Use Care G u_a de Uso Guide d'utilJsation Guide y Cuidado et d'entretien
Thank you for choosing EJectrolux, the new premium brand in home appliances. This Use & Care Guide is part of our commitment to customer satisfaction and product quality throughout the service life of your new ice maker. We view your purchase as the beginning of a relationship. To ensure our ability to continue serving you, please use this page to record key product information. Once you have your unit installed, we suggest you keep this manual in a safe place for future reference.
information IPBODU BEG S ATION6£ [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] The package containing this manual also includes your product registration information. Warranty coverage begins at the time your Ebctrolux ice maker was purchased. Phase record the purchase address and tebphone Purchase Date date of your Electrolux unit and your dealer's name, number.
TABLE OIF'CONN [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] Finding Information ........................................... 2 PleaseReadAndSaveThis Guide ...................2 MakeA RecordForQuickReference................2 WarrantyRegistrationCard...............................3 Questions?........................................................ 3 TableOfContents.............................................. 4 Built-in Installation ..................................
IIM [] [] £NT S£F Y IINS U [] [] [] [] [] [] [] [] [] [] _ONS [] [] [] [] [] [] [] [] [] [] Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual. Safety items throughout this manual Danger, Warning or Caution based on the risk type. are labeled with a Definitions A This is the safety alert symbol. It is used to alert you to potential personal hazards.
GeneramPrecautions
IINSTAII,,,,,,,,,,_,,,,,,,,,,AT_ON D_MENS_ONS [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] (81) 34 = !/8" (86.7) FULL RETRACT HEIGHT WATER VALVE WATER DRAIN WATER OUTLET "_o 21 =3/4" (55.
THE £1N [] [] [] [] [] [] [] [] [] Model E151M60E can be installed or equivalent drain pump. [] [] [] [] [] [] [] [] [] [] using a gravity drain or can use a factory [] [] [] installed Follow these guidelines when installing drain lines to prevent water from flowing back into the ice maker storage bin and/or potentially flowing onto the floor causing water damage: GravityDrain • Drain lines must have a 5/8 inch inside diameter.
1 Make certain the unit is not plugged outlet. 2 Carefully push the power cord grommet in the back panel. See Figure 2. 3 Remove 4 Check that the clamps and hose connections the following areas illustrated in Figure 3: 12 screws Discharge into an electrical through BACK PANEL the hole DRAIN FiTTiNG and back panel. are tight at POWER CORD tube (A) ,, Drain tube (B) GROMMET ,, Vent tube (C) UL184=1 5 Place a suitable container beneath the pump's tube.
CONNE [] [] [] [] £ DR£11N PUMP [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] If a gravity drain connection is not availabb, and you have not purchased the E15JM60E with factory installed pump, we strongly recommend the use of the Eiectrolux EJMP60 drain pump. The Eiectrolux EIMP60 drain pump is available through your Dealer, or direct from Ebctrolux with compbte installation instructions.
IP PAB NGT [] [] [] [] m m SITE [] [] [] [] m [] m [] [] [] [] 1 Position the unit on a flat, level surface, capable of supporting weight of the unit. Remember that the unit will be significantly is fully loaded. 2 The surrounding exceed air temperature m m m m the entire heavier once it must be at least 50°F (10°C) but must not 110°F (43°C). 3 The unit must not be located near heat-generating sunlight.
0" CLEARANCE NEEDED UL124A Figure 4 WALL 2 * 3/4" CLEARANCE NEEDED Figure 5 EXHAUST Figure 6 _NTAKE 6 Install and connect the water supply line. See Connecting the Water Supply for installation requirements. 7 Position the unit to allow free air flow through front grille (see Figure 6). 8 Wipe out inside of unit with a damp cloth.
Whenconnectingthe water supply,follow theseguidelines: Reviewthe bcaUplumbingcodesbeforeyou instaUlthe unit. The waterpressureshouldbe between20 and120psi. Makecertaina SHUT-OFFVALVEis instaUled in the 1/4 inchwatersupplyHne. Connectsufficienttubingto the unitto allow the unitto be movedfor cleaningand servicing.However,makecertainthatthe tubing is not pinchedor damagedduring installation. WATER CONNECTmON Ebctrolux recommendsthe use of copper tubingfor installation.
Locate the compression fitting and ferrule packed in the unit. Slide the compression fitting and ferrule over the Figure8 1/4 inch water supply line. Do not use thread sealing compound or tape. Using two wrenches, tighten the compression fitting on the supply line (see Figure 8). \ Carefully bend the water supply line into position and connect the line to the solenoid valve (see Figure 9). Avoid kinking the water supply line. % .
IILEV [] [] m T m m UNiT m [] [] [] [] [] [] m [] [] [] [] m [] m m [] Use a ReveUto check the ReveUness of the ice maker from front to back and from side to side (see Figure 11). tf the ice maker is not bveU, adjust the feet on the corners of the unit as necessary (see Figure 12).
REVERSINGTHE BOOR(SOMEMO [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] ILLS} [] [] [] [] [] [] AH EbctroUux units may be bft or right hand opening. The door opening is easily reversed by moving the hinge hard-ware to the opposite side (see Figure 13). To reverse the door: 1 Remove top hinge screw pin (7/64" AUUenwrench) from cabinet (see Figure 14). Remove door by tilting forward and Rifting off bottom hinge pin. 2 Remove \ Figure 13 pUastb screw plugs (3 top and 3 bottom) from ne
HINGE SCREW PiN Remove remount top hinge (3 screws), reinstall hinge screw pin, and on opposite side BOTTOM (see Figure 17). Remove the two door cioser inserts from the existing bottom hinge and instali as shown on the new bottom hinge (see Figure Remove opposite _"_ I I _=_ i Figure 17 18). existing bottom hinge (3 screws) and remount side TOP. Remove hinge screw pin.
£DJUST NGTHEOB [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] Your door is aligned at the factory before shipment. OccasionaU re=adjustment may be necessary, especially if an overlay paneU is installed. The following procedure will correct for up to 1/4" alignment. The door shouUd never be flush with the top of the cabinet. Even when bveU, the top edge of the door wiIR be 1/8" below the top of the cabinet (see Figure 21).
4 tf door edge opposite the Nnges needs to move up, move plate toward outside of door. tf door edge needs to move down, move plate toward inside of door (see Figure 23). Repeat until top edge of door is parallel with top of cabinet screws securely. 5 MOUNTING _ IS NOTCH and tighten After adjustment is complete, remove the door closers from the bottom hinge, clean thoroughly and apply petroleum jelly to the mating surfaces of the closers (see Figure 24).
£ [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] Your Electrolux product has been designed for either free-standing or built4n installation. When built=in, your ice maker does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed.
IINmAL,,,,,A [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] Once installation and leveling is complete, the unit is ready for initial start-up and operation. Your unit is shipped in the OFF position, however, you may turn it ON/ OFF using the cycle selector switch located in the access panel above the grille (see Figure 26). 1 PRug the appliance grounded electrical cord into a 115V polarized Figure 26 and outlet.
NORMAILOPER£T ON [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] The ice maker is designed to make clear ice from most water sources on a consistent basis. Water is constantly circulated over the evaporator assembly. As the water freezes, gravity causes any sediment to drop into the water trough and not become imbedded in the ice. This gives a clearer ice cube with a low mineral content.
liCEDISPENSEROPERATION& CARE [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] The be cube thbkness control is factory set for best overall performance. The factory setting is designed to maintain an be bridge of Figure 28 approximately 1/16" to 1/8" under BRIDGE normal conditions resulting in a TOO THIN 1/16" TO 1/8" DIMPLE _\ ICE BRIDGE dimple of approximately 1/4" to 1/2" TOO DEEP \\ in depth (see Figure 28).
3 Locate the ice cube thickness adjustment dial on the control board (see Figure 30). Turn the dial clockwise (+ number) or counterclockwise (- number) to thin the ice bridge. Figure 30 I DIAL IS FACTORY SET AT"O" ICE CUBE THICKNESS ADJUSTMENT DIAL _!i !!_i_i!i!_i_i!ii!_i_!_!_i_i!!i!_i!;_i_i!_!i!i!i_!_ !iiiii!iiii !iiiii!iiii !iiiii!iiii !iiiii!iiii !iiiii!iiii !iiiii!iiii !iiiii!iiii!iiiiiii! Reinstall Ice Cube Mold SAMPLE cover.
SPECiAl,,,,,,,,,, CONSDERATIONS [] [] [] [] [] [] [] [] For best performance, [] [] [] [] [] [] [] [] [] [] [] [] [] [] keep the unit out of direct sunlight. Turn the unit OFF and dispose of any be cubes if the unit will not be used for 5 days or more. Prop door open to allow for air circulation and prevent mold and mildew. tf the ambbnt temperature is expected to drop below 45°F (7°C), drain all water from the unit to prevent freezing damage not covered by the warranty.
® DO NOT CLEAN WITH o DO NOT USE CLEANERS STAINLESS STEEL WOOL THATARE STEEL (this includes PADS. NOT SPECIFICALLY glass, tile and counter INTENDED FOR cleansers). tf any surface discolors or rusting appears, clean it quickly with Bon-Ami or Barkeepers Friend Cleanser and a non-abrasive cloth. Always clean in the direction of the grain. Always finish this process with a high quality, aINn-one stainless steel cleaner/polish to prevent further problems.
CondenserCleaning-- Every3 Months To maintain operational efficiency, clean the condenser every three months (depending on environmental conditions, more or less frequent cleaning may be necessary). To remove and replace the grille for access to the condenser Figure 32): 1 Remove fins follow this procedure the screws (see at each end of the grille. 2 Remove CONDENSER the grille. Figure 32 Clean the condenser coil using a brush with a "combing" cleaner. Do not touch the condenser coil.
Sdf Cleaning-- Every6 Months To maintain operational efficiency, clean the unit every six months (depending on water conditions more or lees frequent cleaning may be necessary), if the ice maker requires more frequent cleaning, consult a qualified plumber to test the water quality and recommend appropriate treatment. Ice machine cleaner is used to remove lime scale and other mineral Refer to the following steps for mineral deposit removal. J / F FRONT COVER Figure 33 deposits.
Removethe overflowtubeby liftingit upwhileusinga slightbackandforth motionto loosenit fromthe drain hole (see Figure 34).The water inthe reservoirwill flow downthe drain. Replacethe overflowtube afterall ofthe waterhas drainedfromthe reservoir. 6 Movethe cycleselectorswitchto the CLNposition. 7 Whenwaterbeginsto flow overthe evaporator (approximately3 minutes),addonepackageof Electrolux ice MacNneCleanerto the waterreservoir. 8 Reinstallinsidefrontcover.
DBABNBNG IB:'":'OR NON@SE [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] If the unit is to be stored, moved or not used for extended necessary to drain the system of water. 1 Disconnect 2 Remove 3 Shut off water supply at the main water source. 4 Disconnect [] [] periods, [] [] [] it will be power from the unit. ice from the storage bin. the inlet and outlet lines to the water valve and allow them to drain. 5 Reconnect inlet and outlet lines to the water valve.
BEFOREYOU CALL FORSERVICE [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] tf the unit appears to be malfunctioning, read through Normal problem persbts, check the Troubleshooting Guide. Locate guide and refer to the cause and its remedy before calling for could be sometNng very simpb whbh can be solved without Troubleshooting [] [] [] [] [] Operation first. If the the problem in the servbe. The problem a servbe call.
Troubleshooting - What to check when problems occur Problem PossibleCause Remedy Poor icequality(softor unclear). • Poorincomingwaterquality. • Consulta qualifiedplumberto test the water qualityand recommendappropriatetreatment. • Ice-makingsystemis dirty. • Rununitthreughautomaticcleancycle.See Maintenance. • Lowwater level. • Checkto see thatoverflowtube isfullyseated. • Hot incomingwater. • Connectthe unit to a coldwater supply.See Installation. • Incorrectincomingwater pressure.
ICEMAKER WARRANTYYourice maker is protected by this warranty WARRANTY PERIOD FULLONE-YEAR WARRANTY Oneyearfrom originalpurchase date. THROUGH OURAUTHORIZED SERVICERS, WEWILL: THECONSUMER WILLBE RESPONSIBLE FOR: Payallcostsforrepairing or replacinganypartsofthis appliance whichprovetobedefective in materials or workmanship. Costsofservicecallsthatarelistedunder NORMALRESPONSIBILITIES OFTHE CONSUMER,* LIMITED 2"d-5TM Secondthrough fifth YEARWARRANTY yearsfromoriginal (CabinetLinerand purchase date.
