USER MANUAL CANOPY COOKER HOOD eiQCHDD60 & eiQCHDD90 Thank you for choosing your electriQ cooker hood. This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and usage.
CONTENTS SAFETY 2 INSTALLATION 4 CONTROL PANEL 6 FILTER INFORMATION 7 BULB REPLACEMENT 9 CLEANING AND MAINTENANCE 10 TROUBLESHOOTING 10 SUPPORT 11 PRODUCT FICHE 12 1
SAFETY PRECAUTIONS Whilst this product is compliant with all safety requirements, incorrect or inappropriate use can lead to both personal injury and potential damage to property. Please read the contents of this instruction booklet thoroughly before fitting or using this appliance. • The cooker hood must be installed in accordance with the installation instructions and all measurements followed. • All installation work must be carried out by a competent person or qualified electrician.
• The minimum distance between the surface of the hob and the lowest part of the hood should be at least 65cm. A distance of between 65cm and 75cm gives peak efficiency. • The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels. • When the hood is vented externally and used with appliances which burn fuel (e.g. gas, oil, wood) the area must be sufficiently ventilated to ensure safe operation.
INSTALLATION (VENT OUTSIDE) If you have an outlet to the outside, your cooker hood can be connected as below picture by means of an extraction duct (enamel, aluminum, flexible pipe or nonflammable material with an interior diameter of 150mm) Before installation, turn the unit off and unplug it from the outlet. 1. The cooker hood should be placed at a distance of 15mm from the wall at least. (See Pic1) 2. Put the hood into the hole of the cabinet.
3.Connect the cavity & hood by 8pcs screws (M10*10), the wind direction are up, down, left, right, the user can select according to the space of the cabinet.(See pic 4) Pic 4 4.Fix the pipe on the outlet, and use 4pcs screws (ST4*14) to fix the PCB box, connect the power and finish the installation.(See pic 5) The distance between the edge of cooker hood and the electrical hob or induction hob should be at least 40mm. Refer to pic 6.
CONTROL PANEL Press the timer button to enter the timer settings. To cycle through time settings, use the slide control. The timer can be set to turn off after 5-10-15-20-2530-35-40 minutes. TIMER When the timer has elapsed all functions will turned off and the hood will enter into standby, the decorative cover will close automatically. Press the speed or light button to cancel the timer. LIGHT Press the light button to turn on the light, then use the slide control to change the brightness.
GREASE MESH FILTERS The mesh filters can be cleaned by hand. • Remove the decorative board and wipe it clean with a damp cloth. Then,remove the aluminium filter by pressing and holding the 2 slots. • Place the aluminium filter upside down. Then detach the charcoal filter. • Soak the aluminium filter into the solution of warm water and mild detergent for about 10 minutes. Attaching filters • After cleaning, attach the charcoal filter to the aluminium filter. Then secure with the 3/4 iron wires.
NOTE: • • Make sure the filter is securely locked. Otherwise, it would loosen and cause danger. When activated carbon filter attached, the suction power will be lowered.
BULB REPLACEMENT Note: • Before changing the lights, make sure that the appliance is turned off and unplugged. • Protect against danger when changing lights, such as wearing gloves. Changing the light 1. Remove the decorative board and aluminum mesh, remove the two screws of the fixed lamp board with a screwdriver. 2. Unscrew the 4pcs screws on the LED light strip bracket by cross screwdriver, dismantle the LED light strip and pull out the terminal of the light connecting wire. 3.
MAINTENANCE Before cleaning, switch the unit off and pull out the plug, or switch off at the relevant mains switch if the unit has been hard-wired in. Make sure the unit has no power being fed to it. REGULAR CLEANING Use a soft cloth moistened with warm mildly soapy water or household cleaning detergent. Never use metal pads, chemicals, abrasive material or a stiff brush to clean the unit.
INFORMATION FOR DISMANTLING Do not dismantle the appliance in a way which is not shown in the user manual. The appliance could not be dismantled by user. At the end of life, the appliance should not be disposed of with household waste. Check with your Local Authority or retailer for recycling advice. electriQ UK SUPPORT www.electriQ.co.uk/support Call: 0871 984 4416 Office hours: 9AM - 5PM Monday to Friday www.electriQ.co.
PRODUCT FICHE Symbol Model identification Annual Energy Consumption Time increase factor Fluid Dynamic Efficiency Fluid Dynamic Efficiency class Energy Efficiency Index Value eiQCHDD60 AEChood 40.1 f 0.9 FDEhood 29.
Symbol Model identification Annual Energy Consumption Time increase factor Fluid Dynamic Efficiency AEChood 46.8 f 0.9 FDEhood 31.
