325 88-7680 Rev. 3-225 INSTRUCTION BOOK Model No. Product No Serial No.
Congratulations from Electrolux Dear Customer, Congratulations with your new Hob. It is important that you become familiar with the functions and features of the Hob. You should therefore read these operating instructions as they will help you get the most out of your new Hob. Pay extra attention to sections marked . These are warning texts to help you avoid accidents. Keep the operating instructions.
Table of contents Contents Page no For the user Your new appliance ...................................................................................... 2 Safety information ........................................................................................ 4 Description of the product ......................................................................... 5 Control button ....................................................................................... 5 Panel ..............................
Safety information Never leave the hob unattended while deep fat frying, or heating fats and oils. These warnings are provided in the interests of your safety. Ensure you fully understand them before installing or using the appliance. Your safety is of paramount importance. If you are unsure about the meaning of these warnings contact the Customer Care Department for assistance. The appliance is not intended for use by young children or infirm persons without supervision.
Service Description of the product Before calling service – Technical advice Sympton Solution The hob is not working Check your earth leak circuit breaker. Check fuses. The hob becomes hot The ceramic hob will reach a temperature of 80˚C. It may, however, become even hotter if you use cooking utensils with uneven bases or which does not match the size of the cooking zone. The fuses keep blowing Too many electrical appliances may be in use at the same time.
Technical specifications Two-phases zero-earth Cable type 1,5 mm² HO5VV-F. The cable outside diameter must be between 7,5 and 10,5 mm. Glass ceramic surface The glass ceramic surface has four zones. When a zone is turned on it is illuminated at various intervals depending on the setting chosen. Even at the highest setting the zone is disconnected occasionally to ensure that the surface is not overheated. The glass is hard, and has been tempered to withstand heat, cold and temperature shocks.
Electrical installation The electrical connection may only be performed by a qualified electrician/ competent person. The electrical connection must be carried out in accordance with prevailing regulations for appliances using heavy current. The connection must comply with any specific requirements specified by the local electricity supply authority. Before use Protection of the glass ceramic surface A protective film should be applied to the glass ceramic surface before use.
Operating instructions Switch symbols (to the left) Switch for regulating the plate at the rear pilot light Switch for regulating the large plate at the front. It is not necessary to attach the reinforcement beam to the work top surface, as it is held in place by a specially designed moulding, which is incorporated in the hob units flanges. The units externally measured length Switch for regulating the double plate at the rear 145 mm: Cooker hood Switch for regulating the small plate at the front.
Mounting Caution: In order to avoid a hazard this appliance must be installed according to these instructions for installation Pilot light Pilot light is activated when either of the zones are turned on, and will remain on until the cooking zones are switched off. Min. 47 mm The appliance unit can be mounted in any type of kitchen with a work top whose thickness is between 28 mm and 40 mm. Clearance The distance between the top side of the work top and the carpentry underneath must be at least 47 mm.
over will burn onto the hot cooking zone. Advice and hints for using the cooking zones If you use the advice below you will save energy and make your cleaning tasks easier. Saucepans with very shiny/bright bases will prolong the cooking time slightly compared with cooking utensils with matt/dark bases. Adjust the cooking zones correctly. Select the highest setting for the cooking zones until the food is brought to the boil. Then reduce the setting as far as possible, without the food going off the boil.
Tips on the use of the ceramic hob unit Do not slide saucepans across the surface of the hob - always lift the pan when placing it on, or removing it from the ceramic surface. Check whether your cooking utensils has level bases by placing the item in question upside down on a work top and positioning a ruler on the base. A curved base, both inwards and outwards, will prolong the cooking time and increase the energy consumption.
Cleaning and maintenance (use liqud AJAX or other diswashing liquid), and well wrung. All spills must be cleaned up immediately, while the burner is still warm. Use the cleaning agent supplied with the unit. Use Proper Cooking Utensils Make the most of your new ceramictop hob unit by using proper utensils of a good quality. Only pots and pans which are expressly intended for use on ceramictop hob units may be used. Utensils must, as a minimum, cover the entire circle which represents a given burner.
