I N S T RU C T I O N B O O K CHIMNEY HOOD CH60 and CH90 cod.
Thank you for buying an Electrolux product. To enable you to use your application effectively and safely, please read this instruction book carefully before using the appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on Electrolux Products, please contact our Customer Care Department.
IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of safety. Ensure that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. • • Installation • This hood must be installed in accordance with the installation instructions and all measurements must be adhered to.
YOUR APPLIANCE OPERATING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. Cooker Hood Controls The cooker hood functions are controlled by three switches located to the right on the underside of the hood immediately in front of the metal grease filters. Worktop Lighting The switch (L) marked with the lamp symbol operates the worktop lighting.
To Operate Select the required fan speed and light if required. The appliance can be installed to recirculate or extract contaminated air. The cooker hood is more effective when used in the extraction mode. Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted.
MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean, as a build up of grease or fat can be a fire hazard. External Cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent. Never use scouring pads or abrasive cleaners. Never use excessive amounts of water when cleaning particularly around the control panel.
Charcoal Filters In the recirculation mode the charcoal filters absorb smells and unwanted odours. The charcoal filters cannot be cleaned, we recommend they should be replaced approximately every three months or more often if the hood is used for more than three hours per day. To Remove/Replace the Charcoal Filters 1. First remove the metal grease filters as illustrated in Fig. 1. 2. Rotate the charcoal filter anticlockwise (B) and remove illustrated in Fig. 2. 3.
SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom Solution The cooker hood will not start • Check the hood is connected to the electricity supply. • Make sure the switch is in the ‘ON’ position. The cooker hood is not working effectively • The fan speed is set high enough for the task • The grease filter is clean. • The kitchen is adequately vented to allow the entry of fresh air.
GUARANTEE CONDITIONS We, Electrolux, undertake that if within twelve months of the date of the purchase this Electrolux built-in product or any part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electrical supply stated on the rating plate.
INSTALLATION INSTRUCTIONS Technical information DIMENSIONS HEIGHT OF CANOPY: HEIGHT OF CHIMNEY:(UPPER SECTION) (LOWER SECTION) WIDTH OF CANOPY: CH 60 CH 90 DEPTH OF CANOPY: 270mm 215mm 530mm 598mm 898mm 490mm ELECTRICAL SUPPLY VOLTAGE: (~50Hz) POWER CONSUMPTION: FAN MOTOR: LAMPS: (2 x40W) 220-240V 225W 145W 80W ELECTRIC HOB: GAS HOB: SLOT-IN ELECTRIC COOKER: SLOT-IN GAS COOKER: 7KW (MAX) 10KW (MAX) 12.4KW (MAX) 13.
INSTALLING THE COOKER HOOD 2 S 1 I A C R D B (Optional Splashback B) Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. The manufacturer disclaims any responsibility for damage due to incorrect installation of the cooker hood or if the hood is not installed in compliance with relevant regulations controlling this type of installation.
Clearance Heights The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, providing the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications. If the output of the appliance below the cooker hood exceeds the maximum outputs quoted, please refer to the cooker manufacturer’s installation instructions.
3. Fixing the first wall bracket No 2 Draw a horizontal line through the vertical at 15mm from the ceiling as illustrated, or from a horizontal line drawn between the top of two adjoining wall cabinets. Place the top edge of the bracket against the line, aligning the centre of the bracket with the vertical line. If, the alignment is correct mark the centres for the keyhole fixing screws (not supplied) as illustrated in Fig. 3. 4.
Fitting the Canopy Hood 1. Adjust the two screws V on the top of the canopy to about halfway as illustrated in Fig. 5. 2. Hook the canopy onto the wall bracket 1 and push down until the canopy adjusting screws V rest on the bracket, turn the screws to adjust the canopy vertically and level it horizontally as illustrated in Fig. 5. 4. Insert the screw V1 into the central hole to lock the canopy in to position as illustrated in Fig. 5. Fig.
Extraction The charcoal filters are not required in this mode and should be removed. Ducting The ducting used must be 150mm (6ins), or 125mm (5ins) in diameter. If possible duct through the wall immediately above the canopy. For the best performance use the shortest possible duct run and the minimum number of bends. Where flexible ducting is fitted it should not be turned through very tight bends as this may impair the performance of the hood.
Fitting the Chimney Stack The chimney consists of two sections. The upper chimney measures 215mm and the lower chimney (with the holes for recirculation on either side) measures 530mm. 1. Fit the two plastic supports provided into the two holes on top of the canopy as illustrated in Fig. 7. 2. Fit the upper section (S) first.
55 - 77 High Street - Slough BERKSHIRE SL1 1DZ © Electrolux plc 2002
