Technical data
Table Of Contents
- III. INSTRUctions FOR USE 41
- 1. Opening the oven door 41
- 1.1 6- and 10-grid models 41
- 1.2 20-grid models 41
- 2. Closing the oven door 41
- 2.1 6- and 10-grid models 41
- 2.2 20-grid models 41
- 3. Description of the control panel 42
- 3.1 Introduction 42
- 3.2 Main controls 42
- 3.3 Main cooking modes 42
- 3.4 Special cooking modes 42
- 3.5 Additional functions 42
- USING THE OVEN 44
- 4. Operating level A, B and C 44
- 4.1 Switching the oven on 44
- 4.2 Selecting the controls 44
- 4.3 Manual controls 44
- 4.4 Automatic controls 48
- 5. Information and error codes 51
- 6. Switching off in the event of a fault 52
- 7. Care and maintenance 52
- 7.1 Periodic maintenance of the boiler 53
- 7.2 Replacing consumable components 54
- 7.3 Special cleaning instructions 54
36
GB
5938 034 01
E
C
ø D
2D
A
G
*
Tmax=350°C
SILICONE
B
A
G
Tmax=350°C
3 meters MAX
*
SILICONE
C
E
B
CONSTRUCTION TYPE
B13
1b
DISCHARGE WITH SHROUD UNDER EXTRACTOR HOOD
CONSTRUCTION TYPE
B13
1c
DISCHARGE TO THE OUTSIDE OR CENTRAL FLUE WITH SHROUD
LEGENDA:
A: Cam / draught damper accessory
(to be ordered from manufacturer)
B: Boiler combusted gas discharge
C: Oven chamber convector combusted gas discharge
E: Adapter ring for commercial ducts
(to be ordered from manufacturer)
F: Conical connections for single outlet (supplied)
(always install)
G: Fixing screws (supplied);
*: Commercial extension pipes (not supplied)
SILICONE :
Apply silicone sealant between contact surfaces
power supply with an H05 RN-F type cable. The power supply
cable must be protected by a metal or rigid plastic conduit. If the
If the appliance is connected by way of an existing lead, do not
insert the cable conduit into the appliance and make particularly
sure that the conduit has no sharp edges.
• The appliance must be suitably earthed. The earthing conductor
must therefore be connected to the terminal marked G on the
connection terminal board. The appliance must also be connected
to an earth bonding system.
This connection is made using the stop screw marked E located
on the outside of the appliance near the power cable inlet.
The bonding wire must have a minimum cross-section of 10 mm
2
.
4.1 INSTALLING THE POWER SUPPLY CABLE
To access the power supply cable connection terminal board,
proceed as follows:
Model 6 - 10 - 20 GN
• Remove the left side panel.
• Connect the power supply cable to the terminal board according
to the instructions given in the wiring diagram and fasten the
power supply cable by means of the cable clamp.
The manufacturer declines all responsibility if the applicable
safety regulations are disregarded.
5. WATER MAINS CONNECTION
(Refer to the installation diagrams at the beginning of this booklet).
When connecting the appliance to the water system with
flexible tubes they must be new and not used.
The appliance is fitted with two separate water inlets ("B" and "N").
The water lines supplying both inlets must be fitted with a
mechanical filter and shut-off cock.
Before fitting the filters allow the water to flow out for sufficient time
to flush any solid particles from the piping.
Pressure between 150 and 450 kPa (1.5-4.5 bar).
WATER INLET “N”
Attention (water inlet N)
If the supply pipes provided with the appliance are not long
enough for installation, use longer ones with int. diameter at
least ø 20 mm and free of elbow unions.
Note:
To check correct water installation, make sure the rotating wash
arm (CLEANING SYSTEM) does not turn below 100 rpm (120
max).
The appliance must be connected to the mains power supply
in compliance with current regulations.
• Before connecting the appliance to the mains supply, make sure
that the voltage and frequency shown on the appliance identification
dataplate correspond with those of the power supply.
• The appliance must be permanently connected to the mains