User Manual

9
– PRESETS –
Press and release the PRESET footswitch once to enter PRESET MODE. The Ravish
has ten fully programmable presets. Saving a preset will capture the setting of each
of the five black knobs and all internal settings. Once a preset is saved, the Ravish
will remember its settings after power has been disconnected. Preset ten is denoted
by the Roman numeral “X”. The Ravish also has What You See Is What You Get
(WYSIWYG) mode, denoted by a “W” on the preset display.
Preset Save Procedure
1. Once you have created a sound you want to save or if you want to save an
edited preset, turn the MODE/PRESET knob to display the preset LED
number where you want to save the setting to.
2. Press down and hold the MODE/PRESET knob for 3 seconds. The preset
digit will blink to indicate save completion.
3. After the digit stops blinking, release the MODE/PRESET knob. The PRESET
LED will light up solid.
4. Your preset is now saved.
Preset Load Procedure
There are two options for loading presets:
A. Press and release the PRESET footswitch repeatedly until the preset you
want to load is selected. Make sure the PRESET LED is lit to indicate your
preset is loaded. Please Note: The current knob positions are no longer
valid.
B. Use the MODE/PRESETS knob and the PRESET footswitch.
1. Turn the PRESETS knob so the preset number where the preset was
saved is selected.
2. Press and release the PRESET footswitch. The PRESET LED will light up
to indicate that the preset is loaded. Please Note: The current knob
positions are no longer valid.
After loading a preset, if you move a knob, the knob’s new location will supersede
the preset’s stored value for that knob. At this point, the PRESET LED will blink
rapidly to indicate that a knob has been moved, though a preset is still loaded.
Preset Unload Procedure
A preset can be unloaded to restore the current knob positions. Turn the
MODE/PRESETS knob clockwise until a “W” appears on the preset display. Once the
“W” appears, the preset is unloaded and the current knob positions take over. This
will also revert the KEY, DECAY, MODULATION and PITCH BEND parameters to their
prior, non-preset settings. If preset X is loaded, upon pressing the PRESET
footswitch, the Ravish will cycle to WYSIWYG mode, where no preset is loaded.
Press the PRESET footswitch again and preset 1 will load.
Factory Preset Restore Procedure
1. Press and hold down the MODE/PRESET knob and the PRESET footswitch
while applying power.
2. After applying power, continue to hold down both switches until you see all
of the LEDs blink rapidly. At this point you can release the switches; the
factory presets have been restored.
10
- WARRANTY INFORMATION -
Please complete and return the enclosed warranty card within 10 days of purchase.
Electro-Harmonix will repair or replace, at its discretion, a product that fails to
operate due to defects in materials or workmanship for a period of one year from
date of purchase. This applies only to original purchasers who have bought their
product from an authorized Electro-Harmonix retailer. Repaired or replaced units will
then be warranted for the unexpired portion of the original warranty term. If you
should need to return your unit for service within the warranty period, please include
a brief description of the problem as well as you name, address, telephone number,
copy of your receipt, and a check or money order.
The costs for shipping and handling are listed below.
Electro-Harmonix
c/o New Sensor Corporation
55-01 2nd St.
Long Island City, NY 11101
Attn: Service Department
United States
Canada
Europe and other outside counties
Please make checks/money orders payable to:
New Sensor Corporation
To hear demos on all EH pedals visit us on the web at www.ehx.com.
Email us at [e-mail]
- FCC COMPLIANCE -
Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the user's
authority to operate the equipment under FCC rules.