Operators Manual, Super Tilematic G2, 2005-04, 542 20 10-38 Super Tilematic G2 STM 10100 G2 STM 10100SS G2 Operator’s manual Read these instructions carefully and make sure you understand them before using the TARGET Tilematic G2. Manual de Instrucciones Antes de utilizar TARGET Tilematic G2 lea bien el manual de instrucciones hasta comprender su contendo. Manuel d’utilisation Lire attentivement et bien assimiler le manuel d’utilisation avant de se servir TARGET Tilematic G2.
EVERY MACHINE IS THOROUGHLY TESTED BEFORE LEAVING THE FACTORY. EACH MACHINE IS SUPPLIED WITH A COPY OF THIS MANUAL. OPERATORS OF THIS EQUIPMENT MUST READ AND BE FAMILIAR WITH THE SAFETY WARNINGS. FAILURE TO OBEY WARNINGS MAY RESULT IN INJURY OR DEATH. FOLLOW INSTRUCTIONS STRICTLY TO ENSURE LONG SERVICE IN NORMAL OPERATION. CONTENTS Symbol Definitions .................................................................................................................................................
Symbol Definitions Symboles Definición De Los Simbolos • • • Please read the instructions for use prior to operating the machine for the first time. Avant toute mise en service, lire attentivement la notice et se familiariser avec la machine. Antes de la puesta en marcha, lea detenidamente las instrucciones y familiaricese con la máquina.
• • • Motor Off Arrêt Du Moteur Parar El Motor • • • Use In Well Ventilated Area A Utiliser Dans Un Endroit Bien Ventilé Usar En Una Área Bien Ventilada • • • Do Not Use In Flammable Areas Ne Pas Utiliser Dans Des Ambiances Comportant Un Risque D’incendie No Usar In Áreas Inflamables • • • Machinery Hazard, Keep Hands And Feet Clear.
• • • Repairs Are To Be Done By An Authorized Dealer Only Les réparations ne peuvent être exécutées que par un distributeur agréé Las Reparaciones Deben Ser Efectuadas Únicamente Por Un Distribuidor Autorizado • • • Diamond Blade Disque diamanté Sierra Diamantada • • • Blade Diameter Diamètre De Disque Diámetro De La Hoja • • • Pulley Diameter Diamètre De Poulie Diámetro De La Correa • • • Number of Revolutions Per Minute, Rotational Speed Nombre De Tours/Minutes, Vitesse De Rotation N° De Revoluci
DECAL DESCRIPTIONS & LOCATION P/N 542 18 70-43* Location: Top of Belt Guard P/N 542 04 63-26* Location: Motor Assembly 6 P/N 542 18 92-47* Location: Elec.
DECAL DESCRIPTIONS & LOCATION P/N 542 20 30-64 Location: Both Sides of Pan P/N 542 18 97-36* Location: Front of Pan P/N 542 18 97-31* Location: Blade Guard & Belt Guard P/N 542 18 76-91* Location: Belt Guard Top 7
SAFETY FIRST! WARNINGS DO’s AND DO NOT’s WARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY. DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO 8 read this entire operator’s manual before operating this machine. Understand all warnings, instructions, and controls. keep all guards in place and in good condition.
SAFETY FIRST! WARNINGS DO’s AND DO NOT’s WARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY. DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT operate this machine unless you have read and understood this operator’s manual.
FIGURE 1 5 E I O F J K G L H M2 1 4 M1 R 3 A B N 2 D Q P C A. Set Collars (See Fig. 2 for Plunge Cutting Components) 1. Cutting Head Assembly: Includes water tube assembly (H)} B. Bearing Cap 2. Frame Assembly C. Locking Knob 3. Water Pan Assembly D. Lockbar 4. E. Water Pump Conveyor Cart Assembly Carton {Cart Assembly (4) and Rip Guide (R)} F. Hose Barb 5. G. Water Valve H. Water Tube Assembly I.
MANDATORY INSTRUCTION INDICATION INFORMATION Use only blades marked with a maximum operating speed greater than the blade shaft speed. PROHIBITION WARNING Before starting up the machine, make sure you read this entire manual and are familiar with the operation of this machine. These signs will give advice for your safety The working area must be completely clear, well lit and all safety hazards removed. Before leaving our factory every machine is thoroughly tested.
mended that the tubing and electrical cord exit out the back through the indented area of the pan. 5. Insert the male plug into the Receptacle (O) on the motor. The Water Pump (E) will start when the motor is turned on. For dry cutting, the water pump should be unplugged or removed to prevent damage to the pump. NOTE: THE MOTOR WATER PUMP OUTLET IS NOT TO BE USED AS A GENERAL PURPOSE CONVENIENCE OUTLET. USE FOR CONNECTION OF THE SUPPLIED WATER PUMP ONLY. 5.
5. 6. • Install the Outer Flange (M2) with the large diameter against the Blade (K). Tighten the Blade Shaft Nut (L) with the 15/16" Wrench (N) provided. Lower the Blade Guard (J) and retighten the wing nut to securely hold the guard in place. Install the Drain Plug (P) into the front end of the pan and fill with clean water until inlet filter of water pump is covered; about 6.5 gal. (25 l).
The Tilematic is shipped standard set-up for a 10” diameter blade. To change the setting, locate the capscrew (23) used as the pivot, loosen and remove the Lock Nut. Set the Lockbar ( 28) at the proper hole for blade size. Tighten the fasteners so that the Lockbar (28) is free to pivot. Check the setting by loosening the Knob (26) and lowering the head fully down into the table slot. The blade segment should be below the table surface, but not cutting into the table. (See also Section 10, Plunge Cutting.
• • • been installed. (Refer to Section 5, Adjustable Lockbar, if needed) Install the profile wheel onto the spindle shaft up against the inner flange with the working surface to the outside. Secure into place by reversing the outer flange and tightening the spindle nut. Lower the Blade Guard (J) back down over the profile wheel. Locate the material for profiling: 1. Set the edge of the part to be shaped parallel to the wheel. 2. Locate the material under the wheel.
15 TILE CUTTING ACCESSORIES ANGLE GUIDE PROTRACTOR MITY MITRE GUIDE BULLNOSE FOLDING STAND Parts List: Diag. 1 2 3 4 5 6 7 8 9 Part No. 542 05 01-04* 542 05 01-07* 542 05 01-05* 542 05 01-06* 542 05 01-03* 542 18 97-37* 542 05 10-20* 542 18 97-37* N/A Qty. 1 1 1 1 1 2 1 1 1 Description Frame, Miter Bar, Locking Clip, Stop Spring Knob Knob, 1/4"-20 x 1" Miter Assy, 45° Knob, 1/4"-20 x 1" Sector Plate Diag.
Diagram 1: Wiring Diagram 542 20 30-79, 1.
Diagram 2: Wiring Diagram 542 00 06-05, 1.
Target’s Gold Medal Equipment Warranty New equipment sold by Target is warranted to be free from manufacturing defects in normal service for a period of two (2) years from date of purchase by the original consumer purchaser. Component manufacturers offer separatewarranty periods. Call Technical Serives at 800-288-5040 for complete information.
Target Corporate Office 17400 West 119th Street Olathe, Kansas 66061 Customer Service: 800-288-5040 Customer Serv. Fax: 800-825-0028 Corporate Office: 913-928-1000 Corp. Office Fax: 913-438-7951 Target California Customer Service: 310-381-3100 Customer Serv. Fax: 310-381-3194 Target Canada Customer Service: 800-461-9589 Customer Serv. Fax: 800-728-1907 Target International Customer Service: 913-928-1300 Customer Serv.
