user manual CN Gas Hob EHG 30800 X
electrolux
electrolux 3 Welcome to the world of Electrolux Thank you for choosing a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable. You find some examples on the cover in this manual. Please take a few minutes to study this manual so that you can take advantage of the benefits of your new machine.
electrolux Contents For the User Important safety information .............................................................................. 5 Operation .......................................................................................................... 7 Using the hob correctly ..................................................................................... 8 Cleaning and Maintenance ................................................................................
electrolux 5 English Important safety information This warnings has been given for the safety of you and others. We therefore ask you to carefully read the procedures of installing and using this cooker. Installation The work of installation must be carried out by competent and qualified installers according to the regulations in force. • Any modifications to the domestic electrical mains which may be necessary for the installation of the appliance should be carried out only by competent personnel.
electrolux • Ensure a good ventilation around the appliance. A poor air supply could cause lack of oxygen. • Ensure that the gas supply complies with the gas type stated on the identification label, placed near the gas supply pipe. • This appliance is not connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations. Particular attention shall be given to the relevant requirements regarding ventilation.
electrolux 7 Operation Hob burner control knob The symbols on the knob mean: = no gas supply = maximum gas supply = minimum gas supply For easier lighting, proceed before putting a pan on the pan support. Lighting the burner )To light the burner, turn the relevant knob anticlockwise to maximum position ( ) and push down the knob to ignite. After lighting the flame, keep the knob pushed down for about 5 seconds.
electrolux Using the hob correctly Practical hints The burner To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used. Triple crown burner diameter 18-26 cm • For easier lighting, proceed before putting a pan on the pan support. • Use only pans or pots with flat bottom. • Take care when frying food in hot oil or fat, as the overheated splashes could easily ignite.
electrolux 9 Cleaning and Maintenance Disconnect the appliance from the electrical supply, before carrying out any cleaning or maintenance work. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. This appliance cannot be cleaned with steam or with a steam cleaning machine. The burner Wash the enamelled components with warm soapy water. Never use abrasive cleaners. The burner cap and crown can be removed for cleaning.
electrolux z z After cleaning, make sure that the pan supports are correctly positioned. Do not leave acid or alkaline substances (e.g. vinegar, salt, lemon juice, etc.) on the cooktop. The ignition electrode The electric ignition is obtained through a ceramic electrode with a metal electrode. Keep these components very clean, to avoid difficult lighting, and check that the burner crown holes are not obstructed.
electrolux 11 Gas burner NORMAL REDUCED POWER POWER NORMAL POWER BURNER NATURAL GAS LIQUID GAS G20 (2H) - 20 mbar (Butane/Propane) 28-30/37 mbar kW Triple crown burner kW 4,0 g/h inj. 100/mm m3/h inj. 100/mm G30 G31 146 0,381 98 291 286 1,2 By-pass diameters Burner Triple crown Ø By-pass in 1/100 mm.
electrolux Installation z z z z Gas connection The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed.
electrolux 13 Adaptation to different types of gas A. Injectors replacement ) • Remove the pan supports. • Remove the burner's caps and crowns. • With a socket spanner 7 unscrew and remove the injectors (Fig. 1), and replace them with the ones required for the type of gas in use (see table «Gas burner» - page 11). • Reassemble the parts, following the same procedure backwards. • Replace the rating label (placed near the gas supply pipe) with the relevant one for the new type of gas supply.
electrolux Electrical connection The appliance is designed to be connected to 220 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force.
electrolux 15 Remplacement of the voltage cable The connection of the voltage cable to the appliance's terminal block is of type "Y". This means that its replacement requires the specific equipment of a technician. In this case, only cable type H05V2V2-F T90 must be used. The cable section must be suitable to the voltage and the working temperature. The yellow/green earth wire must be approximately 2 cm. longer than the phase wires (Fig. 3-a).
electrolux Building In TC 51 0 0 29 Fig. 5 Fitting the hob to the worktop These hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in Fig. 6. Carry out the building in of the hob as follows: 1. Put the relevant sealings, supplied with the hob, on the edges of 140 55 27 0 490 550 M given in 40÷50 IN 30 240 are 591 These hobs can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hobs dimensions are shown in Fig.
electrolux 17 the cut out, taking care that the sealings meet without overlapping; 2. place the hob in the cut out, taking care of its centring; 3. fix the hob with the relevant screws (Fig. 7). The traction of the screws is able to trace the sealing, any excess of which can then be easily removed. If several 30 cm hob are to be installed side by side into the same cut out, an assembly kit including a support side bracket and supplementary sealings is available at our authorized Service Centres.
electrolux Service and original spare parts This machine, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results. Any repair work which needs to be carried out should be done with the utmost care and attention. For this reason we recommend that for any problem you contact the dealer who sold it to you, or our nearest authorized Service Centre, specifying the nature of the problem, the appliance model (Mod.
electrolux 19
www.electrolux.cn 397102801 08/08 R.
