User Manual Software Version 1.
Power Spot 575IE™ ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
Power Spot 575IE™ Table of Contents Introduction..........................................................................................................................5 Unpacking ......................................................................................................................5 Customer Support .......................................................................................................5 Discharge Lamp Precautions ............................................................
Power Spot 575IE™ 3.9.6 Fixture Temperature (TEMP)....................................................................... 22 3.9.7 Fan Control (FANS) .................................................................................... 22 3.9.8 Adjustments and Calibrations (ADJU) ...................................................... 23 3.9.9 Default Settings (DFSE).............................................................................. 24 3.9.10Feedback (FEED) ........................................
Power Spot 575IE™ INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable lighting fixtures on the market today! The Power Spot 575IE™, has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance.
Power Spot 575IE™ If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Items returned without a R.A. number clearly marked on the outside of the package will be refused and returned at cutomers exspence. You may obtain a R.A. number by contacting customer support at (323) 582-3322. DISC HARGE LAMP WARNING: This fixture is fitted with a discharge lamp, which is highly susceptible to damage if improperly handled.
Power Spot 575IE™ Safety Instructions The Power Spot 575IE™ is an extremely sophisticated piece of electronic equipment. To guarantee a smooth operation, it is important to follow the guidelines in this manual. The manufacturer of this device will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. Always be sure that the fan and the air inlets remain clean and are never blocked.
Power Spot 575IE™ 1. Fixture Layout 1 1. Lens Assembly 2. DMX Input Jack 8 3. DMX Output Jack 4. Microphone Sensitivity Adjustment Knob 5. Firmware Connection 6. Internal Cooling Fan 7. Base 8. Retaining Arm 7 2 4 3 6 5 9 10 15 16 17 18 11 9. Lamp Fuse Holder 10. Electronics Fuse Holder 11. Powercon Connector 12. Power Switch 13. Carrying Handle 14. 4-Segment Menu Display 15. Mode Select Button 6 13 14 12 16. Enter Select Button 17. Down Select Button 18.
Power Spot 575IE™ 1. Lens Assembly - This high quality lens is a fully focusing. Focus the lens b y manually turning the lens in a clockwise or counter-clockwise direction until the desired effect is achieved. 2. DMX Input Jack – This 3-Pin XLR jack is used to receive an incoming DMX signal. 3. DMX Output Jack – This 3-Pin XLR jack is used to send an outgoing DMX signal. For best results this jack should be terminated if it is the last fixture in a DMX daisychain (see termination on page 14). 4.
Power Spot 575IE™ 12. Power Switch – The switch is used to control main power to fixture’s electronics. 13. Carrying Handle – The fixtures includes two built-in carrying handles. Be sure to always handle the fixture by the built-in carrying handles. Never lift or carry the fixture by the head or retaining arms as this could cause serious damage to the fixture and void your manufactures warranty. 14. 4-Segment Menu Display – This display details menu functions. 15.
Power Spot 575IE™ 2. Preparation and Installation 2.1 Mounting The POWER SPOT 575IE™ is fully operational in two different mounting positions, hanging upside from a ceiling or set on a flat level surface. To avoid internal damage to the unit, never mount the unit on its side as illustrated below. Be sure this fixture is kept at least 0.5m away from any flammable materials (decoration etc.). Install a safety cable that can hold at least 10 times the weight of the fixture.
Power Spot 575IE™ attached to the cam lock, attach the cam locks to the designated position on the bottom of your unit. Lock the cam locks into position by turning the wing nuts 90°. 90° b) Be sure to always use two cam locks mounted to the bottom of unit to ensure safe truss mounting (each two opposite threads max. M10x20). 4x M10x20mm 4x Camlock 2.
Power Spot 575IE™ 2.3 Connections 2.3.1 Power supply Electronic ballast with: 90~260 Volts, 50~60 Hz, Grounded contact type plug – Neutrik Powercon Connected load 780W <=> 3.8A (blind current compensation). NOTE: The universal power supply will accept any voltage source as detailed above without any type of internal or user modifications. 2.3.2 DMX-512 3-Pin XLR Input/Output. [+] = Pin 3 / [-] = Pin 2 / [Ground] = Pin 1 DMX-512: DMX is short for Digital Multiplex.
Power Spot 575IE™ conductor shielded cable (This cable may be purchased at almost all professional sound and lighting stores). Your cables should be made with a male and female XLR connector on either end of the cable. Also remember that DMX cab le must b e daisy chained and can not b e sp lit. 2.5 Notice: Be sure to follow the above figure when making your own cables. Do not use the ground lug on the XLR connector.
Power Spot 575IE™ 2.8 Fuse Requirements The POWER SPOT 575IE electronic and lamp systems are protected by two G M A (5x20mm) external fuses: Lamp: 250V/8A Electronics: 250V/1A The fuse requirements are clearly printed on the side of the fixture. WARNING: • Always disconnect main power before changing the fuse! • Always replace with the exact same type fuse unless otherwise specified by an authorized Elation® service technician.
Power Spot 575IE™ Fixture Menu DOWN - UP LAMP RESE TIME RPAN RTLT SPEC Level 2 Level 3 ASLW AFST MSTR SVPT SIZE POWR LA1 LA2 MANU LAAU DLOF DMXI DISP TEMP FANS ADJU D ON REV HIGH REG LOOF LOHI CODE xxxx COLO GOB1 GOB2 SHTR PRIS IRIS POFS TOFS clre ares VTIL MODE ENTER DOWN Display MODE Level 1 D001 TEST AUDI MODE ENTER DOWN UP DOWN ENTER The control panel located on the side of the fixture allows you to access the main menu and make all necessary adjustments to the P O W E R SPOT 575IE™.
Power Spot 575IE™ VTR1 VTR2 VTR3 DFSE FEED EFLG Software version, driver board 1 Software version, driver board 2 Software version, driver board 3 Call on the default function values Pan/Tilt feedback (error correction) On/Off Correction of faults 3.1 Setting/Changing the DMX Address After applying power to the POWER SPOT 575IE™ the LED will display the fixture’s current DMX address immediately after the reset sequence. If the fixture is not receiving a DMX signal the display will flash continuously.
Power Spot 575IE™ 3.3 The Audio Program Audi The Audio menu allows you to run a stand-alone audio program. This program can run either fast (AFST ) or slow (Aslw ); Fast (AFST ): When running in “fast” mode every sound impulse will trigger a new step. (Aslw ): When running in You may run several fixtures together at once to achieve a synchronized light show running to sound in a Master/Slave configuration. To run in a Master/Slave. Additionally you can choose a basic position for this audio chaser.
Power Spot 575IE™ This function will rest and return all motors to the home position. Access the reset function in the main menu and press the Enter button to engage the reset function (RST will readout in the display). 3.6 Running Time (lamp/unit) TIME This menu function will read out three different fixture running times. POWR Fixture running time (non destructible). Total running time logged by the unit. LA 1 Lamp running time (erasable).
Power Spot 575IE™ special functions and their sub-menus are as followed: 3.9.1 Manual Drive MANU This feature allows you to drive all the unit’s functions manually for use in an environment that requires a static position (no movements), determining focus points, or testing. Use the Up and Down buttons to select the function you wish to adjust, then use the Enter button to accept your selection. Now adjust the values with the Up and Down buttons and use the Enter button to lock in your value.
Power Spot 575IE™ Please note: ON is the default setting for this function. 3.9.3 Lamp Off via DMX DLOF This function allows the lamp to be switched off through a DMX controller. To enable this function use the Up and Down buttons to toggle between ON and Off. Turn this function “ON” to allow DMX switching. Use the Enter button to accept your selection or the Mode button to cancel and return to the menu. 3.9.
Power Spot 575IE™ 3.9.5 Display DISP Use this function to choose between different display indications. Use the Up/Down-keys to select desired function and press Enter to confirm or Mode to cancel and return to the menu. D ON REV Display On/Off (If you've chosen off, the display will go out within 15 seconds after the last input. The next key touch will reactivate the display). Rotates the display by a 180˚ - This may also be accomplished b y pressing both the “UP” and “DOWN” buttons at the same time.
Power Spot 575IE™ REG LOOF LOHI constantly monitors the internal operating temperature and regulates the fan speed to coincide with the internal temperature. This function is designed for environments that require low ambient noise. In this setting the fan will operate at the lowest speed. When the maximum internal intolerable operating temperature is reached the lamp will automatically shut off. In this setting the fan will operate at the lowest speed.
Power Spot 575IE™ VTR1 VTR2 -99 - +99 -99 - +99 Software version of Head- board Software version of Base- board 3.9.9 Default Settings DFSE This function is used to restore all the factory default settings and presets. Press the Enter button to confirm this operation or the Mode button to cancel and return to the menu. When this operation is selected the LED will briefly readout ok , then return to the previous function. The chart below details the factory defaults.
Power Spot 575IE™ 3.10 Display Error and Information Messages This message appears if you try to switch on the lamp within 5 minutes after having switched off (lamp too hot). The message will appear on the display if the lamp doesn’t ignite within 20 seconds. The fixture will store this command and automatically ignite the lamp after 5 minutes. IG E When igniting the lamp, the electronic ballast will examine whether the lamp ignited or not.
Power Spot 575IE™ 4. Operation Operating Modes: The Power Spot 575IE™ can operate in three different modes. This next section will detail the differences in the operating modes. • Stand alone mode - The fixture will react to sound, chasing through the built-in programs. • Master/Slave mode - You can daisy chain up to 16 fixtures together to get a synchronized light show without the need of an external controller. The fixtures will react to sound chasing to synchronized light show.
Power Spot 575IE™ switched “OFF.“ 4.2.5 Choose your room size. The size function allows you to choose a the approximate size of the room (NORM, BIG, MIDL, SMAL). The built-in programs will automatically adjust to your slection to optimize light output for your room. 4.2.6 Use the sound sensitivity knob on the side control panel to make the unit more or less sensative to sound.
Power Spot 575IE™ 5. DMX CHANNEL SELECTION (DMX PROTOCOL) Power Spot 575IE DMX Channel Selection Channel Function 1) PANcoarse 2) PANfine 3) Tiltcoarse 4) Tilt-fine 5) Color 0 .. 530° Time and Value min. 2,65 s High- Pos ... High- Pos + 2,1° (16 Bit) 0 .. 285° min. 1,8 s High- Pos … High- Pos + 1,1° (16 Bit) open (fast) open / color 1 (fast) color 1, Brilliant Blue (fast) color 1 / color 2 (fast) color 2, Blue (fast) color 2 / color 3 (fast) Chaser from color to color max.
Power Spot 575IE™ Channel Function Time and Value DMX HEX % color 2, Blue (slow) color 2 / color 3 (slow) 72..73 74..75 28,4 29,2 color 3, Blue Purple (slow) 76..77 color 3 / color 4 (slow) color 4, Magenta (slow) color 4 / color 5 (slow) color 5, Pink (slow) color 5 / color 6 (slow) color 6, Orange (slow) color 6 / color 7 (slow) 78..79 80..81 82..83 84..85 86..87 88..89 90..91 color 7, Canary (slow) 92..93 254 48..49 4A..4 B 4C..4 D 4E..4F 50..51 52..53 54..55 56..57 58..59 5A..5 B 5C..
Power Spot 575IE™ Channel Function Time and Value => 1,51 s Gobo 2 (slow) 80..87 Gobo 4 (slow) 88..95 Gobo 5 (slow) 96..103 Gobo 6 (slow) 104..111 Gobo 7 (slow) 112..119 Gobo 8 (slow) Gobo rotation STOP Gobo rotation, slow-fast, CW Gobo rotation, fast-slow, CCW 120..127 128..129 130..191 192..253 min. 1,4 turns/h max. 1.0 turns/sec. each 4th sound impulse new gobo each sound impulse new gobo Audio gobo chase, fast Posi./Rot Gobo position 0 ...
Power Spot 575IE™ Channel Function Time and Value Gobo 6 (slow) Gobo 7 (slow) 84..87 88..91 Gobo 8 (slow) Gobo 9 (slow) 92..95 96..99 Gobo 10 (slow) Gobo rotation STOP Gobo rotation, slow-fast, CW Gobo rotation, fast-slow, CCW min. 1,4 turns/h max. 1.0 turns/sec. Audio gobo chase, fast Audio gobo rotation, fast Shutter closed Random Strobe (different pattern) Strobe Pulse effect , slow - fast 254 Audio prism rotation, fast 54..57 33..34 58..5B 35..35, 9 5C..5F 36..37 60..63 38..38, 9 64..7F 39..
Power Spot 575IE™ Channel Function Time and Value Ascend - descend effect Iris open 14) Special No function Gobo-shake +/- 10° slow – fast Gobo-shake +/- 20° slow – fast Gobo-shake +/- 30° slow – fast Color-chaser C / C+1 slow – fast Color-chaser C / C+2 slow – fast Audio Pan / Tilt slow 3,5 moves / min. up to 60 moves / max. 3,5 moves / min. up to 60 moves / max. 3,5 moves / min. up to 60 moves / max. 0,7 BPS ... 2,3 BPS => 1,43 s ... 0,43 s 0,7 BPS ... 2,0 BPS => 1,43 s ...
Power Spot 575IE™ Channel Function PAN Time and Value DMX 4 4 0° 90° 24..25 26..27 4 180° 28..29 4 TILT PAN / TILT PAN / TILT (inverse) Circle Circle (inverse) 270° size / phase see also PAN size / phase see also PAN size / phase see also PAN size / phase see also PAN size / phase see also PAN 30..31 32..63 64..95 96..127 128..159 160..191 lying eight size / phase see also PAN 192..223 HEX % 18..19 9,6 1A..1 10,4 B 1C..1 11,2 D 1E..1F 12 20..3F 13..25 40..5F 26..37 60..7F 38..50 80..9F 51.
Power Spot 575IE™ 6. Lamp Replacement For a proper and safe lamp change, please read this chapter carefully and follow all instructions. 6.1 Safety Regulations 6.2 • Pull out the main plug! • Wait min. 20 minutes after the last operation to cool down the fixture. • Don’t touch the bulb of the lamp with bare fingers (this can cause damages. • Before you put the POWER SPOT 575IE™ into operation close the casing, otherwise your retina can be hurt! Lamp Change 6.2.
Power Spot 575IE™ components. 6.2.5 Replace the lamp with an approved replacement type. Be sure to follow all the lamp handleing procedures included with your new lamp. Never handle the new lamp with your bare hands, the oils from your skin may damage the lamp. Always replace with the lamp with a lamp that meets the orginal lamp specification, failure to do so may damage the unit and will void your manufactures warranty. 6.2.
Power Spot 575IE™ 7. Fuse Replacement Caution: Always replace with the exact same type fuse, unless otherwise specified by an authorized Elation® service technician. Replacing with anything other than the specified part can damage your unit and will void your manufactures warranty. Warning: If you continue to blow fuses, STOP using the fixture. Contact customer support for further instructions, you may have to return the unit for servicing. Continuing to use the unit may cause serious damage.
Power Spot 575IE™ 8. Changing/Replacing Gobos The POWER SPOT 575IE™ is fitted with a standard size gobo wheel that accepts gobos with an outside diameter of 27mm and a viewable image size of 23mm. Glass or steel gobos may be used. Please follow the safety procedures and installation below for proper and pain gobo exchange.
Power Spot 575IE™ If you use glass gobos, the non-vaporized side must be fitted towards the lamp direction. Magnet Open Wheel with rotating Gobos ©Elation Professionals® Los Angeles, Ca. Wheel with non rotating Gobos - wwww.ElationLighting.
Power Spot 575IE™ 9. Maintenance and Cleaning the POWER SPOT 575IE™ It is absolutely essential that the fixture is kept clean and dust, dirt and smoke-fluid residues do not built-up on the surface or within the fixture. Otherwise the fixture's light output could b e significantly reduced. Regular cleaning will not only ensure the maximum light output, but will also allow the fixture to function reliable throughout its life.
Power Spot 575IE™ Attention: 1. Never allow optical parts to come in contact with oil, dirt, or grime. 2. Allow all parts to dry completely before attempt operation. 3. Never clean the aspheric lens with water or other cleaners. The lens should be changed at the first sign of ware, usually in about 1 – 2 years (lens will begin to look cloudy). For lens replacement please contact Elation technical support. 9.3 Cleaning the Optical System technicians only) (recommended for qualified service 9.3.
Power Spot 575IE™ 10. Technical Specification Power supply Power consumption Fuse protection 90~260V, 50~60 Hz 780 Watt, 3.8A, electronic ballast, (blind current compensated) Lamp: 8A/250V, GMA (5x20mm fine-wire fuse) Electronic: 1A/250V, GMA (5x20mm fine-wire fuse) Lamp Type HTI 575-DE (OSRAM) Live time 500h (750h) Color temperature 5600k or 7500k luminous flux 43.
Power Spot 575IE™ 2 YEAR (730 DAYS) LIMITED WARRANTY A. Elation Professionals® hereby warrants, to the original purchaser, Elation Professionals® products to be free of manufacturing defects in material and workmanship for a period of two years (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
Power Spot 575IE™ F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited b y applicable law, all implied warranties made by Elation Professionals® in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above.
Power Spot 575IE™ 11. Dimensions ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
Power Spot 575IE™ ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
Power Spot 575IE™ Laser Warning Labels: When installing this fixture be sure that it is mounted in a manner that prevents the audience from directly into the laser beam. Be sure the fixture is mounted in manner that prevents the laser beam from sticking the audience. ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
Power Spot 575IE™ 12. Index A I Adjustments..................................................23 aspheric lens.....................................................40 Injury of the retina ............................................... 7 B BGV C1 ............................................................11 Blind current compensation ...............................13 Maintenance .................................................... 39 Measures .........................................................
Power Spot 575IE™ Elation Professional 4295 Charter Street Los Angeles, CA. 90058 323-582-3322 / 323-582-3108 fax www.ElationLighting.com / info@ElationLighitng.com ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
