instruction booklet GB gas hob EHG 9832
electrolux
electrolux 3 Welcome to the world of Electrolux Thank you for choosing a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable. You find some examples on the cover in this manual. Please take a few minutes to study this manual so that you can take advantage of the benefits of your new machine.
electrolux Contents Important Safety Information ................................................................... 5 Instructions for the User ........................................................................... 7 Description of the Hobs .................................................................................... 7 Operation ......................................................................................................... 8 Maintenance and Cleaning ................................
electrolux 5 Important Safety Information You MUST rread ead these war nings car efully befor e installing or using warnings carefully before the hob. If you need assistance, contact our Customer Care Department on 08445 613 613. I nstallation This appliance must be installed and serviced by a competent person as stated in the Gas Safety (Installation and Use) Regulations Current Editions and the IEE Wiring Regulations.
electrolux Do not use this hob if it is in contact with water. Do not operate the hob with wet hands. Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance. Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage. Never leave the hob unattended when cooking with oil and fats.
electrolux 7 Description of the Hob 3 2 1 67 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
electrolux Operation Hob burners control knobs The symbols on the knobs mean that : there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support. To light a burner: push in the relevant control knob and turn it anticlockwise to maximum position ( ), to ignite the burner. Upon ignition, keep the knob pushed down about 5 seconds. This will allow the "thermocouple" (Fig.
electrolux 9 Using the hob correctly To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a flat bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table beside).
electrolux Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob fr om the electricity supply from supply.. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. This appliance cannot be cleaned with steam or with a steam cleaning machine. The Hob T op Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing up liquid has been added.
electrolux 11 Pay attention when replacing the pan supports in order to avoid damaging the hob top. The Burners The burner caps and crowns can be removed for cleaning. Wash the burners caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth.
electrolux Something Not W orking? Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM SOLUTION There is no spark when lighting the gas. Check that the unit is plugged in and the electrical supply is switched on. Check that the RCCB has not tripped (if fitted). Check the mains fuse has not blown. Check the burner cap and crown have been replaced correctly, e.g. after cleaning. The gas ring burns unevenly.
electrolux 13 Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width: Depth: 894 mm 510 mm CUT OUT DIMENSIONS Width: Depth: 830 mm 480 mm SUPPL Y CONNECTIONS SUPPLY Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V~ 50 Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse HEA T INPUT HEAT Rear Left Burner (auxiliary) Rear Right Burner (auxiliary) Central Right Burner (semi rapid) Central Left Burner (semi rapid) Fron
electrolux BURNER RAPID POSITION M A X MIN SEMI-RAPID A U X I L I A R Y TRIPLECROWN TYPE OF GAS NATURAL GAS 20 mbar VALUE = 37.78 MJ/m 3 Ws - 50.7 MJ/ m3 LPG GAS 28-30/37 mbar VALUE = 49.92 MJ/Kg NOMINALTHERMAL POWER kW MAX MIN 0.45 1.0 0.33 4.0 1.2 0.286 0.057 0.190 0.038 0.095 0.028 0.381 0.114 119 Adjust. 96 Adjust. 70 Adjust. 146 Adjust. NOMINALTHERMAL POWER kW 2.8 0.75 2.0 0.45 1.0 0.33 4.0 1.2 NOMINALFLOW RATE g/h 202 4 3.
electrolux 15 Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. 813 Current Editions and the ETCI Rules for Electrical Installations.
electrolux If it is fitted below 400 mm a space of 50 mm must be allowed from the edges of the hob. The minimum distance combustible material or a cooker hood can be fitted above the hob is 650 mm. For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S 813 Current Edition Section 7- Permitted Locations of Appliance. Installation IMPOR TANT Any gas installation must be carried out by a GAS SAFE REGISTER installer.
electrolux 17 Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Ensure that the main connection pipe does not exert any strain on the hob.
electrolux Building In B uilding over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2.
electrolux 19 Fitting the hob into the worktop Carry out the building in of the hob as follows: 1. place the seals supplied with the hob on the front edge of the cut out. Then, place them at 27 mm from the side edges and at 10 mm from the rear edge, as shown in the diagram, taking care that the seals meet without overlapping. 2. Place the hob in the cut out, taking care that it is centred. 3. Fix the hob with the relevant fixing clamps, supplied with the injectors kit (see diagram).
electrolux Electrical Connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician, e.g.
electrolux 21 Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath. A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that the cut off plug is disposed of safely safely.. The replacement of electric cable must be carried out exclusively by the service force centre or by personnel with similar competencies, in accordance with the current regulations.
electrolux Fault Finding Preliminary Electrical Systems Check Blue Brown START Isolate appliance and carry out: A: Earth Continuity check. YES NO Green Yellow Blue Green Yellow Brown Carry out: C: Polarity check. Carry out: D: Resistance to Earth check. Has inlet fuse blown? Electricity supply should now be satisfactory. YES NO PLUG (with cover removed) Earth Wire Green/Yellow Neutral Wire Blue SOCKET (face view) ( ) E( ) FUSE Inlet wiring faulty. Rectify any fault.
electrolux 23 A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 W (Ohm), check all earth wires for continuity and all contacts clean and tight. B. INSULA TION CHECK INSULATION Appliance electrically disconnected, all switches ON. a) meter set on W (Ohms) x 1 scale. Test leads from L to N in appliance terminal block.
electrolux Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the taps ignition switches Check continuity from ignition switches connector to ignitor unit Light burner manually Check by
electrolux 25 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: 1) Re-ignite the burner and set to MIN. 2) Remove the control knob.
electrolux Conversion from Natural Gas to LPG IMPOR TANT The replacement/conversion from natural gas to LPG should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted. The gas rate is adjusted to suit.
electrolux 27 Guarantee/Customer Service Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: · The appliance has been correctly installed and used only on the electricity supply stated on the ratin
electrolux Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning 08445 616 616 Your telephone call will be automatically routed to the Service Force Centre covering your postcode area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www .servicefor ce.co.uk www.servicefor .serviceforce.co.
electrolux 29 European Guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law.
electrolux
electrolux 31
www.electrolux.co.uk 35693-2603 11/09 R.
