Datasheet

ManualsBrandsElectrolube ManualsChemicalsClear Protective Lacquer Spray 200 ml

Page 1

CPL

Clear Protective Lacquer

CPL is a general purpose coating designed to protect printed circuit boards from environmental attack. The high

gloss properties of CPL also make it an ideal choice for over-coating applications where cosmetic appearances

are a contributing factor. It is also suited for protecting ferrous metals from corrosion.

• High quality gloss finish; ideal for over-coating applications

• Cost effective coating with good resistance to humidity

• Does not contain a UV trace

• Suitable for applications requiring rework; cured coating can be removed with Electrolube ULS

Approvals RoHS-2 Compliant (2011/65/EU): Yes

NATO Stock Numbers: 8010998020506 (CPL05L)

8010997774491 (CPL200H)

Liquid Properties Appearance: Clear Pale Straw

Density @ 20°C (g/ml): 0.86 (Bulk), 0.79 (Aerosol)

VOC Content: 79%

Flash Point: 12°C

Solids content: 21%

Viscosity @ 20°C (mPa s): 25

Touch Dry: 15-20 minutes

Recommended Drying Time: 24 Hours @ 20°C

Coverage @ 25µm: 7m

per litre (Bulk), 1.3m

(200 ml Aerosol)

Dry Film Coating Colour: Colourless (High Gloss)

Operating Temperature Range: -50°C to +100°C

Flammability: Meets UL94 HB

Thermal Cycling (MIL-1-46058C): Meets approval

Coefficient of Expansion: 140ppm

Dielectric Strength: 45 kV/mm

Dielectric Constant: 3.5

Surface Insulation Resistance: 1 x 10

Ω

Dissipation Factor @ 1MHz @ 25°C: 0.01

Moisture Resistance (MIL-1-46058C): Meets approval

Summary of content (4 pages)

PAGE 1
Page 1 CPL Clear Protective Lacquer CPL is a general purpose coating designed to protect printed circuit boards from environmental attack. The high gloss properties of CPL also make it an ideal choice for over-coating applications where cosmetic appearances are a contributing factor. It is also suited for protecting ferrous metals from corrosion.
PAGE 2
Page 2 Description Packaging Order Code Shelf Life CPL Conformal Coating 200ml Aerosol 5 Litre Bulk CPL200H CPL05L 36 Months 48 Months Conformal Coating Thinners 1 Litre 5 Litre Bulk DCT01L DCT05L 36 Months 36 Months Removal Solvent 200ml Aerosol 400ml Aerosol 1 Litre Bulk 5 Litre Bulk 25 Litre Bulk ULS200D ULS400D ULS01L ULS05L ULS25L 36 Months 36 Months 72 Months 72 Months 72 Months Directions for Use CPL can be sprayed, dipped or brushed.
PAGE 3
Page 3 Viscosity Change with Temperature - CPL 35 Viscosity (mPa s) 30 25 20 15 10 5 0 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Temperature (⁰C) Spraying - Aerosol When applying CPL in aerosol form care must be taken to ensure the can is not shaken before use. Shaking the can will introduce excessive air bubbles and will give a poor coating finish. The can should be held at 45° and 200mm from the substrate to be coated.
PAGE 4
Page 4 The board assemblies should be immersed in the CPL dipping tank in the vertical position, or at an angle as close to the vertical as possible. Connectors should not be immersed in the liquid unless they are very carefully masked. Electrolube Peelable Coating Masks (PCM/PCS) are ideal for this application. Leave submerged for approximately 10 seconds until the air bubbles have dispersed. The board or boards should then be withdrawn slowly (1 to 2 s/mm) so that an even film covers the surface.