contents 2 Safety instructions... 3 Parts identification... 4 Installation instructions... 5 Installation procedure IEEE 5 6 Operation. oes 7 Ignition burners coco c eee 7 Using the hob correctly Maintenance and care Glass top Burner-caps & bases . What to do if Technical specifications -= occ committeemen ss 9 Warranty conditions... ooh 9 Thank you for choosing and using Electrolyte home appliances. Electrolyte Group of Sweden is one of the world largest home appliances companies.
safety instructions Safety Instructions « Do not use gas other than that which is specified on the label attached. * Do not place anything, e.g. flame tamer, asbestos mat, between pan and pan support as serious damage to the appliance may 1) * Do not remove the pan support and enclose the burner with a wok stand not supplied by Electrolyte as this will concentrate the flame and deflect the heat onto the top plate.
parts identification 4 EHG8238BC Outer Cap Pan Support T-Sensor Tempered Glass Top Plate Inner Cap Drip Pan electrode Burner Base Thermonuclear Burner Box EHG8248BT Outer Cap Pan Support T-Sensor Tempered Glass Top Plate Inner Cap Drip Pan
parts identification 5 The Class of the appliance: Class 3 * These instructions are only valid if the country symbol appears on the appliance. » |f the symbol does not appear on the appliance, iris necessary to refer to the technical instructions which will provide the necessary instructions conceding modification of the appliance to the conditions of use of the country.
Installation instructions Installation procedure Have the installer show you the location of the gas shut off valve and how to shut it off in emergency. Be certain all packing materials are removed from the hob before operating to prevent fire or smoke damage that could be caused by the presence of these materials. Observe all instructions for minimum clearance to any combustible surfaces. These should be In accordance with information on the rating plate and with national fire laws.
Gas connection Before installing the appliance, check that the location provides the required clearances from combustible materials and check if necessary to provide protection to adjacent surfaces as required by the regulation. Make provision for the gas supply to be connected to the location. Cut the opening in the bench top by the cardboard template given in the hob packing or to the dimensions shown in Fig 7. Remove the hob from the carton. Install the hob in the cut-out.
7 operation Ignition boomers 1. heck to make sure that the gas supply is accessible and set up with the necessary and appropriate fittings / connectors. 2. Tum all control knobs to off position. 3. This device is fitted with a safety tap to control the gas flow. When the dot on the knob lines up with the following symbols on the panel, these conditions prevail : o Full ON position # 4 1 Reduce rate position To close, rotate the knob to the right until you feel the tap's distinct click. 4.
Use of Timer Function . Turn on the gas hob according to the normal operation method to ensure proper combustion. 2. Press “ "once. The display will turn on at default Input desired timer settings while the display is blinking. i he display will stop blinking after 2 seconds if no input is detected at Then, display will remain lit for 5 seconds before the timer turns off automatically. 3. Timer function: Maximum 3 hour and minimum 1 minute. 4.Press or" —"to set time. i.
Precautions for dry burning prevention a. Dry burning prevention burner {left burner). Please read below instruction carefully for the dry burning prevention probe to function properly. WARNING During usage, the top surface of the dry burning prevention probe must be in full contact with bottom of the pot otherwise it will not function properly. Rounded or pointed bottom pot, casserole, clay pot and aluminum pot are not suitable for the left burner Integrated with dry burning prevention probe. 1.
maintenance and care 8 Glass top « If necessary, use a matchstick or brush to car ports. « Persistent stains may require vigorous rubbing with + After cleaning, ensure the burner caps are reassembled nylon scourer or creamed powder cleansers. Household properly into position. enamel cleaners are available, follow the manufacturer + After cleaning service, when assembling the burner instructions in their use.
9 warranty conditions EHG8248BT Timer fault codes and handling method Status Phenomenon The code Resolution shown When 10 seconds are left, the buzzer will continuously beep for 20 seconds at the frequency of 1Hz. When 0 seconds are left, Return knob to the “End of Timer" | the flame out is executed and the "0:00" off position. prompt display continues for 10 seconds before oon Reactivate timer disappearing. The indicator light at the by reigniting the upper right corner of the display will keep fire.
9 warranty conditions Standard warranty conditions We, Electrolyte, undertake that with warranty period (refer to each country location for warranty period months) this Electrolyte appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labor, materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity supply stated on the rating pla
