USER MANUAL GAS PATIO HEATER EQODHMBR EQODHMGR WARNING: FOR OUTDOOR USE ONLY OR IN WELL VENTILATED AREAS PLEASE KEEP THE MANUAL FOR FUTURE REFERENCE
CONTENTS SAFETY 3 PARTS LIST 5 ASSEMBLY 6 OPERATION 9 LEAK TESTING 10 GAS INFORMATION 10 MAINTENANCE 11 STORAGE 11 TROUBLESHOOTING 12 TECHNICAL SPECIFICATIONS 13 SUPPORT 13 2
IMPORTANT SAFETY INFORMATION Please read this user manual before using this heater and keep it safe for future reference. ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ Read the following instructions carefully and be sure your patio heater is properly installed, assembled and cared for. Retain the instructions for future reference. Failure to follow these instructions may result in serious bodily injury and/or property damage.
For use outdoors or in well ventilated areas. • A well-ventilated area must have a minimum of 25% of the surface area open. • The surface area is the sum of the walls surface. • The use of this appliance in enclosed areas can be dangerous and is PROHIBITED. • Children and adults should be aware of the high operating temperatures of areas above the post when operating this heater. Children should be carefully supervised when in the vicinity of the heater.
PRODUCT OVERVIEW 5 PART DESCRIPTION QUANTITY A Reflector Panel 3 B Reflector Plate 1 C Burner head Assembly 1 D Deck Ring 1 E Wicker table 1 F 1 G Wicker tank housing assembly Post H Wheel kits 1 1
PATIO HEATER ASSEMBLY Required Tools: Philip Screwdriver / Adjustable Spanners / Wrenches Leak Detection Solution: one-part detergent and three parts water Assemble all nuts and bolts loosely at first. Tighten all connections after completion of assembly. This eases your work and increases the stability of your appliance. Before assembly, make sure all packing material and any transmit protection must be moved. Small deviations in equipment may occur. This is no lack of quality but subject to improvements.
4. Attach the reflector panels (A) together using M6 x 8mm screws (FF), Φ6 washers (DD) and cap nuts (GG). Secure loosely with cap nuts (GG). Note: In order to achieve proper alignment of reflector sections, it may be necessary to loosen the preassembled bolts prior to assembly and retighten once complete. 5. Attach the reflector plate (B) to reflector panels (A) using M6 x 8mm screws (FF), Φ6 washers (DD) and cap nuts (GG). Secure loosely with cap nuts (GG).
7. Connect hose & regulator to gas pipe (I). Insert gas pipe with hose & regulator assembly (I/J) through top of the housing (F) and Post (G), tighten gas pipe (I) to head assembly(C). Secure the head assembly (C) to the post (G) using preassembled bolts M5 x 10 (HH), lock washer (JJ), and Φ5 washers (EE). Note: The pressure regulator and hose assembly to be used must conform to local standard codes. 8. Secure gas hose and regulator (J) onto gas cylinder (not included).
OPERATING INSTRUCTIONS BEFORE FIRST USE AND AFTER EVERY GAS CYLINDER CHANGE, GAS DELIVERY SYSTEM MUST BE PURGED OF AIR BEFORE IGNITING! TO DO THIS, TURN THE CONTROL DIAL ANTI-CLOCKWISE TO THE PILOT SETTING. PRESS THE DIAL IN AND HOLD FOR 1 MINUTE BEFORE ATTEMPTING IGNITION. BATTERY REPLACMENT Remove the ignition cap from the BURNER ASSEMBLY (J) by turning cap counterclockwise. Install 1 AAA battery. The negative end of battery goes in first, then replace the ignition cap by turning the cap clockwise.
LEAK TESTING NEVER USE A NAKED FLAME TO CHECK FOR LEAKS. NEVER LEAK TEST WHILE SMOKING. The gas connections on this appliance are leak tested at the factory prior to shipment. This appliance needs to be periodically checked for leaks and an immediate check is required if the smell of gas is detected. • Make a soap solution using 1 part of liquid dish-washing soap to 3 parts water. The soap solution can be applied with a soap bottle, brush, or rag to the leak tested points shown in the figure above.
MAINTENANCE To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis: • • • Keep exterior surfaces clean. Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents. While washing your unit, be sure to keep the area around the burner and pilot assembly dry at all times. If the gas control is exposed to water in any way, DO NOT try to use it. It must be replaced. • Airflow must be unobstructed.
TROUBLESHOOTING PROBLEM Pilot won’t light Pilot won’t stay lit Burner won’t light Burner flame is low Note: Do not operate heater below 5℃(40°F) Emitter glows uneven Note: Bottom 2.
TECHNICAL SPECIFICATIONS Product Name Model Country Code Category Gas Pressure(mbar) 0063 Patio Heater EQODHMBR EQODHMGR BE-CY-CH-CZFR-ES-GB-GRIE-IT-PT-SK-SITR I3+(28-30/37) BG-HR-CH-CY-DKEE-FI-GR-HU-IT-ISLT-LV-MT-NL-NO-PTSE-SI-SK-RO-TR I3B/P(30) CZ-FR-GBGR-IE-PT PL AT-CH-DE AT-CH-DENL I3P(37) I3B/P(37) I3B/P(50) I3P(50) G30 G31 G30/G31 G31 G30/G31 G30/G31 G31 28-30 37 30 37 37 50 50 Heat input 12.5KW 12KW 13.5kW 12.5KW Consumption 909g/h 873g/h 1.70 1.60 982g/h 1.