2–4 IMPORTANT INFORMATION Upright Vacuum Cleaner Owner’s Guide 4 GUARANTEE Z2950 Series 5 QUICK REFERENCE 5 HOW TO ASSEMBLE 6 HOW TO USE 7 ROUTINE MAINTENANCE 7 Dust Cup 7 Top Filter 8 Bottom Filter 8 PERIODIC MAINTENANCE 8 Brushroll Household Type IMPORTANT For any advice on your cleaner and to order filters and accessories, please telephone the Electrolux Helpline on 8–9 Brushroll Belt 10 PROBLEM Clear HoseSOLVING 10 Clear Hose 11 Problems and Causes 08706 055055 FILTER
IMPORTANT SAFEGUARDS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER. WARNING To reduce the risk of fire, electric shock, or injury: • Do not use outdoors or on wet surfaces. • Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and before servicing. • Do not allow to be used as a toy.
BEFORE YOU START CHECK THE VOLTAGE Before connecting the cleaner to an electrical supply, ensure that the voltage shown on the rating plate located beneath the cleaner is of the correct voltage for your electricity supply. If it is not, do not use the cleaner but refer back to your dealer. CONNECTING TO YOUR ELECTRICITY SUPPLY Permanently connected to the cleaner is a mains supply (2-core) cable fitted with a non-rewirable plug incorporating a 13A fuse.
SERVICE Should you require service on your Electrolux cleaner, please telephone Electrolux Customer Services on 08706 055055. Before requesting service, please check whether your problem is covered under Service Checklist (see below). New filter pads, brushrolls and drive belts can be obtained from Electrolux Retailers. If difficulty is experienced in obtaining spares, please contact Electrolux on 08706 055055.
G (some models only) ● H (some models only) ● PARTS LIST (FIG. 1) A Wand and crevice wand (pull apart) ● B Dusting brush ● C Hose ● D Vacuum cleaner body ● E Electrical cord ● F Handle ● G Self-cleaning duster (some models only) ● H Turbo tool (some models only) ● ●I Screws located in the accessory package J Carry handle assembly ● HOW TO ASSEMBLE D ● A ● CAUTION: Assemble the cleaner before using. C ● E ● B ● J ● F ● FIG. 1 FIG. 2 FIG. 3 FIG. 4 FIG. 5 CAUTION: Moving parts.
HOW TO USE FIG. 7 FIG. 8 FIG. 9 6 FIG. 10 20 WARNING: Avoid injury. Keep loose clothing, hair, fingers, and all other parts of body away from any moving part (such as the revolving brush). Turn off the switch and unplug the cleaner before changing the cleaner height setting. ON/OFF Switch. International symbol I means On, International symbol O means Off (FIG. 7). Handle Release (FIG. 8). Step on handle release to pull handle back to a comfortable operating position.
ROUTINE MAINTENANCE Note: Turn off the switch and unplug the electrical cord before routine maintenance. Never operate the vacuum cleaner without the top and bottom filters in place. Note: When vacuuming carpet fresheners or cleaners, powder, plaster dust, or similar fine substances, the top and bottom filters will require more frequent maintenance. Removing the Dust Cup Step 1: Remove dust cup by sliding dust cup lever from right to left (FIG. 11). Step 2: Grasp dust cup with both hands and pull out (FIG.
ROUTINE MAINTENANCE (continued) Filter Screen The filter screen is located directly above the dust cup and is easily removed by turning it counter-clockwise. It should be checked regularly to ensure an open airway. Reinsert the screen by turning it clockwise (FIG. 17). Bottom Filter Maintenance (Ref. EF82) FIG. 17 Check the bottom filter frequently. For optimum performance, replace bottom filter every 12 months.
PERIODIC MAINTENANCE (continued) How To Replace Brushroll Belt FIG. 21 Step 1: Lower handle to floor to change belt (FIG. 21). Step 2: Remove the two screws from the top of the hood (FIG. 22). Step 3: Lift hood to remove (FIG. 23). Step 4: Lift right end of brushroll (FIG. 24). Step 5: Remove and discard belt. Step 6: Place new belt around motor shaft. Step 7: Place new belt around brushroll pulley. Step 8: Align left end cap with base. Push end cap securely into place.
PROBLEM SOLVING How to Clear Blockages in Hose Hose Retainer Hose FIG. 26 Edge Kleen™ model shown (some models only) FIG. 27 10 FIG. 28 20 CAUTION: Turn off the switch and unplug the electrical cord before periodic maintenance. Step 1: Firmly pull the end of the hose from the hose retainer on the hood of the vacuum (FIG. 26). Step 2: Check for blockages in the hose and hose retainer. Flexing the hose may help loosen any blockage. If no blockage is found, continue to step 4.
PROBLEM SOLVING CAUTION: Turn off the switch and unplug the electrical cord before servicing. Problem Cause Solution Motor will not start Electric Plug • Push plug securely into outlet • Try another outlet • Check circuit breaker Motor stops suddenly Thermal Cut Off • Refer to page 2 Does not clean the carpet or floor Filters • Clean or replace filters.
If you experience any problems with your cleaner, don’t struggle taking it back to the shop. Call our dedicated Customer Helpline for help and advice on 08706 055055 Accessory Items in This Carton 1 Dusting/Upholstery Brush 1 extra belt Dust Cup Filter (DCF16) Riser Visor Turbo (on some models) 1 extension tube, 1 crevice wand 1 accessory package (2 screws) 1 vacuum cleaner handle Thank you for purchasing an Electrolux cleaner.
