Specification Sheet
High standards of quality at Electrolux Home Products, Inc.
mean we are constantly working to improve our products.
We reserve the right to change specifications or
discontinue models without notice.
Electrolux Major Appliances, N.A.
USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-877-4electrolux (1-877-435-3287) • electroluxicon.com
CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • electroluxicon.ca
Meets
requirements of
ASSE 1006
E24ID75SPS 12/16 © 2016 Electrolux Home Products, Inc.
Built-In Dishwasher Specifications
•
Product Weight – 98 Lbs.
•
Voltage Rating – 120V / 60 Hz
•
Connected Load (kW Rating) @ 120 Volts = 1.44 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
•
Amps @ 120 Volts = 9.0 Amps
•
Always consult local and national electric & plumbing codes.
Meets requirements of ASSE 1006.
•
Water Pressure – Hot water line to dishwasher must provide between
15 and 120 pounds per square inch (psi) with at least 120° F hot water
temperature.
•
Make sure location has correct drain, water and electrical outlets to make
connections.
•
Electrical and water supplies should enter cabinet opening on floor, or
through back or side walls, as shown in shaded areas.
•
Keep back free of drain, water & electrical supply.
•
Connections preferably located toward left side of dishwasher. Do not
cross drain, water or electrical lines in front of motor, blower or frame.
•
If connecting drain hose to sink trap, local code may require installation of
Air Gap Kit (not included).
•
Leveling legs supplied to adjust height. (Note: Height only adjustable to
35-3/4" max. when installed in 35-3/4" max. standard cabinetry cutout.
5/16" min. clearance required from top of unit to underside of countertop.
Dimensions do NOT include insulation — insulation blanket may be
compressed during installation.)
•
When installing adjacent to wall, cabinet or other obstruction that extends
beyond front edge of unit, allow 2" minimum clearance between opened
door and obstruction.
•
Floor should be flat and free of obstructions.
•
When installing at end of cabinet line, sides and back must be fully
enclosed.
•
Do not install unit under a cooktop, damage will occur.
•
Recommended to seal cabinets, enclosing all sides of dishwasher,
including underside of countertop, with oil-based paint or moisture-proof
polyurethane to prevent possible steam/moisture damage.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxicon.com for detailed instructions.
Built-In Dishwasher
E24ID75SPS professional series
Dishwasher E24ID75SPS
Electrolux ICON
Front
33
3
/4"
Adjustable
to 35
3
/4"
*
23
3
/4"
*Height only adjustable to 35
3
/4" max. when installed in 35
3
/4" max.
standard cabinetry cutout. (Dimensions do NOT include insulation –
insulation blanket may be compressed during installation.)
Left
24
1
/4"
Power supply & water inlet location
(bottom rear)
50
1
/4"
Right
Door in 90°
open position
27
3
/4"
22
1
/2"
3
1
/2"
min.
to
4
1
/2"
max.
1"
2
1
/4"2
1
/4"
**
NOTE: 35
3
/4"
max.
height for standard
cabinetry cutout.
(
5
/16"
min. clearance
required from unit to
underside of countertop.)
3"
18"
24"
min.
Electrical, water,
and drain
lines
must be confined
to shaded
area
1
1
/4"
24"
3
"
90°
90°
Preferred
drain areas
3
"
34"
min.
to
35
3
/4"
max.
**