Design LED 60 TriStrip Elation Professional™ 6122 S. Eastern Ave. Los Angeles, CA. 90040 www.elationlighting.com Rev.
Design LED 60 TriStrip™ ©Elation Professional, Los Angeles Ca. 1 www.ElationLighting.
Design LED 60 TriStrip™ TABLE OF CONTENS 1. General Information……………………………………………………………………… 3 a. Introduction………………………………………………………………………. 3 b. Unpacking………………………………………………………..…………..… 3 c. Customer Support…………………………………………….………………… 3 d. Warranty Registration……………………………………………………..…… 3 2. Safety Instructions………………………………………………………........…………. 5 3. Features……………………………………………………………………………………7 4. General Guidelines………………………………………………………………………. 8 5. Fixture Overview…………………………………………………………………………. 9 6.
Design LED 60 TriStrip™ 1. GENERAL INFORMATION INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable LED fixtures on the market today! The Design LED 60 TriStrip™ has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit.
Design LED 60 TriStrip™ rain or moisture. Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself. Doing so will void your manufactures warranty. Please do not discard the shipping carton in the trash. Please recycle whenever possible. WARRANTY REGISTRATION: The Design LED 60 TriStrip™ comes with a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase.
Design LED 60 TriStrip™ 2. SAFETY INSTRUCTIONS To guarantee proper and consistent operation, it is important to follow the guidelines in this manual. Elation Professional will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. Always be sure that the fan and the air inlets remain clean and are never blocked. Allow about 6” (15cm) between this fixture and other devices or a wall to allow for proper cooling. 2.
Design LED 60 TriStrip™ sure the power cord is never crimped or damaged. If the power cord is damaged, replace it immediately with a new one of similar power rating. 13. Always disconnect from main power before performing any type of service or any cleaning procedure. 14. Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion of the cord. 15. Please be aware that damages caused by modifications to the device are not subject to warranty.
Design LED 60 TriStrip™ 3.
Design LED 60 TriStrip™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, and other types of architectural installations. Do not attempt operation or installation without a proper knowledge on how to do so. This fixture was designed for indoor use only; use of this fixture outside will void the manufacture’s warranty. Consistent operational breaks will ensure that the fixture will function properly for many years to come.
Design LED 60 TriStrip™ 5. FIXTURE OVERVIEW 1. Bracket Locking Knob – This knob is used to secure the bracket in place after angle adjustments have been made. 2. Fixture Chassis – Extruded aluminum slotted chassis, allows similar units to be mounted together. See assembly instructions on page 3. Diffusing Lens/LED Assembly – This lens is used to both protect the LEDs as well as diffuse the light output. Tri-Color LED assembly 4. Eye Bolt – This bolt is used a securing point for a safety cable. 5.
Design LED 60 TriStrip™ 7. Power Output Jack – Use this jack to jump power to another Design LED 60 TriStrip™ 8. 3-Pin DMX Output Jack – This jack is used to send an incoming DMX signal to the next fixture in the DMX chain via a female, 3-pin XLR jack. 9. 3-PIN DMX Input Jack – This jack accepts an incoming DMX signal via a male, 3-pin XLR jack. 10. LED Menu Display - 4-segment menu display. Used to display the DMX address as well as all other menu functions. 11.
Design LED 60 TriStrip™ 6. MOUNTING AND INSTALLATION Yoke Assembly – Single Unit Operation (DLED 12 Brick shown for illustration purposes only). The device can be placed directly on the stage floor or rigged in any orientation on a truss without altering its operation characteristics. When connecting the hanging yoke to the fixture, refer to the illustration below.
Design LED 60 TriStrip™ working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury. Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet.
Design LED 60 TriStrip™ CAUTION! Be sure a qualified electrician performs all electrical connections before attempting any operation. Clamp Mounting The Design LED 60 TriStrip™ provides a unique mounting bracket assembly that allows the unit to stand on flat surface, hang on truss via a clamp, or be used in cluster allow multiple units to rigged together (see the illustration below).
Design LED 60 TriStrip™ 7. UNDERSTANDING DMX DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. DMX allows all makes and models of different manufactures to be linked together and operate from a single controller. This is possible as long as all the fixtures and the controller are DMX compliant.
Design LED 60 TriStrip™ at 120 ohms, this cable is designed for DMX transmission and may be purchased from your Elation dealer or at most professional lighting retailers. Your cables should be made with a male and female XLR connector on either end of the cable. Also, remember that a DMX line must be daisy chained and cannot be split, unless using an approved DMX splitter Be sure to follow the above figure when making your own cables. Do not use the ground lug on the XLR connector.
Design LED 60 TriStrip™ DMX-512 connection with DMX terminator A DMX terminator should be used in all DMX lines especially in longer runs. The use of a terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line.
Design LED 60 TriStrip™ to the digital control information sent out from the DMX controller. The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the head of the fixture. You can set the same starting address for all fixtures or a group of fixtures, or set different address for each individual fixture.
Design LED 60 TriStrip™ 8. DISPLAY MENU MODE ( ) MANU ( ) ADDR ( ) DISP( ) FLIP( ) CHAN ( ) SLAV( CNTL( ) ) A001( ) (1-512) ON/OFF( ) ON/OFF( 3 CH( 4 CH( 6 CH( 15 CH( 60 CH( 63 CH( ON/OFF( MAST( ) ) ) ) ALON( BLAC( COLR( CHAS ( ) CHS1( CHS2( CHS3( CHS4( ) ) ) ) ) ) RED( ) GREN( ) BLUE( ) STRB( ) SPED( ) FADE( ) STRB( ) SPED( ) FADE( ) STRB( ) SPED( ) FADE( ) STRB( ) SPED( ) ©Elation Professional, Los Angeles Ca.
Design LED 60 TriStrip™ CHS5( ) CHS6( ) CHS7( ) CHS8( SOND ( ) OTHR ( ) ) CTRL( MIC( DIMR( ) ) ) LODA( VER( ) ) FADE( ) STRB( ) SPED( ) FADE( ) STRB( ) SPED( ) FADE( ) STRB( ) SPED( ) FADE( ) STRB( ) SPED( ) FADE( ) STRB( ) MAST( ALON( ) ) M-XX( MOD1( ) MOD2( ) 0-255 Adjust program 4 fade time 0-255 Adjust strobe rate of program 4 0-255 Adjust program 5 speed 0-255 Adjust program 5 fade time 0-255 Adjust strobe rate of program 5 0-255 Adjust program
Design LED 60 TriStrip™ 9. DMX OPERATION This fixture can run in five different DMX modes, the following pages will detail the differences in the operating modes as well as how to achieve the different operating modes. DMX Settings: The chart below describes how to access the different DMX modes. The chart below also defines the how a channel will function in the different DMX modes.
Design LED 60 TriStrip™ program. 0-----10 No function 11----40 Program 1 41----70 Program 2 71----100 Program 3 101--130 Program 4 131--160 Program 5 161--190 Program 6 191--220 Program 7 221--255 Program 8 Strobe Function: In 63-channels mode the strobe function is accessed via channels 62. In 15-channels mode the strobe function is accessed via channels 14. In 6-channels mode the strobe function is accessed via channels 5.
Design LED 60 TriStrip™ 10. DMX CHANNEL TRAITS DMX Operation Notes: The fixture will function in DMX mode whenever the unit is receiving a DMX signal. Please note that this will override all manual settings. This unit will keep and retain the last DMX command in the event of DMX signal failure. To reset the fixture you must turn the power off.
Design LED 60 TriStrip™ DMX channel’s functions and their values (3-Channel Mode): Channel 1 - Red: 0-255 Red (0-Black, 255 - 100% Red) Channel 2 - Green: 0-255 Green (0-Black, 255 - 100% Green) Channel 3 - Blue: 0-255 Blue (0-Black, 255 - 100% Blue) ©Elation Professional, Los Angeles Ca. 23 www.ElationLighting.
Design LED 60 TriStrip™ 4 Channel Mode: This chart details a simple layout of the DMX channel assignment in 4-channel mode. CHANNEL 1: Red CHANNEL 2: Green CHANNEL 3: Blue CHANNEL 4: Dimming and speed DMX channel’s functions and their values (4 Channel Mode): Channel 1 - Red: 0-255 Red (0-Black, 255-100% Red) Channel 2 - Green: 0-255 Green (0-Black, 255- 100% Green) ©Elation Professional, Los Angeles Ca. 24 www.ElationLighting.
Design LED 60 TriStrip™ Channel 3 - Blue: 0-255 Blue (0-Black, 255- 100% Blue) Channel 4 - General dimming / Program Speed Control This channel has two functions depending on the operating mode. When running the built-in programs this channel will control the program speed. 0-255 Dimming (0%-100%) ~ Normal Operation 0-255 Speed (min to max) ~ When running built-in programs on channel 4 ©Elation Professional, Los Angeles Ca. 25 www.ElationLighting.
Design LED 60 TriStrip™ 6-Channel mode: In this mode channels 1~3 are used to control the RGB LEDs and channels 4~6 will control special features. 6-Channel Mode: The charts below and on the next page detail the DMX channel layout for 6-channel assignment.
Design LED 60 TriStrip™ 161-190 Internal program 6 191-220 Internal program 7 221-255 Internal program 8 Channel 5 - Strobe: 0 No function 1~95 Strobe effect slow to fast 96-127 No function 128-159 Pulse effect in sequences 160-191 No function 192-223 Random strobe effect slow to fast 224-255 No function Channel 6 - General dimming / Program Speed Control This channel has two functions depending on the operating mode.
Design LED 60 TriStrip™ 15-Channel mode: In this mode channels 1~12 are used to control the various RGB LEDs and channels 13~15 will control special features. CHANNEL 1: Red CHANNEL 2: Green CHANNEL 3: Blue CHANNEL 4: Red CHANNEL 5: Green CHANNEL 6: Blue CHANNEL 7: Red CHANNEL 8: Green CHANNEL 9: Blue CHANNEL10: Red CHANNEL 11: Green CHANNEL 12: Blue CHANNEL 13: Auto Programs (Built-in Programs) CHANNEL 14: Strobe CHANNEL 15: Dimmer/Speed ©Elation Professional, Los Angeles Ca. 28 www.ElationLighting.
Design LED 60 TriStrip™ DMX channel’s functions and their values (15 Channel Mode): Channel 1 - Red: 0-255 Red (0-Black, 255-100% Red) Channel 2 - Green: 0-255 Green (0-Black, 255- 100% Green) Channel 3 - Blue: 0-255 Blue (0-Black, 255- 100% Blue) Channel 4 - Red: 0-255 Red (0-Black, 255-100% Red) Channel 5 - Green: 0-255 Green (0-Black, 255- 100% Green) Channel 6 - Blue: 0-255 Blue (0-Black, 255- 100% Blue) Channel 7 - Red: 0-255 Red (0-Black, 255-100% Red) Channel 8 - Green: 0-255 Green (
Design LED 60 TriStrip™ Channel 10 - Red: 0-255 Red (0-Black, 255-100% Red) Channel 11 - Green: 0-255 Green (0-Black, 255- 100% Green) Channel 12 - Blue: 0-255 Blue (0-Black, 255- 100% Blue) Channel 13 - Internal programs: 0-10 No function 11-40 Internal program 1 41-70 Internal program 2 71-100 Internal program 3 101-130 Internal program 4 131-160 Internal program 5 161-190 Internal program 6 191-220 Internal program 7 221-255 Internal program 8 Channel 14 - Strobe: 0 No function
Design LED 60 TriStrip™ Channel 15 - General dimming / Program Speed Control This channel has two functions depending on the operating mode. When running the built-in programs this channel will control the program speed, when not running the built-in programs this channel will control master dimming. 0-255 Dimming (0%-100%) ~ Normal Operation 0-255 Speed (min to max) ~ When running built-in programs on channel 4 ©Elation Professional, Los Angeles Ca. 31 www.ElationLighting.
Design LED 60 TriStrip™ 60-Channel Mode will function similarly to 3-Channel mode. Where 3-Chanel mode controls all like colors at one time 60-channnle mode will allow you to control each individual color in each pixel. 63-Channel Mode will function similarly to 15-Channel mode. Where 15-Chanel mode controls all like colors in blocks of 5 at a time 63-channnle mode will allow you to control each individual color in each pixel. ©Elation Professional, Los Angeles Ca. 32 www.ElationLighting.
Design LED 60 TriStrip™ 11. CLEANING AND MAINTENANCE The consider the following point during normal service and inspection: 1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall. 2. Electric power supply cables must not show any damage, material fatigue or sediments. Never remove the ground prong from the power cable.
Design LED 60 TriStrip™ 12. 2-YEAR LIMITED WARRANTY A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to be free of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
Design LED 60 TriStrip™ effect. E. Elation Professional® reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above.
Design LED 60 TriStrip™ 13. PHOTOMETRIC DATA ©Elation Professional, Los Angeles Ca. 36 www.ElationLighting.
Design LED 60 TriStrip™ 14. DIMENSIONAL DRAWINGS ©Elation Professional, Los Angeles Ca. 37 www.ElationLighting.
Design LED 60 TriStrip™ 15. LENS CHANGE The Design LED 60 TriStrip comes with a removable front cover that allows the lenses to be swapped to achieve different beam angles. The lens cover is held in place by ¼ turn locking fasteners. To remove the cover; 1) Turn the locking fasteners in a counter-clockwise direction. 2) Once the fasteners are loose lift the cover to expose the lens assembly (see illustration below). 3) Remove or replace the filters and reassemble. ©Elation Professional, Los Angeles Ca.
Design LED 60 TriStrip™ 16. CIRCUIT SCHEMATIC ©Elation Professional, Los Angeles Ca. 39 www.ElationLighting.
Design LED 60 TriStrip™ 17. TECHNICAL SPECIFICATIONS Power supply Power Requirements Fuse protection Power Consumption 98~240v 50/60Hz Internal Voltage Taps 120V = 4A/250V, GMA (5x20mm fine-wire fuse) 220V = 2A/250V, GMA (5x20mm fine-wire fuse) 250 (maximum @ at full power) Light Source Tri-Color LED 60 x 3-watt LEDs Life Time 50,000 Hours (Rated) Optical 62˚ (Standard - with frost filters) 48˚ (with frost filters removed) Color Mixing RGB Additive Color Mixing, 16.
Design LED 60 TriStrip™ ©Elation Professional, Los Angeles Ca. 41 www.ElationLighting.
Design LED 60 TriStrip™ ©Elation Professional, Los Angeles Ca. 42 www.ElationLighting.
Elation Professional 6122 S. Eastern Ave. Los Angeles, CA. 90040 323-582-3322 / 323-582-3108 fax www.ElationLighting.com /Info@ElationLighitng.com Rev.
