L)) Important User Information 1T 1S MOST IMPORTANT THAT THIS INSTRUCTION BOOK SHOULD BE RETAINED WITH THE APPLIANCE FOR FUTURE REFERENCE. SHOULD THE APPLIANCE BE SOLD OR TRANSFERRED TO ANOTHER OWNER, OR SHOULD YOU MOVE HOUSE AND LEAVE THE APPLIANCE, ALWAYS ENSURE THAT THE BOOK IS SUPPLIED WITH THE APPLIANCE IN ORDER THAT THE NEW OWNER CAN BE ACQUAINTED WITH THE FUNCTIONING OF THE APPLIANCE AND THE RELEVANT WARNINGS.
. » When replacing the upper rack, do not forget to relocate the spats and side the cover up over the water quot that feeds the upper spray arm. Heavy ferns such as large plates and dishes should be placed in the lower dish rack, The fighters should be checked for clogging after each wash, They rust always be replaced in the correct position after cleaning The dish racks should be pulled forward gently on their wheels for loading.
Welcome to the family of Electrolyte Users. You are now the proud owner date dishwasher that will make the repetitive chore of washing up so much easier. This book not only tells you how to operate your new Electrolyte dishwasher but includes instructions on how to install it properly.
installation In order that your new dishwasher will operate correctly and give yol tha best possible results it must be stalled in accordance with the following instructions. Any local regulations concerning connections 1o the electricity and water supplies and drainage must also be complied with, Location The dishwasher can be placed in any suitable position providing the water, drain and electrical connections are accessible.
As a General Guide ta Fitting any Plug Ensure the lengths of wire inside the plug are prepared correctly. Connections should be firmly made after a conductor strands are entered int the terminal posts. . When preparing the cable ends take care notch damage the outer sheath, or the insulation surrounding the infer conductors. Tighten all screws, Replace the top cover of the plug and secure.
Inlet water connection The dishwasher may be constricted either to hot or cold water supply but not both, T MUST NEVER BE CONNECTED TO A MIXER TAP. The pressure of the water supply should be between 80 KN/m? 1000 kn? {12 145 b/ in?} and the temperature should not exceed 20°C130°F. If you connect your dishwasher to the hot water supply you must remember that all fills wilt be with hot water and this could mean a tonal hat water consumption of 28 fires {6 legalism. The water inlet hose has a %" BSP.
Getting to know your Dishwasher This section is designed to help you became familiar with the various features of your new dishwasher. 1. Programmer Selector Buttons Push the relevant Programmer Selector Burton in 1o select any of the basic programmers, The indicator tamps (4] will illuminate when the programmer is selected o indicate the phases through which the cycle will pass. As the cycle progresses the lamps will go out indicating each completed stage. 2.
replacing the rack don't forget to relocate the: stops. The upper dish rack can be left out when washing buff items in the lower dish rack, but remember you must slide the cover up over the water outlet that feeds the upper spray arm {14}. The rack has 2 hinged flaps {10} thatcher fitted either side of ihe basket. When lowered they serve as extra racks for cups, 11. Lower Dish Rack The lower dish rack is for heavier items such s large plates and dishes.
should be checked after every wash. Removing the coarse fighter additionally allows removal of the fine filter {21}, Although thesis a self cleaning fitter it oldish be checked occasionally and rinsed under the tap, paying particular attention fo the underside. DO NOT FORGET Y0 PUT BOTH FILTERS BACK AFTER CLEANING AND MAKE SURE THEY ARE IN THE CORRECT POSITIONS. 22.
Remember the rinse-aid container should airways be refilled before it is completely empty, Filling the salt container for the water softener Remove the lower dish rack to give access to the sat container filler cap and unscrew the cap. Having removed the cap, place a funnel! over the opening and pour in about water softener granular or regeneration salt. Available from larger hardware stores or builders merchants.
Using your Dishwasher 1. Scrape plates clean of fare paces of waste food, buns, etc. 2. Loading ‘The dish racks should be pulled forward gently on their wheels to make the racks more accessible for loading. Typical loading for sate of the racks are shown in the Frustration on Page 9.The upper dish rack is for cups, saucers, glassware, small plates and bowls, etc. Cups, glasses and bowls should be placed upside down.
8, After the wash Her the washing programmer has finished, the making will stop. You should then switch off the machine, and also turn off the water supply stopcock. Do not furs off the water before the programmer has finished, as water is needed for the regeneration of the water softener which takes place during the drying cycle, Finally, remember to inspect the filters occasionally and, i necessary, rinse them under 2 tap. Note that there may be a small amount of water left in the filter recess. 9.
Useful Information Generally speaking, crockery and cutlery which can normally be washed by hand can also be washed in the machine, although pans, casserole dishes, enc, which have food burnt on, cannot always be expected to be completely clean, Some materials are not suitable for machine washing, or require special treatment, therefore, o avoid any disappointment, we suggest the following information is carefully studied % Some plastics are suitable for washing in the high water temperatures obtained in th
What too and when in the event of your machine developing a fault, you should quickly run through this check fist before calling your coal Electrolyte Service Reception Unit. I your wash is not satisfactory. 1. Check that the crockery or cutlery has been properly loaded. 2. Check that the spray arms, or holes in the arms, have not become obstructed or Blocked Check that the filter is clean. . Check that the programmer selected was the correct one. 5. Check that the correct amount of detergent was used. 6.
GEIGER CENTERS é&; S SOUTHERN DIVISION Bristol 0272 211878 Cardiff 0222 460131 Alder shot 0252 24505 Brighton 0273 694341 Convey stand 0268 694144 Newton Abbot 0626 65909 Portsmouth 0704 667411 Ton bridge 0732 357722 LONDON & EASTERN DIVISION Latin 0582 576966 Norwich 0603 667017 London (North) 03 884 2284 London {South) 01 658 9069 London (West} 01 965 9699 Oxford 0993 4411 NORTHERN DIVISION Birmingham 021 358 7076 Gates head 091 460 0440 Manchester 061 798 9689 Leeds 0532 608511 Leicester 0533 515131 Live
Fitting a Decor Panel Model BW3200FD is supplied in white with decor frame around the main door and lower panel. To fit the panels proceed as follows: 1. Remove the 3 screws on each side and lower edge of the door. Remove the decor frames. Place the decor panel in position. Replace the frames. 2. Remove the screws from the lower panel. 3. Remove the old decor panel if fitted. If the new panel is 4mm thick, remove all four pasteboard fillers; if 2mm thick, remove only 2 fillers, 4.
