Installation Instructions Over the Range Microwave Oven BEFORE YOU BEGIN Read these instructions • • Note to Consumerfuture reference.
Installation Instructions CONTENTS General information Important Safety Electrical Requirements Hood Exhaust Damage Parts C Instructions ..................... - Shipment/Installation Included Mounting 7 Space ............................................ Placement of Mounting guide Plate ................ 8-10 Removing the Mounting Plate ................... 8 Finding the Wall Studs .............................. 8 Determining Wall Plate Location ...............
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.
Installation Instructions HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 11. OUTSIDE TOP EXHAUST (EXAMPLE The following chart describes ONLY) an example of one possible ductwork installation, DUCT PIECES EQUIVALENT LENGTH x NUMBER USED = EQUIVALENT LENGTH Roof Cap 24 Ft, x (1) = 24 Ft, 12Ft.
Installation Instructions NOTE: If you need to install ducts, note that the total duct length of 31/,'' x 10" rectangular or 6" diameter round duct should not exceed 140 equivalent feet. Maximum For satisfactory air movement, the total duct length of 31¼'' x 10" rectangular or 6" diameter round duct should not exceed 140 equivalent feet. Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully. Elbows, transitions, wall and roof caps, etc.
Installation DAMAGE - SHIPMENT/ INSTALLATION • If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. • If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. • If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and installer. Instructions PARTS INCLUDED HARDWARE PACKET PART QUANTITY Wood Screws (1¼.
Installation Instructions TOOLS YOU WILL NEED Pencil # 1 and #2 Phillips screwdriver Tin snips (for cutting damper, if required) Scissors Electric drill with and 5/8" drill bits (to cut template, if necessary) 3/16", 1/2" Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only) Saw (saber, hole or keyhole) Gloves Stud finder or Hammer (optional) Level Safety goggles Duct and masking tape MOUNTING SPACE NOTES: Bottom edge of
Installation 1.PLACEMENT Instructions OF THE MOUNTING PLATE A_ REMOVING THE MICROWAVE B_ FINDING THE WALL STUDS OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE 1. Remove the installation instructions, L Exhaust adaptor, filters, glass tray and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven, 2.
Installation DETERMINING Instructions WALL PLATE LOCATION Plate position - beneath flat bottom cabinet Draw a vertical line on the wall at the center of the 30" wide space.
Installation Instructions D_ ALIGNING THE WALL PLATE !;22 _ :222:..... REAR HoleA Horizontal Line WAL_ TEMPLATE Centerline , Draw a VerticalLine ' on Wallfrom Center notches i____ of Top Cabinet Area E HoleC HoleB Horizontal Line Draw a Horizontal line on wall from bottom of "Rear Wall Template". CAUTION: Wear gloves to avoid cutting fingers on sharp edges. 1. Draw a Vertical line on the wall at the center of the NOTE: Holes A, B and C are inside area E.
Installation 2. INSTALLATION TYPES Instructions (Choose This microwave oven is designed for adaptation to the following three types of ventilation: A. Recirculating B. Outside (Non-Vented Top Exhaust NOTE: This microwave is shipped after being assembled for "Recircutating". And exhaust adaptor is shipped assembled to the filler-upper. Select the type of ventilation required for your installation and proceed to that section. Ductless) (Vertical Duct) C.
Installation A_ RECIRCULATING INSTALLATION (Non-Vented Instructions Ductless) OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Mount the Microwave Oven AI.__.ATTACH THE MOUNTING TO THE WALL 3.
Installation MOUNT THE MICROWAVE Instructions especially when mounting flush to bottom of cabinet. OVEN Cabinet Front Cabinet Bottom Shelf Filler Block "--_ Equivalent to Depth of FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: installation. Cabinet Recess gning Screw Do not grip or use handle during Microwave Oven Top NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. 4.
Installation Instructions B.__. OUTSIDE TOP EXHAUST INSTALLATION (Vertical Duct) OVERVIEW B1. Attach Mounting Plate to Wall B2. Prepare Top Cabinet B3. Adjust Blower | B4. Check Damper Operation B5. Mount Microwave Oven B6. Adjust Exhaust Adaptor B7. Connect Ductwork BI._. ATTACH THE MOUNTING TO THE WALL PLATE To use toggle bolts: Spacing for Toggles More Than Wall Thickness I I i Toggle Wings i Mounting Plate Waii _ BoltEnd 3.
Installation Instructions B2._,.. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP B3. ADAPTING MICROWAVE BLOWER FOR OUTSIDE CABINET TOP EXHAUST 1. Remove You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor, and save screw that holds 2. Lift up the blower plate. blower plate to microwave. Blower Plate Back of Microwave Screw 3. Carefully • Read the instructions TEMPLATE.
Installation Instructions B5.__.MOUNT THE MICROWAVE OVEN FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: installation. 5. Place the blower unit back into the opening. Do not grip or use handle during NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.
Installation B5.m_. MOUNT THE MICROWAVE Instructions OVEN B6._.ADJUST (cont.) THE EXHAUST ADAPTOR Open the top cabinet and adjust the exhaust adaptor to connect to the house duct. Cabinet Front Cabinet Bottom Shelf Blower-Plate Filler Block "--_ Back of Microwave Damper Depth of Cabinet Equivalent to Recess For Front-to-Back Self-Aligning Screw Adjustment, Slide the Exhaust Adaptor as Needed Microwave Oven Top 4. Attach the microwave oven to the top cabinet. 5.
Installation Instructions C__OUTSIDE INSTALLATION BACK EXHAUST (Horizontal Duct) OVERVIEW C1. Prepare Rear Wall C2. Attach Mounting Plate to Wall T C3. Prepare Top Cabinet 04. Adjust Blower i C5. Mount the Microwave Oven C1. PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST C2. ATTACH THE MOUNTING TO THE WALL PLATE You need to cut an opening in the rear wall for outside exhaust. Attach the plate to the wall using toggle bolts.
Installation C2.__. ATTACH THE MOUNTING TO THE WALL (cont.) Instructions PLATE C4m ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST 1. Remove To use toggle bolts: and save screw that holds blower Plate to microwave. Spacing for Toggles More Than Wall Thickness Blower motor screw. I Toggle Wings 2, Mounting Plate Lift up the Blower Plate. Blower Motor Back of Microwave Wall Bolt End "_'_'_r-.... Blower Motor Screw 3. Place the mounting plate against the wall and 3.
Installation 6. Instructions C5m MOUNT THE MICROWAVE Place the blower unit back into the opening, OVEN End A End B FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN, CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven. IMPORTANT: installation.
Installation C5._,..MOUNT THE MICROWAVE Instructions OVEN (cont.) Install grease filters. See the Owner's Manual packed with the microwave. Cabinet Front Cabinet Bottom Shelf Filler Block Depth of Cabinet - Recess quivalent to Self-Aligning Screw Microwave Oven Top 4. Attach the microwave oven to the top cabinet. 5, Insert 2 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw. ghten center screw completely.
Installation BEFORE 1, Make Instructions YOU USE YOUR MICROWAVE sure the microwave oven has been 6, Read the Owner's Manual. installed according to instructions. 7, KEEP INSTALLATION 2, Remove all packing material from the microwave oven. 3. Install turntable and ring in cavity. 4. Replace house fuse or turn breaker back on. 5, Plug power cord into a dedicated 20 amp electrical outlet. 22 '?7 ; :2 Vfi} / / , ;" :* INSTRUCTIONS THE LOCAL INSPECTOR'S USE.
