325 88-3071 Rev. 1-104 INSTRUCTION BOOK Modellnr:. Product no: Serienr:.
Congratulations from Electrolux It is better to use two pans rather than overfill one, or use half quantities. Dear Customer, 3. What to use Use firm fruit or vegetables and wash well before using. Congratulations with your new Hob. It is important that you become familiar with the functions and features of the Hob. You should therefore read these operating instructions as they will help you get the most out of your new Hob. Pay extra attention to sections marked .
Table of contents Contents Deep fat frying For safety purposes, when deep fat frying, fill the pan 1/3 full of oil. Do not cover the pan with a lid and do not leave the pan unattended. In the event of a fire, switch off at the electricity supply and cover the pan with a lid or damp cloth to assist in smothering the flames. Do not use water on the fire. Leave the pan to cool for at least 30 minutes before moving it. 4. Cooking the food Lower the food gently into the oil.
Safety information Never use plastic or aluminium dishes on the hob. These warnings are provided in the interests of your safety. Ensure you fully understand them before installing or using the appliance. Your safety is of paramount importance. If you are unsure about the meaning of these warnings contact the Customer Care Department for assistance. Never leave the hob unattended while deep fat frying, or heating fats and oils.
Service Description of the product Before calling service – Technical advice Sympton Solution The hob is not working Check your earth leak circuit breaker. Check fuses. The hob becomes hot The ceramic hob will reach a temperature of 80˚C. It may, however, become even hotter if you use cooking utensils with uneven bases or which does not match the size of the cooking zone. The fuses keep blowing Too many electrical appliances may be in use at the same time.
means that you do not have to adjust the heat constantly. CHEC control provides the zones with the following functions: Ceramic glass surface The ceramic glass surface has four cooking zones. When a zone is turned on, it will illuminate at various intervals depending on the heat setting selected. Even at the highest setting the zone is disconnected occasionally to ensure that the surface is not over-heated. The glass is hard, and has been tempered to withstand heat, cold and temperature shocks.
Electrical installation The electrical connection may only be performed by a qualified electrician/ competent person. The electrical connection must be carried out in accordance with prevailing regulations for appliances using heavy current. The connection must comply with any specific requirements specified by the local electricity supply authority. Before use Connection of child safety device on zones Turn the 2 control buttons to at the same time.
It is not necessary to attach the reinforcement beam to the work top surface, as it is held in place by a specially designed moulding, which is incorporated in the hob units flanges. Protection of the glass ceramic surface A protective film should be applied to the glass ceramic surface before use. This will make it easier to clean the surface, as well as preventing substances from being burnt onto the surface. The units externally measured length 145 mm: Cooker hood This is what to do: 1.
Mounting How to use Caution: In order to avoid a hazard this appliance must be installed according to these instructions for installation Switch symbols (to the left) control for regulating the small cooking zone at the rear The appliance unit can be mounted in any type of kitchen with a work top whose thickness is between 28 mm and 40 mm. Min. 47 mm control for regulating the double cooking zone at the front.
The decorative pattern on the ceramic surface can become scratched and marred with use, depending upon maintenance, but does not adversely affect performance. Residual-Heat indicator When you switch off a zone, an "H" in the display indicates that the zone is still hot. The residual heat indicator will continue to be illuminated as long as the temperature exceeds 80˚C. Such blemishes are not covered by the warranty and do not affect the operation of the hob.
Tips on the use of the ceramic hob unit Do not slide saucepans across the surface of the hob - always lift the pan when placing it on, or removing it from the ceramic surface. CHEC control Autostop If you forget to turn a cooking zone off after use, it will be disconnected automatically after a specific period of time. The higher the setting, the shorter the time before the zone is disconnected. Wipe the bottom surface of the pots and pans with a clean dry cloth before placing them on the ceramic surface.
Cleaning and maintenance of Recommended settings when using AUTOMAX The use of AUTOMAX means that the maximum power is connected for a specific number of minutes, depending on the setting chosen. The table below shows the length of time for which there is full power for each setting, and the functions for which each setting is suitable. Setting 1 2 3 4 5 6 7 8 9 Full power time (minutes) 1 minute 3 minutes 5 minutes 6.5 minutes 8.5 minutes 2.5 minutes 3.5 minutes 4.
Check whether your cooking utensils has level bases by placing the item in question upside down on a work top and positioning a ruler on the base. A curved base, both inwards and outwards, will prolong the cooking time and increase the energy consumption. If the diameter of the base is too small, the energy consumption will increase, and any food boiling over will burn onto the hot cooking zone.
When you turn on a zone the display will show: S F A Advice and hints for using the cooking zones E If you use the advice below you will save energy and make your cleaning tasks easier. over will burn onto the hot cooking zone. Saucepans with very shiny/bright bases will prolong the cooking time slightly compared with cooking utensils with matt/dark bases. Adjust the cooking zones correctly. Select the highest setting for the cooking zones until the food is brought to the boil.
