]nsta]]atian Instructions Vc_t l/ood
BEADAND SAVET [] [] [] [] [] [] Read all instructions [] [] SE IINS U [] [] before installing [] [] [] [] [] all installation [] [] [] [] [] DONS [] [] [] [] [] [] [] [] the hood. For your safety, please read and observe you antbipate [] all safety instructions. Thb guide will help connections. [] [] [] [] [] [] [] For toll-free telephone support in the U.S. and Canada: 1-877- 4ELEOTROLUX (1-877-435-3287) For online support and lnternet www.eleet roluxusa.
TABLE OF'CONTENT9 [] [] [] [] [] [] [] [] [] [] [] Finding Information ........................................... 2 PleaseReadAnd SaveThis Guide ...................2 Questions.......................................................... 2 TableOf Contents.............................................. 3 Safety ................................................................... 4 ImportantSafetyInstructions..............................4 Preparing for installation ..................................
IIM [] [] £NT S£FEW IINS U [] [] [] [] [] [] [] [] [] [] ONS [] [] [] [] [] [] [] [] [] [] Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual. Safety items throughout Warning or Caution based on the risk type. this manual are labeled with a ,5!:,,This is the safety alert symbol. It is used to alert you to potential personal hazards. Obey all safety messages that follow this symbol to avoid possible or death.
SAFETY PRECAUTIONS
VEB F'¥PACKAGECONTENTS [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] Use and Care Manual ,, Suction Cup IIN [] [] [] [] [] [] [] A qualified installer must complete installation is your responsibility. the installation of this builtqn appliance. [] Proper Carefully check the location where the hood is to be installed. The hood should be placed for convenient access.
9" Hood Overall Dimensions Model Width "A" Width "B" E30WV60EPS 29 7/8" (759mm) 2313/16" (605ram) E36WV60EPS 357/8" (911mm) 2313116"(605ram) E48WV12EPS 47 7/8" (1216ram) 2313/16" (605ram) Overall Dimensions Isometric View (9" hood shown) Figure 1 18" Hood Overall Dimensions Overall Dimensions Isometric (18" hood View shown) Figure 2 Model Width "A" Width "B" E308WV60ES 29 7/8" (759mm) 2613/16" (681ram) E368WV60ES 357/8" (911mm) 2613/16" (681ram) E488WV126S 47 7/6" (1216mm)
Verticam Exhaust Duct Location E3OWV6OEPS, E36WV60EPS, E308WV6OES, E368WV60ES Top View Figure 3 6 1/8" (156mm) t 8" (203ram) Round Duct Collars Horizontal Vertical Exhaust Duct Location E48WV12EPS Top View Exhaust Duct Location E308WV60ES, E368WV60ES Rear View Figure 5 Figure 6 f / \ \ \\ \ \ \ \ \\ \ \ \ \ \ Horizontal Exhaust Duct Location E488WV120S Rear View Figure 7 5304449697 Custom Transition for use with E488WV120S (not included) Figure 8
EL,,EC CAL,CONDUT IIIL,,,,,,,OCAT ONS [] [] [] [] [] 1 1/2" 7/8"_ (11Pqm) Holes [] [] [] [] [] [] [] [] [] [] [] 1/2" (_8 _!_)m_rl Conduit Location E3OWV6OEPS, E36WV60EPS, E48WV12EPS, E3OSWV6OES, E368WV60ES, E488WVI20S Top View 9" and 18" Hoods Figure 9 Conduit Location E308WV6OES, E368WV60ES, E488WV120S ReadBack View 18" Hoods Figure 10 Electrical Conduit Locations Model No.
Refer to the table beUow for recommended provide adequate performance. Model E3OWV6OEPS maximum straight Rengths of duct to Duct Size Maximum Equivalent Straight Lengths 10" 50' E36WV60EPS 31/4"x10" E48WV12EPS 50' E3OSWV6OES E368WV60ES E488WV120S E3OWV6OEPS 60' E36WV60EPS E3OSWV6OES E368WV60ES Refer to the table beUow for recommended wall cap equivaUent straight Rengths.
IP PABINGTHE C£B N [] [] [] Minimum hood. [] [] [] [] hood clearances [] [] effective [] [] m [] [] [] [] [] m [] m are zero inches (0") to the rear, sides and top of the Thirty inches (30") is the minimum any cooking surface. Maximum (914mm).
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] It is the owner's responsibility to ensure that the electrical connection of this appliance is performed by a qualified electrician. The electrical installation including minimum supply wire size and grounding, must be in accordance with the latest revision of the National Electric code ANSI/NFPA and local codes and ordinances.
IINIWAI,,,,,,,,,,I,,,,,,,,,,ING TIE HOOD [] [] m m m m [] [] [] [] m m m [] [] [] [] m m m m [] First temporarily mount a 2x4 ledger board 30" (762mm) from the finished countertop. Then, remove the filters from the hood canopy and remove the shields below the power ventilator. Secure the hood through the keyhole slots in the top of the hood and/or the slot hole in the rear of the hood. Remove the temporary support ..... ....... : ....... ledger.
MAKINGTHE ELEC [] [] [] [] Figure 13 [] [] [] [] C£L CONNECTION [] [] [] [] [] [] [] [] [] [] [] Electrical power source wiring can connected through the top or back hood. Access the wiring inside the canopy in the area to the right side [] [] be of the hood of the power ventilator. Connect the pre=wJred 12" long black, white and green wires to the corresponding black, white and ground (green) wire from the power source wiring. Use wire nut connectors to secure the connections.
VE [] [] :'¥1NG THEOPERATION [] m m m [] [] [] [] m m m [] [] [] [] m m m m @ install the fiRers. @ Verify that the hood control knobs are in the OFF position. @ Turn on the main power supply. o The hood has two knobs that control the function of the hoods Halogen lights and the exhaust blower. Turning the knobs clockwise will turn on the lights and the blower. The blower has a variable speed range between settings.
