Installation Instructions Built-In Dishwasher If you have questions, call 1-877-4ELECTROLUX (US) or 1-877-435-3287, 245-8352 (Canada) or visit our website at: www.electroluxappliances.com BEFORE YOU BEGIN Read these Instructions completely and 1-800- IM PO RTANT — The dishwasher MUST be installed to allow for future removal from carefully. the enclosure if service is required. IMPORTANT - onserve ai If you received a damaged dishwasher, you should immediately contact your dealer or builder.
Installation Preparation PARTS SUPPLIED : Oo Two #8 Phillips flat head wood screws, 5/8" long to secure dishwasher to underside of countertop (in literature package). 0 Two Phillips head, color matched toekick screws (in literature package).
Installation PREPARE DISHWASHER ENCLOSURE Preparation hose is no more than 10 feet in length for proper drainage. ¢ The dishwasher must be fully enclosed on the top, sides and back, and must not support any part of the enclosure Clearance: When installed into a corner, allow 2" min. clearance between dishwasher and adjacent cabinet, wall or other appliances. Allow 25-5/8" min. clearance fromt he front of the dishwasher for door opening.
Installation Preparation PREPARE ELECTRICAL WIRING ll‘ay WARNING FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do no use an extension cord or adapter plus witthis appliance. ELECTRICAL REQUIREMENTS: ¢ This appliance must be supplied with 120V, 60Hz., and connected to an individual properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. ¢ Wiring must be 2 wire with ground.
Installation Instructions PREPARE HOT WATER LINE BEFORE YOU BEGIN ¢ The line may enter from either side, rear or floor within the shaded area shown in Figure F. ¢ The line may pass throughthe same hole as the electrical cable and drain hose. Or, cut an additional 1-1/2" dia. hole to accommodate the water line. If power cord with plug is used, water line must not pass through power cord hole.
Installation TEP 2 LEGS ADJUST LEVELING Instructions STEP 4 |INSTALL 90° ELBOW ¢ Wrap 90° elbow with thread seal tape. ¢ Move the dishwasher close to the installation location and lay it on its back. ¢ Install a 90° elbow onto the water valve. ¢ Do not over tighten 90° elbow, water valve bracket could bend or water valve fitting could break. ¢ Measure installation height and dishwasher height. Extend leveling legs out from the dishwasher base, 1/4" less than installation height.
Installation Instructions TEP 5 _|POSITION WATER LIND AND HOUSE WIRING STEP 7 |SLIDE DISHWASHER PARTIALLY INTO CABINET ¢ Position water supply line and house wiring on DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. DAMAGE WILL OCCUR. ¢ Slide dishwasher into the opening a few inches at a time. the floor of the opening to avoid interference with base of dishwasher and components under dishwasher. ¢ As you proceed, pull the drain hose through the opening under the sink.
Installation STEP 8 | POSTION DISHWASHER Instructions UNDER COUNTERTOP * Check to be sure that wires are secure under the dishwasher and not pinced or in contact with door springs or other dishwasher components TIP: Check tub insulation blanket, if equipped. It should be positioned so it is not bunched up or interfering with door springs. Check by opening and closing the door. ¢ Push dishwasher into cabinet. The front corners of the dishwasher door should be flush with cabinet doors.
Installation STEP 10 |SECURE DISHWASHER TO COUNTERTOP OR CABINET In this step you will need the 2 Phillips special head screws set aside prior to Step 1. The dishwasher must be secured to the countertop or the cabinet sides. When countertops are mad of wood, use Method 1. When countertops are Instructions STEP 11_|CONNECT WATER SUPPLY Connect water supply to 90° elbow. * Slide compression nut, then ferrule over end of water line. * Insert water line into 90° elbow.
Installation STEP 12 Instructions |CONNECT DRAIN LINE FOLLOW ALL LOCAL CODES AND DRAIN LINE INSTALLATION ¢ Connect drain line to air gap, waste tee or disposer using either previously determined method. ORDINANCES The drain hose molded end will fit 5/8", 3/4" or 1" diameter connections on the air gap, waste tee or disposer. Cut on the marked line as required for your installation.
Installation STEP 13 SUPPLY Instructions STEP 14_ |CONNECT POWER Review this list after installing your dishwasher to avoid charges for a service call that is not covered Skip this step if equipped with power cord. Verify that power is turned off at the source. by your warranty: LJ) Check to be sure power is OFF. * Remove junction box cover "A". ¢ Locate the three dishwasher wires, (white, black and green) with stripped ends. Insert dishwasher wires through the small hole in the junction box "B".
Installation STEP 15 |DISHWASHER WET TEST Instructions STEP 16 |REPLACE TOEKICK Oo Turn on power supply (or plug power cord into outlet, if equipped). 0 Turn dial to Normal "Wash" position. OH Close door. FO Check to be sure that water enters the dishwasher. If water does not enter the dishwasher, check to be sure that water and power are turned on. XO Check for leaks under the dishwasher. If a leak is found, turn power supply off, then tighten connections. Restore power after leak is corrected.
