miniCool EA 3200 EA 3200 D Operating Instructions 207.5167.
Please read these operating instructions carefully before putting the refrigeration unit into operation. If you later sell or dispose of it, please ensure that the new owner receives these operating instructions. Please follow the installation details below carefully Guarantee is valid for products installed as described only. Thank you for choosing our appliance. We are sure it will provide you with trouble-free use.
CONTENT S 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Unpacking View of the appliance Cleaning Positioning the appliance 4.1. Installation instruction Using the appliance 5.1. Temperature regulation Ice cubes Useful suggestions Defrosting, cleaning and maintenance Changing the lightbulb Reversing the door hang Replacing the decorative door panel Assembly of door handle Customer service Putting into operation, technical data 14.1.
1. Unpacking After removal from the cardboard packaging, make sure the appliance is not damaged. If you find damage to the appliance resulting from transport, report it immediately to the transportation firm. 2. View of the appliance EA 3200 Figure 1. 1. door 4. thermostat knob 2. bottle retainer 5. freezer** 3. evaporator 6. lamp IN CASE IF YOUR REFRIGERATOR IS EQUIPPED WITH LOCK, THE MANUFACTURER DO NOT ACCEPT LIABILITY FOR LOSS OR DAMAGE OF KEYS.
3. Cleaning Clean the refrigerator thoroughly at intervals, as necessary. Remove the shelves; these, the cabinet interior and the door should be washed with a warm solution of sodium bi-carbonate. Finally wipe over with a cloth rinsed in warm water only, and dry with a clean cloth. Do not wash any plastic parts in water that is more than hand warm, and do not expose them to dry heat. The outside of the cabinet should be wiped down regularly with a clean, damp cloth.
3. Ventilation must be provided as shown in alternatives A, B, C or D (fig 2-3) 4. The ventilation duct must at least measure 105mm x the width of the refrigerator 5. Only the entire cooling unit must project into the duct as shown 6. Air passing through the duct must not be preheated by any source of heat 7. Ventilation grills, if used, must have openings of at least 200cm2 each During installation, please ensure the mains plug is accessible at all times. 5.
. Useful suggestion Do not overfill the appliance. It is advisable to leave some space between the products in the cabinet to ensure efficient and even cooling. If the shelves are packed too tightly there may be unacceptable temperature variations. 8. Defrosting, cleaning and maintenance Frost will gradually form on the cooling surfaces and it must not be allowed to become too thick since it acts as an insulator and interferes with the cooling. Semi-automatic defrosting (fig.
9. Changing the lightbulb (If available) If the lightbulb needs changing, pull out the plug and proceed as follows: Press the metal reflector to one side and draw the lamp covering backwards. Replace the bulb and push the covering back into place. A new max. 10-watt bulb can be obtained at any Electrolux service shop. 10. Reversing the door hang, (Fig.
12. Assembly of door handle (Fig. 11) 13. Customer service Before you call a service engineer, carry out the following simple tests: Is there a power failure? Check the fuses. Is the plug firmly connected to the socket and is the socket switched on? Check the socket by plugging in another appliance, e.g. a table lamp. Is the thermostat at the correct setting? (normally 3 or 4).
14. Putting into operation Technical data: Model Type Gross volume Mains operation Input Energy consumption Climate class Refrigerant EA 3200; EA 3200 D E 30/60 60 litre 100V (AC) 95W 1,4 kWh/24h N 540g NH3 +H2O 14.1 Connecting to electrical mains The appliance may only be operated from nominal voltage mains as shown on the data plate. The appliance mains plug may be connected to a mains socket earthed in accordance with regulations.
15. Environmental protection information The appliance does not contain any CFCs/HCFCs. Ammonia (natural hydrogen and nitrogen compound) is used as a refrigerating agent in the refrigeration unit. The ozone-friendly cyclopentane is activated as a motive agent for the PU foam insulation. Sodium chromate is used for corrosion protection (less than 2 weight % of the coolant). 16. Recycling After unpacking the appliance, the packing materials should be delivered to a local collection site.
Printed by Xerox Hungary Ltd. Rev.: 2003. 12. 05.
