user manual Gas hob GB EHG90932
electrolux Electrolux. Thinking of you. Share more of our thinking at www.electrolux.com CONTENTS Safety information Installation Product description Operating instructions Helpful hints and tips 2 4 8 9 10 Care and cleaning What to do if… Technical data Environment concerns 10 11 12 13 Subject to change without notice SAFETY INFORMATION Warning! These instructions are only valid in the countries whose symbols appear on this booklet's cover.
electrolux 3 • Use only the accessories supplied with appliance. • Be careful when you connect the appliance to the near sockets. Do not let electricity bonds touch the appliance or hot cookware. Do not let electricity bonds tangle. Installation • You must read these instructions. The manufacturer is not responsible for any injury to persons and pets or damage to property caused by failure to obey these requirements.
electrolux with applicable cable. Speak to your local Service Force Centre. • The appliance must have the electrical installation which lets you disconnect the appliance from the mains at all poles with a contact opening width of minimum 3 mm. • If the fixing bracket is near to the terminal block, always make sure the connection cable does not come in contact with the edge of the bracket.
electrolux 5 components as shown in the diagram. Screw the parts together without using excessive force. 1 2. Remove the caps and crowns of the burner. 3. With a socket spanner 7 remove the injectors and replace them with the ones which are necessary for the type of gas you use (see table in Technical Data section). 2 3 1 End of shaft with nut 2 Washer 3 Elbow Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper.
electrolux must fit an applicable pressure adjuster on the gas supply pipe. Adjustment of minimum level To adjust the minimum level of the burner: 1. Light the burner. 2. Turn the knob on the minimum position. 3. Remove the control knob. 4. With a thin screwdriver, adjust the bypass screw position. If you change from natural gas 20 mbar to liquid gas, fully tighten the adjustment screw in.
electrolux 7 1 2 3 4 5 1 Green and Yellow 2 3 amp fuse 3 Brown 4 Cord clamp 5 Blue Should the plug need to be replaced for any reason, the wires in the mains lead are coloured in accordance with the following code: Green and Yellow - Earth Blue - Neutral Brown - Live 2. Connect the blue (neutral) wire to the terminal in the plug which is marked with the letter 'N' or coloured black. 3. Connect the brown (live) wire to the terminal in the plug which is marked with the letter 'L' or coloured red.
electrolux A a) Removable panel b) Space for connections Kitchen unit with oven The hob recess dimensions must obey the indication and the kitchen unit must be equipped with vents to let a continuous supply of air. The electrical connection of the hob and the oven must be installed separately for safety reasons and to let easy remove oven from the unit.
electrolux 9 Control knob for gas burner Symbol Symbol Description Description minimum gas supply no gas supply / off position internal crown ignition position / maximum gas supply double crown OPERATING INSTRUCTIONS Ignition of the dual burner Warning! Be very careful when you use open fire in kitchen environment. Manufacturer decline any responsibility in case misuse of the flame 1 Always light the burner before you put cookware.
electrolux Important! In the absence of electricity you can ignite the burner without electrical device; in this case approach the burner with a flame, push the relevant knob down and turn it counter-clockwise to maximum gas release position. If the burner accidentally goes out, turn the control knob to the off position and try to light the burner again after minimum 1 minute. after installation or a power cut. It is normal. Turning the burner off To put the flame out, turn the knob to the .
electrolux 11 • You can remove the pan supports to easily clean the hob. • To clean the enamelled parts, cap and crown, wash it with warm soapy water. • Stainless steel parts wash with water, and then dry with a soft cloth. • The pan supports are not dishwasher proof; they must be washed by hand . • When you wash the pan supports by hand, take care when you dry them as the enamelling process occasionally leaves rough edges. If necessary, remove stubborn stains using a paste cleaner.
electrolux Problem Possible cause Remedy The flame is blow out immediately after ignition • Thermocouple is not heated sufficient • After lightning the flame, keep the knob pushed for approximately 5 seconds. The gas ring burns unevenly • Burner crown is blocked with food residues • Make sure that the injector is not blocked and the burner crown is clear of food particles. If there is a fault, first try to find a solution to the problem yourself.
electrolux 13 Heat input Gas supply: G20(2H) 20 mbar Dual Crown burner: 5,0 kW Appliance class: Rapid burner: 3,0 kW Semi-rapid burner: 2,0 kW By-pass diameters Auxiliary burner: 1,0 kW TOTAL POWER: G20(2H) 20mbar = 14 kW G30 (3+) 28-30 mbar = 974 g/h G31 (3+) 37 mbar = 956 g/h Electric supply: 230 V ~ 50 Hz Category: II2H3+ Gas connection: R 1/2" 3 Burner Ø By-pass in 1/100 mm Auxiliary 28 Semi-rapid 32 Rapid 42 Double Crown (external crown) 56 Double Crown (internal crown)
electrolux Packaging material The packaging materials are friendly to the environment and can be recycled. The plastic components are identified by marking: >PE<,>PS<, etc. Discard the packaging materials as household waste at the waste disposal facilities in your municipality.
electrolux 15
www.electrolux.
