Design LED 60 Strip WA™ Elation Professional 6122 S Eastern Ave Los Angeles, Ca 90040 www.elationlighting.com Rev.
Design LED 60 Strip WA™ TABLE OF CONTENS CONTENTS 1. General Information……………………………………………………………………… 2 a. Introduction………………………………………………………………………. 2 b. Unpacking………………………………………………………..…………..…... 2 c. Customer Support…………………………………………….………………… 2 d. Warranty Registration……………………………………………………..……. 3 2. Safety Instructions………………………………………………………........…………. 4 3. Features…………………………………………………………………………………… 6 4. General Guidelines………………………………………………………………………. 7 5. Fixture Overview………………………………………………………………………….
Design LED 60 Strip WA™ 1. GENERAL INFORMATION INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable LED fixtures on the market today! The Design LED 60 Strip WA,™ has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit.
Design LED 60 Strip WA™ rain or moisture. Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself. Doing so will void your manufactures warranty. Please do not discard the shipping carton in the trash. Please recycle whenever possible. WARRANTY REGISTRATION: The Design LED 60 Strip WA™ carries a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase.
Design LED 60 Strip WA™ 2. SAFETY INSTRUCTIONS To guarantee proper and consistent operation, it is important to follow the guidelines in this manual. Elation Professional will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. Always be sure that the fan and the air inlets remain clean and are never blocked. Allow about 6” (15cm) between this fixture and other devices or a wall to allow for proper cooling. 2.
Design LED 60 Strip WA™ sure the power cord is never crimped or damaged. If the power cord is damaged, replace it immediately with a new one of similar power rating. 13. Always disconnect from main power before performing any type of service or any cleaning procedure. 14. Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion of the cord. 15. Please be aware that damages caused by modifications to the device are not subject to warranty.
Design LED 60 Strip WA™ 3.
Design LED 60 Strip WA™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, and other types of architectural installations. Do not attempt operation or installation without a proper knowledge on how to do so. This fixture was designed for indoor use only; use of this fixture outside will void the manufacture’s warranty. Consistent operational breaks will ensure that the fixture will function properly for many years to come.
Design LED 60 Strip WA™ 5. FIXTURE OVERVIEW 1. Bracket Locking Knob – This knob is used to secure the bracket in place after angle adjustments have been made. 2. Diffusing Lens – This lens is used to both protect the LEDs as well as diffuse the light output. 3. LED Assembly – LED assembly 3x1watt LEDs 4. DMX Input Jack – This jack accepts an incoming DMX signal via a male, 3-pin or a 5-pin XLR jack. 5.
Design LED 60 Strip WA™ as provides a female IEC connector for a power cord. Always replace the fuse with an exact match unless otherwise specified by an authorized Elation Service Technician. Using a fuse other than that specified could seriously damage the unit and will void your manufactures warranty. 8. On/Off Power Switch – Controls main power to the unit. 9. Dipswitch Assembly – These dipswitches are used to set the DMX address, master–slave settings, and other special functions.
Design LED 60 Strip WA™ 6. SET-UP AND INSTALLATION Yoke Assembly – Single Unit Operation (DLED 12 Brick shown for illustration purposes only). The device can be placed directly on the stage floor or rigged in any orientation on a truss without altering its operation characteristics. When connecting the hanging yoke to the fixture, refer to the illustration below.
Design LED 60 Strip WA™ Mounting points Overhead mounting requires extensive experience, including amongst others calculating working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury.
Design LED 60 Strip WA™ CAUTION! Be sure a qualified electrician performs all electrical connections before attempting any operation. Clamp Mounting The Design LED 60 Strip WA™ provides a unique mounting bracket assembly that allows the unit to stand on flat surface, hang on truss via a clamp, or be used in cluster allow multiple units to rigged together (see the illustration below).
Design LED 60 Strip WA™ Lens Removal and Replacement The front lens assembly may be removed to change the beam angle or to change the frost filters. The cover is conveniently attached with 1/4” twist lock Philips fasteners. To remove the top cover use a #2 Philips screwdriver and turn the 15 retaining fasteners counterclockwise. ©Elation Professional, Los Angeles Ca. 13 www.ElationLighting.
Design LED 60 Strip WA™ 7. UNDERSTANDING DMX Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): Your fixture and your DMX controller require a standard 3-pin or 5-pin XLR connector for data input and data output (see figure below). Be sure to only use properly rated DMX cables for DMX operation and not standrd audio cables.
Design LED 60 Strip WA™ (Please refer to the diagram below.). You can chain multiple moving heads together through serial linking. The cable needed should be two conductor, shielded cable with XLR input and output connectors. Always be sure daisy chain your in and out data connections, never split or “Y” your DMX connections unless you are using an approved DMX splitter such as the Elation Opto Branch 4™ or DMX Branch/4™.
Design LED 60 Strip WA™ be used, these adaptors are readily available at most electric stores. The chart on the next page details a proper cable conversion. Understanding Fixture DMX addressing; All fixtures should be given a DMX starting address when using a DMX controller, so the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control information sent out from the DMX controller.
Design LED 60 Strip WA™ fixture. In the case of the Design LED 60 Strip WA™, which is a 4 channel fixture (default), you should set the starting DMX address of the first unit to 1, the second unit to 5 (4 + 1), the third unit to 9 (4 + 5), and so on. The chart on page 24 details the proper starting DMX address dipswitch setting combination. NOTE: The Design LED 60 Strip WA contains a total of 12 dipswitches. Only use dipswitches 1~9 to set the DMX address.
Design LED 60 Strip WA™ 8. OPERATING MODES This fixture can run in two different DMX modes, the following pages will detail the different operating modes as well as how to achieve the different operating modes. DMX Settings: The chart below describes how to access the two different DMX modes. The chart below also defines how the channels will function in the different DMX modes.
Design LED 60 Strip WA™ This unit will keep and retain the last DMX command in the event of DMX signal failure. To reset the fixture you must turn the power off. DMX LED Indicator: The fixture has an LED indicator located by the dipswitches. This indicator has two functions as detailed below; 1) LED flashing green = No incoming DMX signal, fixture will function in stand-alone mode. Use the dipswitches to adjust the manual settings.
Design LED 60 Strip WA™ 9. DMX CHANNEL TRAITS 4 Channel Mode (default): This chart details a simple layout of the DMX channel assignment in 4-channel mode. CHANNEL 1: White CHANNEL 2: Amber CHANNEL 3: Strobe CHANNEL 4: Master Dimmer ©Elation Professional, Los Angeles Ca. 20 www.ElationLighting.
Design LED 60 Strip WA™ DMX channel’s functions and their values (4 Channel Mode - Default): Channel 1 - White: 0-255 White (0 = Black, 255 = 100% White) Channel 2 - Amber: 0-255 Amber (0 = Black, 255 = 100% Amber) Channel 3 - Strobe: 0 Normal Operation 1~95 Strobe effect slow to fast 96-127 No function 128-159 Pulse effect in sequences 160-191 No function 192-223 Random strobe effect slow to fast 224-255 No function Channel 4 – Master Dim This channel has two functions depending on the operati
Design LED 60 Strip WA™ 2 Channel Mode (user setting via dipswitch 12): This chart details a simple layout of the DMX channel assignment in 2-channel mode. CHANNEL 1: White CHANNEL 2: Amber DMX channel’s functions and their values (2 Channel Mode): Channel 1 - White: 0-255 White (0 = Black, 255 = 100% White) Channel 2 - Amber: 0-255 Amber (0 = Black, 255 = 100% Amber) ©Elation Professional, Los Angeles Ca. 22 www.ElationLighting.
Design LED 60 Strip WA™ ©Elation Professional, Los Angeles Ca. 23 www.ElationLighting.
Design LED 60 Strip WA™ 10. CLEANING AND MAINTENANCE The consider the following point during normal service and inspection: 1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall. 2. Electric power supply cables must not show any damage, material fatigue or sediments. Never remove the ground prong from the power cable.
Design LED 60 Strip WA™ 11. 2-YEAR LIMITED WARRANTY A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to be free of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
Design LED 60 Strip WA™ identifying marks to that effect. E. Elation Professional® reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above.
Design LED 60 Strip WA™ 12. PHOTOMETRIC DATA ©Elation Professional, Los Angeles Ca. 27 www.ElationLighting.
Design LED 60 Strip WA™ 13. DIMENSIONAL DRAWINGS ©Elation Professional, Los Angeles Ca. 28 www.ElationLighting.
Design LED 60 Strip WA™ 14. CIRCUIT SCHEMATIC ©Elation Professional, Los Angeles Ca. 29 www.ElationLighting.
Design LED 60 Strip WA™ 15. TECHNICAL SPECIFICATIONS Power supply: 100~240 AC, 50Hz~60Hz Power consumption: MAX. 140w LED Configuration: 60 1Watt Units (20 x Red, 20 x Green 20 x Blue) Packing dimensions: 174.5 x14.5x 21.5cm Weight: 10.5.
Design LED 60 Strip WA™ Elation Professional 4295 Charter Street Los Angeles, CA. 90058 323-582-3322 / 323-582-3108 fax www.ElationLighting.com /Info@ElationLighitng.com ©Elation Professional, Los Angeles Ca. 31 www.ElationLighting.
