C e ra m ic G l a s s I n d u c t i o n H o b Installation and Operating Instructions EHD 72100-X 374 461 703-A-100406-01 g
Dear customer, Please read these operating instructions carefully. Pay particular attention to the section “Safety information” on the first few pages. Please retain these operating instructions for later reference. Pass them on to possible new owners of the appliance. 1 3 2 The following symbols are used in the text: Safety instructions Warning: Information concerning your personal safety. Important: Information on how to avoid damaging the appliance.
Contents Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cooking surface layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control panel layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Instructions 1 Safety instructions 3 5 Please comply with these instructions. If you do not, any damage resulting is not covered by the warranty. This appliance conforms with the following EU Directives: – 73/23/EEC dated 19.02.1973 Low Voltage Directive – 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive 92/31/EEC – 93/68/EEC dated 22.07.1993 CE Marking Directive Correct use • This appliance should be used only for normal domestic cooking and frying of food.
Safety during use • Overheated fats and oils can ignite quickly. When cooking with fat or oil (e.g. chips) do not leave the appliance unattended. • There is the risk of burns from the appliance if used carelessly. • Remove stickers and film from the glass ceramic. • Cables from electrical appliances must not touch the hot surface of the appliance or hot cookware. • Switch the cooking zones off after each use. Safety when cleaning • For cleaning, the appliance must be switched off and cooled down.
Description of the Appliance Cooking surface layout Induction cooking zone 1850 W Induction cooking zone 1400 W with power function 2500 W with power function 1800 W Control panel Induction cooking zone 1400 W with power function 1800 W 6 Induction cooking zone 2300 W with power function 3700 W
Control panel layout Left-hand side Child lock pilot light Warm up pilot light Timer indicator Heat setting indicator Heat setting selection Child lock Heat setting indicator Warm up pilot light Timer Automatic warm-up function/ Power function Automatic warmup function/Power function Timer selection Heat setting selection Right-hand side Warm up pilot light Heat setting indicator Heat setting indicator Timer indicator Warm up pilot light Heat setting selection Automatic warm-up function/ Power f
Touch Control sensor fields The appliance is operated using Touch Control sensor fields. Functions are controlled by touching sensor fields and confirmed by displays and acoustic signals. Touch the sensor fields from above, without covering other sensor fields.
Residual heat indicator 1 3 Warning! Risk of burns from residual heat. After being switched off, the cooking zones need some time to cool down. Look at the residual heat indi. cator Residual heat can be used for melting and keeping food warm. The induction cooking zones create the heat required for cooking directly in the base of the cookware. The glass ceramic is merely heated by the residual heat of the cookware.
Operating the appliance 3 Use the induction cooking zones with suitable cookware. Switching the appliance on and off Control panel 3 3 Display Pilot light Switch on Touch for 2 seconds / lights up Switch off Touch for 1 second / none goes out After switching on, within approx. 10 seconds a heat setting or a function must be set, otherwise the appliance automatically switches itself off. Switching off also works by touching and at the same time.
Using the automatic warm-up function All cooking zones are equipped with an automatic warm-up function. The automatic warm-up function sets the cooking zone to the highest setting for a certain period of time and then automatically switches back to the cooking setting that was originally set.
Switching the power function on and off The power function makes more power available to the induction cooking zones, e.g. to bring a large quantity of water to the boil quickly. The power function is activated for 10 minutes. After that the induction cooking zone automatically switches back to heat setting 9.
Using the child safety device 3 The child safety device prevents unintentional use of the appliance. The child safety device can only be switched on and off, if the appliance is switched on, but no cooking zone has a heat setting set. Activating the child safety device Step Control panel 1. Switch on the appliance (Do not set a heat setting) 2. Touch Indicator/Signal Appliance switches off. The child safety device is activated. 3 If you want to use a locked cooking zone (indicator sounds.
Using the timer All cooking zones can use each use one of the two timer functions at the same time. 3 Function Condition Outcome after time has elapsed Safety cut-out When a heat setting is set acoustic signal 0 lights up Cooking zone switches off Countdown timer When cooking zones are not used acoustic signal 0 lights up If a heat setting is set on this cooking zone in addition to a countdown timer, the cooking zone is switched off after the time set has elapsed.
Setting the time Step Control panel Indicator 1. Select cooking zone Pilot light for the selected cooking zone flashes 2. Touch 0 to 99 minutes or After a few seconds the pilot light flashes more slowly. The time is set. The time counts down. 3 If other Timer functions are set, after a few seconds the shortest remaining time for the right-hand or left-hand timer is displayed. The respective pilot light flashes. Switching off the Timer function Step Control panel Display 1.
Changing the time Step Control panel Indicator 1. Select zone Pilot light of the selected cooking zone flashes faster Time remaining is displayed 2. Touch cooking or 01 to 99 minutes After a few seconds, the pilot light flashes more slowly. The time is set. The time counts down. Displaying the time remaining for a cooking zone Step Control panel field Display 1.
Safety cut-out Cooking surface • If after switching on the cooking surface, a heat setting is not set for a cooking zone within approx. 10 seconds, the cooking surface automatically switches itself off. • If one or more sensor fields are covered for longer than approx. 10 seconds, e.g. by a pan placed upon it, a signal sounds and the cooking surface switches off automatically. • If all cooking zones are switched off, the cooking surface automatically switches itself off after approx. 10 seconds.
Tips on Cooking and Frying 3 Information on acrylamides According to the latest scientific knowledge, intensive browning of food, especially in products containing starch, can constitute a health risk due to acrylamides. Therefore we recommend cooking at the lowest possible temperatures and not browning foods too much.
Pan size Induction cooking zones adapt automatically to the size of the bottom of the cookware up to a certain limit. However the magnetic part of the bottom of the cookware must have a minimum diameter depending upon the size of the cooking zone. 3 Diameter of cooking zone [mm] Minimum diameter of dish base [mm] 210 180 180 145 145 120 The cookware must be placed centrally on the cooking zone. Tips on energy saving 2 2 Place cookware on the cooking zone before it is switched on.
Examples of cooking applications The information given in the following table is for guidance only. Heat setting Cookingprocess 0 suitable for Cooking time Tips/Hints Off position Keeping food warm Keeping cooked foods warm as required Cover Melting Hollandaise sauce, melting butter, chocolate, gelatine 5-25 mins. Stir occasionally Solidifying Fluffy omelettes, baked eggs 10-40 mins.
Cleaning and Care 1 1 1 Take care! Risk of burns from residual heat. Warning! Sharp objects and abrasive cleaning materials will damage the appliance. Clean with water and washing up liquid. Warning! Residues from cleaning agents will damage the appliance. Remove residues with water and washing up liquid. Cleaning the appliance after each use 1. Wipe the appliance with a damp cloth and a little washing up liquid. 2. Rub the appliance dry using a clean cloth. Removing deposits 1.
What to do if … Problem Possible cause The cooking zones will not More than 10 seconds have switch on or are not function- passed since the appliance ing was switched on Switch the appliance on again. The child safety device is switched on Deactivate the child safety device (See the section “Child safety device”) Several sensor fields were touched at the same time Only touch one sensor field Safety cut-out has been triggered Remove any objects (pan, cloths, etc.
Problem Possible cause and number are displayed Electronics fault 1 3 Remedy Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house’s wiring system) If after switching on again, is displayed again, call the customer service department If you are unable to remedy the problem by following the above suggestions, please contact your dealer or the Customer Care Department.
Disposal 2 2 Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities. Old appliance W on the product or on its packaging indicates that this prodThe symbol uct may not be treated as household waste.
Installation Instructions Safety instructions 1 1 The laws, ordinances, directives and standards in force in the country of use are to be followed (safety regulations, proper recycling in accordance with the regulations, etc.) Installation may only be carried out by a qualified electrician. The minimum distances to other appliances and units are to be observed.
A device must be provided in the electrical installation which allows the appliance to be disconnected from the mains at all poles with a contact opening width of at least 3 mm. Suitable isolation devices include line protecting cut-outs, fuses (screw type fuses are to be removed from the holder), earth leakage trips and contactors.
Assembly 27
Rating Plate 941 177 622 ELECTROLUX 7,4 kW 50 Hz 230 V Induction 7,4 kW 55GDD86AG 30 EHD72100X
Service In the event of technical faults, please first check whether you can remedy the problem yourself with the help of the operating instructions (section “What to do if…”). If you were not able to remedy the problem yourself, please contact the Customer Care Department or one of our service partners. In order to be able to assist you quickly, we require the following information: – Model description – Product number (PNC) – Serial number (S No.
374 461 703-A-100406-01 Subject to change without notice The Electrolux Group. The world´s No.1 choice. The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
