Troubleshooting guide

ManualsBrandsElectro-Air ManualsAir CleanerEASASD-18ASC

INSTALLATION, OPERATION AND

SERVICE INSTRUCTIONS

MODELS

ASAS-10ASC, ASAS-11ASC, ASAS-12ASC, ASAS-18ASC

GSAS-10ASC, GSAS-11ASC, GSAS-12ASC, GSAS-18ASC

ELECTRONIC AIR CLEANERS

IMPORTANT: PLEASE READ MANUAL BEFORE OPERATING UNIT

Features

•

Lifetime Filter System never needs replacing

• Electronically removes dust, mites, pollen, pet dander, tobacco smoke, cooking smoke

and grease, mold, fungi, bacteria, and more down to 0.01 micron

• Light Weight Aluminum Collecting Cells are durable and easy to maintain

• Cell Guides ensure proper placement of collecting cells

• Activated Carbon Filters remove unpleasant odors

• Galvanized Steel Cabinet for solid vertical or horizontal installation

• Durable Scratch-Resistant powder coat paint finish resists corrosion

• Electronic Air Proving Switch for quick wiring

• Dual Indicator Lights show Air Cleaner is working properly at a glance

FOR QUESTIONS REGARDING INSTALLATION, OPERATION & SERVICE,

CALL THE AIR CLEANER HOTLINE TOLL-FREE

1-800-267-8305

Summary of content (12 pages)

PAGE 1
INSTALLATION, OPERATION AND SERVICE INSTRUCTIONS MODELS ASAS-10ASC, ASAS-11ASC, ASAS-12ASC, ASAS-18ASC GSAS-10ASC, GSAS-11ASC, GSAS-12ASC, GSAS-18ASC ELECTRONIC AIR CLEANERS IMPORTANT: PLEASE READ MANUAL BEFORE OPERATING UNIT Features • Lifetime Filter System never needs replacing • Electronically removes dust, mites, pollen, pet dander, tobacco smoke, cooking smoke • • • • • • • and grease, mold, fungi, bacteria, and more down to 0.
PAGE 2
IMPORTANT: Please read entire instructions before installing the Electronic Air Cleaner. WARNING Before beginning any installation or modification, be certain that the main line electrical disconnect switch is in OFF position. Electric shock could result. Tag disconnect switch with suitable warning labels.
PAGE 3
Table 1 — SPECIFICATIONS MODEL A/ GSAS-10ASC A/ GSAS-11ASC A/ GSAS-12ASC A/ GSAS-18ASC House Size Area <2400 ft² <222.96 m² <3000 ft² <278.70 m² <3000 ft² <278.70 m² >3000 ft² >278.70 m² Airflow up to 1200 cfm up to 2039 m³/hr up to 1400 cfm up to 2379 m³/hr up to 1400 cfm up to 2379 m³/hr up to 2000 cfm up to 3398 m³/hr Duct Size 16 x 20 in 40.5 x 51.0 cm 16 x 25 in 40.5 x 63.5 cm 20 x 20 in 51.0 x 51.0 cm 20 x 25 in 51.0 x 63.5 cm Unit Weight 28.0 lbs 12.9 kg 30.0 lbs 13.5 kg 33.
PAGE 4
Fig. 3 — DIMENSIONS Performance Indicator Light Power Switch AIR FLOW Left to Right or Right to Left Air Proving Switch Î Handle Door DIMENSIONS — in (cm) UNIT A B C D E F G H ASAS-10ASC GSAS-10ASC 21 (53.0) 17 (43.5) 23 1/4 (59.0) 13 1/8 (33.5) 20 3/4 (53.0) 1 1/4 (3.0) 23 3/4 (60.5) 2 3/8 (6.0) ASAS-11ASC GSAS-11ASC 21 (53.0) 17 (43.5) 26 (66.0) 13 5/8 (34.5) 24 (61.0) 1 (2.5) 26 1/2 (67.5) 2 1/8 (5.5) ASAS-12ASC GSAS-12ASC 25 7/8 (66.0) 22 (56.0) 21 1/4 (54.
PAGE 5
Wiring Wiring should only be performed by qualified personnel only. All wiring must comply with all applicable codes and standards. The voltage of the power source must match the voltage indicated on the Air Cleaner. The Air Cleaner should operate ONLY when the system fan is running. Make sure the Air Cleaner is properly grounded. WARNING Electrical shock can cause injury or death. Be certain main line disconnect switch is off before wiring. Wire the Air Cleaner directly to the 120 V power source.
PAGE 6
efficiency. The frequency of cleaning will vary from one house to another. On average, the cells should be cleaned every 3 months. 1. Remove access door, collecting cells and prefilters. 2. Place cells in a laundry tub. Rinse with hot water and spray completely with DAX Detergent (or a non-chlorine, non-corrosive, non-abrasive liquid household detergent. Allow detergent to run down both sides of plates and ionizing wires. Let stand for 5 minutes. 3. Rinse cells well with hot water (maximum 120° F/49°C).
PAGE 7
Replacing An Air Proving Switch (APS) Before replacing the APS, turn off the power to the Air Cleaner at the source. 1. Disconnect wiring from terminals 1, 2, 3, and 4 on the APS. See Fig. 5 and 6. 2. Release circuit board from plastic spacers by pinching end of spacer and pulling board out. 3. Install new APS on plastic spacers. Ensure sensor protrudes slightly through plastic bushing. 4. Connect wiring to terminals on APS. Wiring from power source is connected to terminals 2 and 3.
PAGE 8
Replacing The 24 V Transformer (A/ GSAS-12 and A/ GSAS-18 only) Before replacing 24 V transformer, turn off power to the Air Cleaner at the source. 1. Remove power box cover. 2. Disconnect the secondary leads from the transformer to the 24 V terminals on the power board. See Fig. 6. 3. Cut the primary leads (to the APS) close to the transformer. 4. Remove the 2 hex head nuts from the transformer studs. 5. Remove transformer. 6.
PAGE 9
Testing Voltage At Cell 1. Open access door to Air Cleaner. Air Cleaner will shut off. 2. Insert a thin shafted screwdriver 2 to 3 inches into the hole in the round end plate insulator. See Fig. 9. 3. Attach the ground of the high voltage meter on to a grounded area of the cell. 4. Place the tip of the high voltage probe on the shaft of the screwdriver. Press down the safety interlock. Power to Air Cleaner will come on. 5. Wait until the voltage stabilizes, then take a reading.
PAGE 10
Replacing A Tungsten Ionizing Wire Replacement wires are cut to the correct length and have eyelets at each end for easy replacement. 1. Turn OFF power to Air Cleaner. 2. Remove cell from Air Cleaner. 3. Remove all parts of broken wire, as well as spring and S-hook. If necessary, cell may be used temporarily with one wire missing until a replacement is received. 4. Using needle-nose pliers, place spring hook in the hole of the ionizing bar near cell top. 5.
PAGE 11
Table 3 — TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE REMEDY System fan is not on. Turn system fan on. Wiring improperly connected. Check wiring. Defective power switch. Check power switch for continuity with multimeter. Replace if defective. Defective safety interlock. Remove door and press safety interlock with a screwdriver. If lights come on, bend interlock lever towards front and close door. Power (120 V) is not provided to device. Check power wiring with multimeter.
PAGE 12
ELECTRONIC AIR CLEANER LIMITED FIVE (5) YEAR WARRANTY FIVE YEAR WARRANTY - This GOODMAN product is warranted to be free from electrical and mechanical defects in material and workmanship, under normal use and maintenance within its listed capacity, for a period of FIVE (5) years from the date of purchase. The GOODMAN product must not have been moved from the site of original installation.