Installation Built-In Instructions Coffee Maker Electrolux I ic o N TM E24CM75GSS E24CM76GSS 102221 REV.
Before You Begin READ THESE INSTRUCTIONS [] [] I m [] [] [] i [] [] [] [] [] [] [] [] [] [] [] [] [] [] NOTE Installer: Leave these instructions with the owner. Owner: Read your Coffee Maker Use and Care Guide completely before use. It contains important safety information for operating this appliance. It also has many suggestions for getting the best results from your coffee maker. Read all instructions before installing the coffee maker.
Finding Information TABLE OF CONTENTS [] [] [] [] [] [] [] [] [] [] [] Before You Begin ...................................................... 2 Finding Information ............................................... 3 Important Safety Instructions ........... 4 [] [] [] [] [] [] [] [] il [] [] Installation ............................................................... 10 Before You Start ..................................10 Tools Needed for Installation ...........
Safety IMPORTANT SAFETY INSTRUCTIONS [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] Safety Preca utions Do not attempt to install or operate this appliance until you read the safety precautions in this guide. Safety items throughout this guide are labeled with a Warning or Caution based on the risk type. Definitions j_ personal all safety It is messages that you follow to avoid This symbolinjury is thehazards. safety Obey alert symbol.
Safety ,,&WARNING To reduce the risk of fire, electrical shock, or injury when using maker, follow basic safety precautions including the following: Read all instructions IMPORTANT: that electric before operating Before performing power to the coffee IMPORTANT: the coffee coffee maker. any type of service or installation, make sure maker is disconnected.
Safety General Safety Precautions (continued) ,'&WARNING e Do not tamper with the controls. Clean the coffee maker thoroughly according to the Flushing Out the Coffee Maker section in the use and care guide before operating it for the first time. • When installing or cleaning the mechanical parts of the coffee exercise care with hands and arms around the metal edges. • Many metal surfaces behind the front panel and inside the brewing compartment are hot when power is on.
Preparing for Installation PLANNING THE LOCATION [] !1 II [] [] [] [] [] [] ! [] [] [] [] [] [] [] [] [] [] [] [] 4" X 12" J (100ram - 300ram) Ventilation Cut-Out in Cabinet Back i 24" J _lomm) 22 1/8"(582mm I 3/4" (19ram) 22 3/8" Steam Barner - 588mm) Min Side Walls 20 3/4" 3/4" 527mm ) 19mm) Level Support Platform \, _ 1/8" Opt imal Wa te r (3ram) and Electrical \\., Supply Location "-.
Preparing for Installation IMPORTANT: • DO NOT install the coffee maker in an unrestrained, free-standing cabinet. During normal operation, the user must have access to the top of the unit. The user needs to be able to pour coffee into the coffee bins on top and, on model E24CM75GSS, be able to remove the water tank for filling and cleaning. Install the coffee maker low enough so that the user can reach the top of the unit easily when it is slid out of the cabinet.
Preparing for Installation DIMENSIONS [] II [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] 22 1/16 (5&Ocrn) 18 3/16" (44.0cm) 17 9/16" (44.5crn) 18 3/16" (46.2crn) All tolerances: + 1/16", - 0" unless otherwise stated. TECHNICAL SPECIFICATIONS [] [] [] [] [] [] [] [] [] Power Requirements Total Connected !1 [] [] [] [] [] [] [] [] [] [] [] [] 120 Vac, 60Hz, 20A grounded, dedicated circuit required 1.
Installation BEFOREYOU START il [] [] [] [] [] il [] !1 [] [] [] Ii Remove the coffee maker from the packaging install a damaged maker. To prevent damage the appliance on the floor or counter II [] [] [] [] [] II [] [] and inspect it for damage. Do not to the control panel door, do not set prior to installation. Check to make sure all parts are included.
Installation TOOLS NEEDED FOR INSTALLATION [] [] [] [] [] [] [] • Phillips • Measuring • Level • Drill with 1/16" drill bit [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] I! [] screwdriver tape STEAM BARRIERINSTALLATION [] [] [] [] Position back Attach !! [] [] [] [] the steam barrier wall until the back it with the eight [] [] [] [] [] inside the top of the cut-out. edge lines up with (8) provided screws.
Installation PLUMBING INSTALLATION [] [] [] [] [] [] [] [] [] [] [] [] [] II [] [] [] [] [] [] [] [] CAUTION To prevent damage to the coffee maker due to hard water, prior to installation check the water hardness for the building where you will be installing the coffee maker. If necessary have a qualified water treatment specialist install a water treatment system. The water treatment system must be installed between the house plumbing and the coffee maker.
Installation To coffee maker To house water supply Filter head I t Everpure Filter Cartridge Electrolux ACCFILT-24 Filter Kit with Filter Installed 13
Installation INSTALLING THE CABINET GLIDES m I m [] [] [] [] [] [] [] [] [] [] B [] [] [] [] [] [] m [] The cabinet glides mount to the inside of the cabinet. The glides on the coffee maker slide into the cabinet glides. The guide system allows the coffee maker to slide in and out of the cabinet for loading the coffee bins and for maintenance.
Installation Put the two (2) cabinet glide assemblies, and shims if necessary, as shown on the inside surfaces of the cabinet. Position 4" (100mm) Cabinet Back Cutout for Circulati on them 3 1/2" (9.0cm) from the front edge of the cutout opening. Insert the screws in the holes of the glides without tightening them 3 1/2" completely. Make sure the outside distance between the 3 (9.0cm) fixing angles is 22 1/8" (56.2cm) and that the glides are level. Change the number of shims or 18" (45.
Installation INSTALLING THE UNIT IN THE CABINET [] m [] [] [] [] [] m [] m [] [] [] [] [] [] [] [] [] [] [] [] V'_ile supporting the coffee maker from below, insert it into the cabinet cutout. As you insert it into the cabinet, line up the glides on the appliance with the cabinet glides. The appliance should glide on the rails when slight pressure is applied to the front of the coffee maker. If it does not glide smoothly, check the distance between the glides again.
Installation CONNECTING THE PLUMBING (E24CM76GSS) [] [] [] [] II [] [] II [] [] [] [] [] [] [] [] [] [] [] !1 I! [] Z WARNING • To prevent damage to the coffee system due to hard water, installation, check the water hardness for the building be installing the coffee maker. See page 12 • To avoid leaks, do not overtighten Insert the 314" gasket it is properly seated. Connect maker. where you will fittings. into the 314" fitting on the water supply hose.
Installation VERIFYING OPERATION il [] [] [] [] [] In [] [] [] [] [] Ii II [] [] [] [] [] [] II z WARNING • Read the use and care guide • To keep the grinder from jamming, pour only coffee beans into the coffee bean container. Plug the coffee receptacle. completely maker into the dedicated, before operation. roasted, properly grounded, unflavored 3-prong power Test the lights by turning the light switch on and off.
Installation Troubleshooting 4. (Continued) Check the Solutions to Common Problems section of the use and care guide. Repeat the verification , 6. process. If the appliance still does not work, contact phone number inside the front cover.
Electrolux_ 1 - 877 - 4 Electrol ux www.elecLroluxusa.com www.electrol uxca.
