on page 7. Scald Hazard when tapping hot water and drain water from drain hole. Please make sure it is tight enough before long term use.
4. 5. on page 7, Make sure the water can flow out from the hot water spout when the hot water button be activated. Turn on the heating switch to heat water. 30 minutes later, drain off the liquid and clean it with water two or three times. It is recommend that this should be done every six months. 6. damage.
Troubleshooting Water dispenser does not work • Make sure the water dispenser is properly connected to a working socket and the heating/cooling switches are set ON. Water is leaking • Unplug the water dispenser, remove bottle and replace with new one. • Make sure the drain cap at the back side of water dispenser is tighten enough. No water is coming from the spout • Make sure the bottle is not empty, if empty, replace it with new one. • Make sure to completely depress the pushbutton controls.
L L_LED EARTH1 DISPLAY BOARD LED1 LED2 LED3 EARTH N_LED N POWER CORD L_HEAT L_COOL Hot SW Cool SW L_COMP1 L_COMP2 Cool Thermostat 2 Cool Thermostat 1 L_HEATER1 KEY1 L_HEATER2 L_COMP N_COMP COMP HEATER EARTH2 EARTH Hot Thermostat 1 KEY2 N_HEATER2 Hot Thermostat 2 N_HEATER1 EQALF01TXST Cooling Power 220-240V~ 100W 420W EQALF01TXWT 220-240V~ 100W 420W 2L/h(≤10°C) 75% 75% R134a/36g R134a/36g L318mmxW372mmxH1003mm L318mmxW372mmxH1003mm 15.5kg 15.
14 1 2 3 16 5 6 4 7 13 8 9 10 11 12 15
