Gas-Hob USER MANUAL Mod.
English Important Safety Information These warnings are provided in the interest of safety. You MUST read them carefully before installing or using the appliance. About Installation, Cleaning and Maintenance • • • • • • • • • It is mandatory that all operations required for the installation are carried out by a qualified or competent person, in accordance with existing rules and regulations. Disconnect the appliance from the electrical supply, before carrying out any cleaning or maintenance work.
Contents Description of the appliance ......................... 3 Instruction for the User ................................. 3 Cleaning and Maintenance ............................ 4 Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Guarantee - After Sales Service ................... 5 Safety Instructions Technical Data ................................................ 6 Instruction for the Installer ............................
If you cannot light the flame even after several attempts, check the "cap" (Fig. 1 lett. A) and the "crown" (Fig. 1 lett. B) are in the correct position. A To put the flame out, turn the knob to the symbol z. In the absence of electricity, ignition can occur without the electrical device; in this case approach the burner with a flame, push the relevant knob down and turn it anti-clockwise until it reaches the "maximum" position.
Guarantee - After Sales Service Original spare parts This appliance, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results. Any repair work which needs to be carried out should be done with the utmost care and attention. For this reason we reccomend that for any problem you contact the dealer who sold it to you, or our nearest authorized Service Centre, specifying the nature of the problem and the particular model which you own.
Technical Data Gas Burner Rating Ultra-Rapid Burner 4,0 kW Class 3 Appliance Setting Liquid Gas G30/G31 28 - 30 mbar Gas connection Electric Supply G 1/2" 220 / 240 V ~ 50 / 60 Hz - This appliance complies with the following Directives: 73/23 - 90/683 (Low Voltage Directive); 89/336 (Electromagnetical Compatibility Directive); 90/396 (Gas Appliances) 93/68 (General Directives) and subsequent modifications. Hob recess dimensions Length Width 270 mm. 490 mm.
Gas connection Choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. Use the same attention when the hob is combinated with an oven. IMPORTANT - To ensure a correct operation, a saving of energy and the long-life of the appliance, the voltage pressure of the appliance must correspond to the recommended values.
Electrical Connection The appliance is designed to be connected to 220 / 240 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: Neutral 1. check that the main fuse and the domestic installation can support the load (see the rating label); 2. check that the power supply is properly earthed in compliance with the current rules; 3.
Adaptation to different types of gas Replacing the burner injectors Town gas 1. Remove the pan supports. 2. Remove the burner's caps and crowns. 3. With a socket spanner 7 unscrew and remove the injectors (Fig. 6), and replace them with the ones required for the type of gas in use (see Table 2). Town gas Ultra-rapid burner burners: screw the provided grid filter assembly "C" (Ø 16) on it. 4. Reassemble the parts, following the same procedure backwards. 5.
Building In 51 0 29 0 Dimensions are given in millimetres These hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in Fig. 9. The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the hob, the cut out edges must have a minimum distance of 100 mm. Hanging forniture units or hoods must be placed at 650 mm minimum from the hob.
Possibilities for insertion Kitchen unit with door Proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in Fig.11. The panel fitted under the hob should be easily removable to allow an easy access if a technical assistance intervention is needed. Kitchen unit with oven The hob recess dimensions must comply the indication given in Fig.
06/06 Grafiche MDM - Forlì
