Report No.：10072821-012 MSDS Report Sample Description Ni-MH rechargeable battery Applicant ZHE JIANG KAN BATTERY CO., LTD Pony Testing International Group www.ponytest.
Report ID：10072821-012 Page 1 of 10 Material Safety Data Sheet Ni-MH rechargeable battery Section 1 - Chemical Product and Company Identification Sample Name: Ni-MH rechargeable battery Sample Code: SC Company Identification: ZHE JIANG KAN BATTERY CO., LTD Address: No.998 Kai’en Road, Suichang County, Lishui City, Zhejiang Province Post Code: 323300 TEL: +86 578 8181635 FAX: +86 578 8181529 E-mail: info@kanbattery.
Report ID：10072821-012 Page 2 of 10 Section 3 - Hazards Identification EMERGENCY OVERVIEW Caution! The battery pack and enclosed cells should not be opened, disassembled, crushed, burned, or exposed to high temperatures. Under normal use and handling, the customer has no contact with the internal components of the battery. However, on some bad using conditions (high over charge, inverse charge, external shout circuit...
Report ID：10072821-012 Page 3 of 10 Eyes: Rinse immediately with plenty of water during at least 15-30 minutes, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses if easily possible. Get medical aid immediately. Skin: In case of contact, immediately flush skin with copious amounts of water for at least 15 minutes while removing contaminated clothing and shoes. Get medical aid. Wash clothing and shoes before reuse.
Report ID：10072821-012 Page 4 of 10 Section 6 - Accidental Release Measures General Information: No action shall be taken involving any personal risk or without suitable training. Review Section 5 and Section 7 sections before proceeding with clean-up. Use proper personal protective equipment as indicated in Section 8. If electrolyte leaks or spills, do not touch or walk through electrolyte. Spills/Leaks: Keep unnecessary people away. Remove heat and sources of ignition.
Report ID：10072821-012 Page 5 of 10 Section 8 - Exposure Controls, Personal Protection Exposure Limit: Composition: CAS# 7440-02-0 - TLV-TWA 1.5 mg/m3 (ACGIH) - PEL-TWA 1 mg/m3 (OSHA) Composition: CAS# 7440-50-8 - TLV-TWA 0.2 mg/m3 (ACGIH, fume) - TLV-TWA 1 mg/m3 (ACGIH, dust and mist) - REL-TWA 1 mg/m3 (NIOSH) - PEL-TWA 1 mg/m3 (OSHA) Composition: CAS# 1310-58-3 - TLV-TWA 2 mg/m3 (ACGIH, ceiling) Composition: CAS# 12597-69-2 - No date available.
Report ID：10072821-012 Page 6 of 10 Ø Respirators: Under normal condition of use and handing no special protection is required for sealed Battery. Use appropriate respirator if airborne dust or mist concentrations exceed. Personal Protective Equipment (In the Event of Battery Case Breakage): Always wear appropriate safety glasses with side shields or full face shield. Use appropriate gloves. Wear appropriate boots, apron or clothing. Use appropriate respirator.
Report ID：10072821-012 Page 7 of 10 Incompatibilities with Other Materials: Conductive materials, water, seawater, strong oxidizers and acids. Hazardous Decomposition Products: Oxides of nickel, oxides of metal, harmful gas and etc. Hazardous Polymerization: Will not occur.
Report ID：10072821-012 Sensitization Rate: Composition: CAS# 1310-58-3 Draize test, rabbit, skin: 50 mg/24H Severe. Teratogenicity: Not available. Page 8 of 10 Section 12 - Ecological Information Ecological Toxicity: Not available. Ecological Degradation: Not available. Biology Degradation: Not available. Other Information: If the battery is discarded into the environment, the harmful contents inside may be dangerous.
Report ID：10072821-012 Page 9 of 10 batteries are: alkalimanganese, zinc-carbon, nickel-metal hydride and nickel-cadmium batteries.” The requirements for shipping these batteries, in all modes of transportation, are that they be separated from each other to prevent short-circuits and to prevent movement that could lead to short-circuits. Products must also be packed in strong packaging that can withstand the rigors normal to transportation.
Report ID：10072821-012 Page 10 of 10 Notice to reader To the best of our knowledge, the information contained herein is accurate. However, neither the above named supplier nor any of its subsidiaries assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution.
