Gas Hobs INSTR UCTION BOOKLET INSTRUCTION Please read this instruction booklet before using the appliance EGH 35674-8902 GB
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 950950 Installation z z z z z This appliance must be installed and serviced by a competent person as stated in the Gas Safety ( Installation and Use) Regulations Current Editions and the IEE Wiring Regulations. For appliances installed in the Republic of Ireland please refer to NSAI-Domestic Gas Installations I.S.
Contents For the Installer For the User Important Safety Information 3 Engineers technical data Description of the Hob 4 Installation 10 Operation 5 Building In 11 Maintenance and Cleaning 5 Electrical connections 12 Something Not Working? 6 Wiring Diagram 13 Service and Spare Parts 7 Fault Finding 13 Customer Care Department 7 Commissioning 15 Guarantee Conditions 8 Conversion from Natural Gas to LPG 15 Description of the Hob 2 3 3 1 4 5 6 1. 2. 3. 4. 5. 6.
Operation HOB BURNERS To light a burner, turn the relevant control knob anticlockwise to maximum position. At the same time push the electric ignition pushbutton which is marked by a little spark. Then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table).
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.
Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Electrolux Service Force Centre by telephoning: 0870 5 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.
Guarantee Conditions Electrolux Guarantee conditions We, Electrolux, undertake that if, within 12 months of the date of the purchase, this Electrolux appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: * The appliance has been correctly installed and used only on the gas and electricity supply stated on the rating plate.
Instructions for the Installer Engineers technical data OVERALL DIMENSIONS Width: Depth: Height: SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner 580 mm 500 mm 8 mm Electric: 230-240V 50Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. CUT OUT DIMENSIONS Width: 550 mm Depth: 470 mm Thickness: 30 mm Ignition HT Spark Spark Generator Ispra Control's BF 50066 - 230-240V 0.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. 813 Current Editions and the ETCI Rules for Electrical Installations.
Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to RC 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Ensure that the main connection pipe does not exert any strain on the hob.
Fitting the Hob into the worktop Carry out the building in of the hob as follows: • put the seals supplied with the hob, on the edges of the cut out: place them exactly on the front and rear edge and at 50 mm. from the side edges, taking care that the seals meet without overlapping; • place the hob in the cut out, taking care that it is centred; • fix the hob with the relevant fixing clamps and screws, as shown in the diagram. When the screws have been tightened, the excess seal can be removed.
Wiring Diagram L 1 A 2 0 3 220/240 4 5 A. IGNITOR SWITCH 6 B B. IGNITOR UNIT N Fault Finding Preliminary Electrical Systems Check Blue Green Yellow Earth Wire Green/Yellow START Isolate appliance and carry out: A: Earth Continuity check. ( ) E( ) FUSE Brown SOCKET (face view) PLUG (with cover removed) Neutral Wire Blue N L Blue Brown Green Yellow YES NO Carry out: C: Polarity check. Has inlet fuse blown? NO YES Inlet wiring faulty. Rectify any fault.
Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjusted Check position of the electrode Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the taps ignition switches Check continuity from igni
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: ) Re-ignite the burner and set to MIN. Remove the control knob.
55-77 High Street Slough Berkshire, SL1 1DZ Tel: 08705-950950 © Electrolux Household Appliances Limited 2000 Grafihe MDM - Forlì CUSTOMER CARE
