instruzioni per l'uso manual de instrucciones ïäçãßåò ÷ñÞóçò EGL3001X EGL3000X
XXX XXX XXX - 00 - 20102005
Use & Care Manual Assembly Instrucions Included Outdoor Grill with Electronic Ignition Welcome & Congratulations . . . 2 General Safety Instructions . . . 3 Grill Features . . . . . . . . . . . . . . . 5 Grill Assembly Side shelf Built-In Instructions . . . . . . . 6-12 Gas Requirements Pre Operation . . . . . . . . . . . 13-15 Using the Grill . . . . . . . . . . . . . . 18 Lighting the Grill Using the Rotisserie & Side Burning . . . . . . . . . . 16-22 Care and Maintenance . . . . . . 23 Troubleshooting .
Welcome & Congratulations WELCOME TO THE WORLD OF ELECTROLUX Thank you for choosing a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable. You find some examples on the cover in this manual. Please take a few minutes to study this manual so that you can take advantage of the benefits of your new machine.
General Safety Instructions GENERAL INFORMATION FOR COOKING APPLIANCES You MUST read these warnings carefully before installing or using the appliance. If you need assistance, contact our Customer Care Centre. Keep this instruction book for future reference and ensure it is passed on to any new owner. INSTALLATION It is mandatory that all operations required for the installation are carried out by a qualified or competent person, in accordance with existing rules and regulations.
General Safety Instructions For hygiene and safety reasons, this appliance should be kept clean at all times. A build-up of fats or other foodstuff could result in a fire. Take care when frying food in hot oil or fat, as the overheated splashes could easily ignite. Carefully supervise cookings with fats or oil, since these types of foodstuff can result in a fire, if over-heated. If the appliance is out of order, disconnect it from the gas supply.
Grill Features 7 1 8 2 9 12 3 13 4 10 5 11 6 1. Roll top grill hood 8. Warming shelf 2. Grilling/Cooking surface 9. Infrared back burner 3. Side Shelf 10. Electronic igniter: main, rear infrared & side burner 4. Control knob: back infrared burner 11. Cart with door 5. Control knobs: main burners 6. Convection vents 12. Side Burner 7. Hood Handle 13.
Grill Assembly Shelf Hooks IMPORTANT: Remove all protective plastic film from stainless steel parts prior to assembly/use. This film is installed at the factory to prevent damage that could occur during shipment and handling. Fig. 1 Fig. 2 SIDE SHELF ATTACHMENT 1. Attach the shelf to the left side of grill by inserting the shelf hooks into the slots on the side of the grill and pushing down on the shelf assembly until level with grill. (See Fig. 1) Fig. 3 2.
Grill Assembly 3. Install cooking grates on the ledges provided on the grill to create your cooking surface. (See. Fig. 6) Cooking Grates Fig. 6 Warming Shelf 4. Place warming shelf on support brackets by setting it flat across brackets allowing the two holes to line up with the holes on each bracket. (See Fig. 6) Fig. 7 5. Remove label from drip tray and verify that the tray is installed correctly. The drip tray is located underneath the grill, inside the storage compartment. (See Fig.
Side Burner Assembly SIDE BURNER PARTS ASSEMBLY Side Shelf Tabs 1. Attach the side shelf to the grill by inserting the shelf hooks into the slots on the side of the grill and pushing down on the shelf assembly until level with the grill. (See Fig. 8) Fig. 8 2. Lock the side shelf in place by inserting (2) hex head screws in the side burner. (See Fig. 9) Screw Holes Fig. 9 NOTE: A power screwdriver extension is needed to insert screws. 3. Install burner and cap. (See Fig. 10-11) 4.
Side Burner Assembly 5. Attach the three (3) wires coming out from the side of the grill and the side burner wire to the igniter terminals. (See Fig. 13-14) Fig. 13 NOTE: It does not matter which wire goes to which terminal on the igniter. Fig.
Built-In Instructions for model EGL3001X ! WARNING The Electrolux Grill model EGL3001X can be installed as a built-in grill. If installed as a built-in grill, the outdoor cooking center must be constructed of non-combustible material. PLANNING AND DESIGN Start by identifying the number and size of components you want to include: Grill, side burner, access doors for storage or other items you may wish to furnish such as: refrigerator, sink, warming drawer.
Built-In Instructions for model EGL3001X OUTBOARD IGNITER PLATE INSTALLATION (SEE DRAWING ON FOLLOWING PAGE) The electronic igniters require a standard size deep electrical box, (available at a local hardware store), with a minimum depth of 6 cm to be mounted in the structure. It should be placed on the right front or right side of the outdoor cooking center, with the center of the igniter button no more than ca 10 cm from the grill.
Built-In Instructions for model EGL3001X Note: Make Sure To Use Non-Combustible Material For Construction Note A: Wire & Plumbing Cutout Left & Right Sides 10 x 15 cm Opening Minimum GFI Electrical Outlet For Rotisserie Motor 2 cm Required igniter Cutout Note A* Top 5 cm 10 cm A 15 cm Side Cutout View C Front B Open Space Minimum Clearance To Open Hood 12,5 cm 4 cm 90 cm Max 7 Mi 0 cm nim um 2 cm Max 2 cm Max 3.
Gas Requirements GENERAL INFORMATION Never attach an unregulated gas line to the appliance. Connection to an unregulated gas line can cause excessive heat or fire. Verify the type of gas supply to be used, Liquid Propane or Butane (L.P.). NOTE: Always have a qualified service technician perform difficult conversions or modifications.
Gas Requirements L.P. TANK INFORMATION Never use a dented or rusted L.P. tank or cylinder with a damaged valve. Cylinders must not be stored in a building, garage, or any other enclosed area. L.P. TANK USE • When turning the L.P. tank on, make sure to open the valve SLOWLY two (2) complete turns to insure proper gas flow. • When not in use, gas supply cylinder valve is to be in the “OFF” position. • The tank supply system must be stored upright to allow for vapor withdrawal.
Pre Operation GENERAL INFORMATION Although all gas connections on the grill are leaked tested at the factory prior to shipment, a complete gas tightness check must be performed at the installation site due to possible mishandling in shipment, or excessive pressure unknowingly being applied to the unit. Periodically check the whole system for leaks, or immediately check if the smell of gas is detected. BEFORE TESTING Do not smoke while leak testing. Extinguish all open flames.
Lighting the Grill BEFORE LIGHTING ! WARNING Do not attempt to “Light” the grill if the odor of gas is present!! Important! Before Lighting... Check the gas supply line for cuts, wear or abrasion. Always keep your face and body as far away from the grill as possible when lighting. Fig. 15 GRILL BURNER LIGHTING Lighting the Grill with electronic igniter 1. Make sure tall control knobs are in the “OFF” position. 2. Open the gas supply valve located on top of your L.P. tank. ATTENTION: When turning the L.
Lighting the Grill NOTE: If the burner does not light in 4 seconds, turn the knob to the “OFF” position and wait 5 minutes before trying again. Fig. 16 5. Repeat above steps to light remaining burners. MATCH LIGHTING If by chance the electronic igniter does not light the burner, the burner may be lit with a match.
Using the Grill GRILL LOCATION ! WARNING Do not use the grill in garages, breezeways, sheds or any enclosed area. Never operate the grill in enclosed areas as this could lead to a carbon monoxide buildup, which could result in injury or death. Place the grill on a level surface. Avoid moving the grill while it is operation. NOTE: The grill will operate best if it is not facing directly into the wind.
Using the Rotisserie & Side Burners Note: ROTISSERIE KIT is an accessory and must be purchased separately and is only available on some markets. The grill rotisserie system is designed to cook items from the back using infrared heat. The rotisserie burner is an infrared type which provides intense searing radiant heat. Preferred by chefs over other cooking methods, this intense heat is magnificent for searing in the natural juices and nutrients found in quality cuts of meats.
Using the Rotisserie & Side Burners Note: ROTISSERIE KIT is an accessory and must be purchased separately and is only available on some markets. Pointed End Of Rod ATTACHING THE ROTISSERIE (purchased separately) * For bracket installation, see instruction sheet provided with the optional rotisserie kit. The motor is mounted on a bracket on the left side of the grill by sliding the motor over the bracket with the cord facing the back of the grill.
Using the Rotisserie & Side Burners ROTISSERIE LIGHTING Open the lid. Push and turn the control knob for the rotisserie counter clockwise to the “HIGH” position. Wait 5 seconds. Then press and hold the electronic igniter button. You’ll hear a snapping sound. If the burner does not light in 4 seconds, turn the control knob to OFF and wait 5 minutes before trying again. Once lit, turn the control knob to the desired setting. (See Fig. 18) Fig.
Using the Rotisserie & Side Burners SIDE BURNER LIGHTING Push and turn the control knob to the “HIGH” position and immediately press and hold the electronic igniter button. You’ll hear a snapping sound. It may be necessary to hold the electronic starter button for about 4 seconds. If the burner does not light in 4 seconds, turn the knob to the “OFF” position and wait 5 minutes before trying again. Repeat above steps to light remaining burners. (See Fig. 20) Fig.
Care and Maintenance DRIP TRAY The drip tray located below the grill, inside the cart, should be cleaned periodically to prevent heavy buildup of debris. NOTE: Allow the drip tray to cool before attempting to clean. Important: Do not leave the grill outside during inclement weather unless it is covered (cover sold separately). Rain water can collect inside of the grill, the grill cart or the drip tray if left uncovered.
Care and Maintenance IGNITER ACCESS (UNDER SIDE BURNER SHELF): To remove igniter, unscrew igniter push button and locking nut from front panel of the side burner and igniter will fall out through the bottom IGNITER ASSEMBLY: 1. The Battery, spring and igniter cap must be installed before using. 2. Install the battery, positive side first. 3. Slide spring assembly over battery. 4. Screw igniter cap onto igniter.
Troubleshooting GENERAL TROUBLE SHOOTING You should inspect the burners at least once a year or immediately if any of the following conditions occur: • The smell of gas • Flames appearing mostly yellow. (some yellow at the tips is OK) • The Grill will not get hot enough. • Burners make a snapping noise. • The Grill heats unevenly. SPIDER AND INSECT WARNING Spider and insects can nest in the burners of this or any other grill and cause the gas to flow from the front of the burner.
Troubleshooting PROBLEM SOLUTION Grill will not light when the igniter button is pushed. Is your gas supply turned on? Is there gas in your tank? Check your gas level. Is one of your burners turned on? Allow up to four seconds of gas flow to ignite. Is your igniter working? - You should hear a snapping sound when you press the igniter? - If you hear a snapping sound can you see a spark at the electrodes? NOTE: You will need to remove your cooking grates and flavor grids to see the electrodes.
Troubleshooting PROBLEM SOLUTION Grill will not light with a match or low heat with dial set to "High" position. Is your gas supply fully turned on? Is there gas in your tank? Check your gas level. Shut off gas supply, disconnect gas line at tank, reconnect the line to the tank. Make sure all the knobs are in the off position, then open the gas supply valve on the L.P. tank very slowly 1/4 turn, then open fully (at least two full turns). Check flame height again.
Troubleshooting PROBLEM SOLUTION Flare-ups Check flavor grids and cooking grates for excess food or grease build-up. Ensure grill is not placed directly in the path of wind. Be sure drip tray is clean, (do not use aluminum foil on drip tray.) NOTE: Some flare-ups may be inevitable if cooking greasy foods. Burner flame is mostly yellow or orange, possibly in conjunction with smell of gas. Check the burner inlet for obstructions. Particularly at air inlets for each burner.
Warranty STANDARD GUARANTEE CONDITIONS We, Electrolux, undertake that if within 12 months of the date of the purchase this Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
Warranty conditions Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances.
