EN User manual Gas hob EHG6832 GB IE
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Operation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 7 8 9 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11 Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 1
• • • • • • • • • • • • • • • damage to property caused by failure to obey these requirements. To prevent the risks of structural damage or physical injury, installation, connection of the appliance to the power supply and gas system, setting up and maintenance must only be done by qualified personnel in compliance with standards and local regulation force. Make sure that the appliance is not damaged because of transport. Do not connect a damaged appliance.
Installation Warning! The following instructions about installation, connection and maintenance must be carried out by qualified personnel in compliance with standards and local regulations in force. Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S.
Important! Failure to ensure the correct assembly will cause leakage of gas. Important! Make sure that the gas supply pressure of the appliance obeys the recommended values. 1 Rigid connection: Carry out connection by using metal rigid pipes (copper with mechanical end). gas. Warning! If you install this appliance in Cyprus or Malta, change the injectors to the G30/G31 type of Injectors replacement 1. Remove the pan supports. 2. Remove the caps and crowns of the burner. 3.
This hob is designed to be connected to a 230 V 50 Hz AC electrical supply. Before switching on, make sure the electricity supply voltage is the same as that indicated on the hob rating plate. The rating plate is located on the bottom of the hob. The hob is supplied with a 3 core flexible supply cord incorporating a 3 amp plug fitted. In the event of having to change the fuse, a 3 amp ASTA approved (BS 1362) fuse must be used.
a) Removable panel b) Space for connections A Kitchen unit with oven The hob recess dimensions must obey the indication and the kitchen unit must be equipped with vents to let a continuous supply of air. The electrical connection of the hob and the oven must be installed separately for safety reasons and to let easy remove oven from the unit.
Control knobs Symbol Symbol Description ignition position / maximum gas supply Description no gas supply / off position minimum gas supply Operation Ignition of the burner Warning! Be very careful when you use open fire in kitchen environment. Manufacturer decline any responsibility in case misuse of the flame 1 2 Always light the burner before you put cookware. 3 To light the burner: 1. Turn the control knob counterclockwise to the maxi) and push it down. mum position ( 2.
If the burner accidentally goes out, turn the control knob to the off position and try to light the burner again after minimum 1 minute. The spark generator can start automatically when you switch on the mains, after installation or a power cut. It is normal. or pan. You must only use the wok stand on the Triple Crown. When you install the wok stand, make sure that the recesses in the frame fit on the bars of the pan supports. Turning the burner off To put the flame out, turn the knob to the symbol .
• The pan supports are not dishwasher proof; they must be washed by hand. • When you wash the pan supports by hand, take care when you dry them as the enamelling process occasionally leaves rough edges. If necessary, remove stubborn stains using a paste cleaner. • Make sure you position the pan supports correctly after cleaning. • To make burners work correctly, make sure that the arms of the pan supports are in the centre of the burner.
Labels supplied with the accessories bag Stick the adhesive labels as indicated below: 1 2 3 MOD. MOD. PROD.NO. PROD.NO. SER.NO SER.NO 03 IT DATA DATA MADE IN ITALY MODEL MOD. PROD.NO. SER.NO. 0049 TYPE 230V-50Hz IP20 MODEL 1 Stick it on Guarantee Card and send this part 2 Stick it on Guarantee Card and keep this part 3 Stick it on instruction booklet These data are necessary to help you quickly and correctly. These data are available on the identification plate from the injectors kit.
Appliance class: 3 By-pass diameters Burner Ø By-pass in 1/100 mm. Auxiliary 28 Burner Ø By-pass in 1/100 mm. Semi-rapid 32 Triple Crown 56 Gas burners NORMAL POWER NORMAL POWER REDUCED POWER kW kW inj. 1/100 mm m³/h inj. 1/100 mm G30 G31 g/h g/h Auxiliary burner 1.0 0.33 70 0.095 50 73 71 Semi-rapid burner 2.0 0.45 96 0.190 71 145 143 Triple Crown burner 4.0 1.4 146 0.
397176101-A-422010 www.zanussi.
