System information
X-Array Touring Loudspeaker Systems – Applications Notes – Page 21
Xb, Xn & Xn - Mono (Also for Xcb & Xcn): This program should be used with the Xb and Xn loud-
speaker systems for mono, short/mid-throw applications where multiple coverage zones are employed
(two per DN8000). Typical applications would include near-field systems in large front-of-house systems,
small front-of-house systems, side-fill, down-fill and front-fill systems. Xcb systems may be substituted for
the Xb systems and Xcn systems may be substituted for the Xn MB and HF sections using these same
DN8000 settings. The Xb and Xn LF sections share the same drive signal (although the Xn LF amplifier
channels must be turned down 6 dB). This program is included as a DN8000 factory preset.
Xb, Xn & Xn - Stereo: This program should be used with the Xb and Xn loudspeaker systems for stereo,
short/mid-throw applications. Typical applications would include small front-of-house systems, side-fill
and front-fill systems. Xcb systems may be substituted for the Xb systems and Xcn systems may be sub-
stituted for the Xn MB and HF sections using these same DN8000 settings. The Xb and Xn LF sections
share the same drive signal (although the Xn LF amplifier channels must be turned down 6 dB). This
program is included as a DN8000 factory preset.
Xn & Xds - Mono: This program should be used with the Xn and Xds loudspeaker systems for mono,
short/mid-throw applications with subwoofers, but without additional (Xb or Xcb) bass systems. Typical
applications would include small front-of-house systems, side-fill and front-fill systems. This program is
not included as a factory preset and must be manually programmed into the DN8000 by the user.
Xn - Stereo: This program should be used with the Xn loudspeaker systems in stereo, short/mid-throw
applications without additional low-frequency systems. Typical applications would include small front-of-
house systems, side-fill, down-fill and front-fill systems. This program is not included as a factory preset
and must be manually programmed into the DN8000 by the user.
Xb, Xf & Xn - Mono: This program should be used with the Xb, Xf and Xn loudspeaker systems for
mono, combination long- and short/mid-throw applications. Typical applications would include front-of-
house systems and large-stage side-fill systems. Xcb systems may be substituted for the Xb systems
and Xcn systems may be substituted for the Xn MB and HF sections using these same DN8000 settings.
The Xb and Xn LF sections share the same drive signal (although the Xn LF amplifier channels must be
turned down 6 dB). This program is included as a DN8000 factory preset.
Xds - Mono Sum: This program should be used for adding mono-summed Xds subwoofer systems to
any of the full-range systems included on this list. This program is not included as a factory preset and
must be manually programmed into the DN8000 by the user.
Xb, Xn & Xds - Mono: This program should be used with the Xb, Xn and Xds loudspeaker systems for
mono, short/mid-throw applications with subwoofers. Typical applications would include a ground-stack
combination of front-fill systems and subwoofers as part of a large front-of-house system and small front-
of-house systems. Xcb systems may be substituted for the Xb systems and Xcn systems may be substi-
tuted for the Xn MB and HF sections using these same DN8000 settings. The Xb and Xn LF sections
share the same drive signal (although the Xn LF amplifier channels must be turned down 6 dB). This
program is included as a DN8000 factory preset.
Xb, Xn & Xds – Mono Max Output: This program should be used with Xb, Xn and Xds loudspeaker
systems for mono, short/mid-throw applications with subwoofers where the maximum possible output is
required from the Xn loudspeaker system. Typical applications would include small front-of-house sys-
tems, side-fill and front-fill systems where maximum SPL is required. This program is not included as a
factory preset and must be manually programmed into the DN8000 by the user.
X-Array A: This factory preset may be found on some DN8000 controllers. It was a preliminary configu-
ration for some early X-Array™ prototype loudspeaker systems and should not be used. This configura-
tion is not included in the digital-parameter spreadsheet.
X-Array B: This factory preset may also be found on some DN8000 controllers. It was a preliminary con-
figuration for some early X-Array™ prototype loudspeaker systems and should not be used. This configu-
ration is not included in the digital-parameter spreadsheet.
Xw12: This program should be used with the Xw12 loudspeaker system for floor monitor applications.
Xw12 & Xcb: This program should be used with the Xw12 and Xcb loudspeaker system for drum monitor
applications. The Xb low-frequency system may be substituted for the Xcb system.
Xw15: This program should be used with the Xw15 loudspeaker system for floor monitor applications.