Installation guide
Installation
Instructions
(A)
Rotate
90°
(B)
Fan
Blade
Openings
LY
Figure
14
9
OVEN
INSTALLATION
THIS
OVEN
CANNOT
BE
PROPERLY
INSTALLED
WITHOUT
REFERRING
TO
THE
MOUNTING
INSTRUCTIONS
FOUND
ON
BOTH
TEMPLATES.
THE
NEXT
STEP
IS
TO
READ
AND
FOLLOW
MOUNTING
INFORMATION
ON
BOTH
TOP
CABINET
AND
WALL
TEMPLATES.
NOTE:
THIS
OVEN
SHOULD
BE
ATTACHED
TO
AT
LEAST
ONE
WALL
STUD.
MOUNTING
PLATE
1.
Separate
Toggle
Nuts,
packed
in
the
INSTALLATION
HARDWARE,
from
4
Toggle
Bolts.
mm
!MPORTANT
Use
the
mounting
template
provided
to
Use
wood
screws
to
attach
mounting
plate
to
the
stud
or
studs.
Use
Toggle
Bolts
to
attach
mounting
plate
through
the
holes
at
A,
B,
C
and
D
UNLESS THOSE
HOLES
ARE
LOCATED
ON
THE STUD.
Insert
one
Toggle
Bolt
into
A,
B,
C
and
D
where
appropriate
(these
correspond
to
holes
of
the
Wall
Template)
and
put the
Toggle
Nuts onto
the
Toggle
Bolts.
See
Figure
15.
Refer
to
instructions
in
Wall
Template.
3.
Position
the
Mounting
Plate
with
the
Toggle
Bolts
attached
at
the
wall
location
and
insert
Toggle
Nuts
and
Bolts
through
the
holes
in
the
wall
with
the
Toggle
Nuts
closed.
See
Figure
16.
Use
Wood
Screws
to
attach
the
Mounting
Plate
to
studs.
NOTE:
Before
insertion,
be
sure
you
leave
a
space
more
than
the
thickness
of
the
wall
between
the
Mounting
Plate
and
the
end
of
each
of
the
Toggle
Nuts
(in
the
closed
position).
If
you
do
not
leave
enough
space,
the
Toggle
Nut
will
not
be
able
to
open
on
the
other
side
of
the
wall.
Also,
once
a
Toggle
Nut
opens,
it
cannot
be
withdrawn
from
the
hole;
therefore
make
sure
all
of
the
Toggles
are
in
the
correct
position
before
insertion.
Align
the
Mounting
Plate
carefully
and
hold
in
position
while
tightening
Toggle
Bolts.
Pull
Toggle
Bolt
toward
you
and
turn
clockwise
to
tighten.
See
Figure
17.
Toggle
Bolt
Toggle
Nut
“
Mounting
Plate
Figure
15
Space
more
~~
_
than
wall
thickness
Figure
17
Figure
16
MOUNTING
OVEN
TO
THE
WALL
Two
people
are
recommended
to
attach
the
Microwave
Oven/
Hood
to
the
Mounting
Plate.
1.
Thread
the
power
supply
cord
through
the
hole
made
in
the
bottom
of
the top
cabinet.
Install
the
oven
by
tilting
it
forward
and
sliding
it
onto two
tabs
of
the
Mounting
Plate.
Rotate
the
oven
up
so
it
rests
against
the
wall.
See
Figure
18
on
page
7.
Use
the
two
Top
Cabinet
Screws
and
two
Flat
Washers,
supplied
in
the
INSTALLATION
HARDWARE,
to
attach
the
unit
to
the
top
cabinet.
See
Figure
19
on
page
7.
Secure
the
bottom
of
the
oven
to
the
Mounting
Plate
by
using
two
Tapping
Screws
4
x
8
mm
from
the
INSTALLATION
HARDWARE.
See
Figure
19
on
page
7.