Design Wash LED 60™ Elation Professional 6122 S Eastern Ave Los Angeles, Ca 90040 www.elationlighting.com Rev. 10/06/2009 – visage Version 1.
Design Wash LED 60™ ©Elation Professional, Los Angeles Ca. 2 www.ElationLighting.
Design Wash LED 60™ CONTENTS 1. General Information……………………………………………………………………… 4 a. Introduction………………………………………………………………………. 4 b. Unpacking………………………………………………………..…………..….. 4 c. Customer Support…………………………………………….………………… 4 d. Warranty Registration……………………………………………………..……. 5 2. Safety Instructions………………………………………………………........…………. 6 3. Features…………………………………………………………………………………… 7 4. General Guidelines………………………………………………………………………. 8 5. Fixture Overview…………………………………………………………………………. 9 6.
Design Wash LED 60™ 1. GENERAL INFORMATION INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable lighting fixtures on the market today! The Design Wash LED 60,™ has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit.
Design Wash LED 60™ yourself, doing so will void your manufactures warranty. Please do not discard the shipping carton in the trash. Please save for return shipping in the event service is ever needed or recycle the container whenever possible. WARRANTY REGISTRATION: The Design Wash LED 60™ carries a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase.
Design Wash LED 60™ 2. SAFETY INSTRUCTIONS The Design Wash LED 60™ is an extremely sophisticated piece of electronic equipment. To guarantee a smooth operation, it is important to follow the guidelines in this manual. Elation will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. Always be sure that the fan and the air inlets remain clean and are never blocked.
Design Wash LED 60™ 3. FEATURES • Pan 540° or 630˚ (User selectable) / Tilt 265° • 9˚ Beam Angle / 22˚ Field Angle • 60 x 3-Watt SSC LED Light Source – (22 x Red, 17 x Green, 15 x Blue, 6 x White) • 100,000 hours rated LED life • Smooth additive RGBW color mixing, 16.
Design Wash LED 60™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, etc. Do not attempt operation or installation without a proper knowledge on how to do so. This fixture was designed for indoor use only. Consistent operational breaks may ensure that the fixture will function properly for many years to come. Do not shake the fixture around. Avoid brute force when installing or operating the device.
Design Wash LED 60™ 5. FIXTURE OVERVIEW 1. LED Assembly 2. Yoke Assembly 3. Base 4. Carrying Handle 5. LCD Menu Display 6. Menu Button 7. Up Button 8. Down Button 9. Enter Button 10. Control Board Assembly 11. Cooling/Fan Assembly 12. 3-Pin DMX Output 13. Battery On/Off Button 14. 3-Pin DMX Input 15. Fuse Holder 16. Power Cord 17. 5-Pin DMX Output 18. 15-Pin DMX Input ©Elation Professional, Los Angeles Ca. 9 www.ElationLighting.
Design Wash LED 60™ 1. LED Assembly – 60 Philips Rebel LEDs comprise the LED assembly. 22 Red, 17 Green, 15 Blue, and 6 White. 2. Yoke Assembly – This assembly consist of the electronics and motors that control the tilt movement as well as the LED operation. 3. Base Assembly – The base assembly holds and protects all the relative electronics. Avoid bruit force to base as this may seriously effect the operation of this fixture. 4.
Design Wash LED 60™ 12. 3-Pin DMX Output Jack – This jack is used to send an incoming DMX signal to the next fixture in the DMX chain via a female, 3-pin XLR jack. 13. Battery On/Off Button – This button is used to turn the display menu on or off when the fixture is not plugged into power. This feature will allow the fixture’s DMX address and wireless setting to be set when the fixture is not connected to a power source. 14.
Design Wash LED 60™ 6. MOUNTING AND INSTALLATION Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, or in areas were the fixture might be reached by unauthorized personal. Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device’s weight. Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable.
Design Wash LED 60™ Mounting points Overhead mounting requires extensive experience, including amongst others calculating working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury. CAUTION! Be sure a qualified electrician performs all electrical connections.
Design Wash LED 60™ power cord to the appropriate wall outlet. Clamp Mounting The Design Wash LED 60™ provides a unique mounting bracket assembly that integrates the bottom of the base, the included “Omega Bracket,” and the safety cable rigging point in one unit (see the illustration below). When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the “omega bracket”.
Design Wash LED 60™ 7. UNDERSTANDING DMX DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. DMX allows all makes and models of different manufactures to be linked together and operate from a single controller. This is possible as long as all the fixtures and the controller are DMX compliant.
Design Wash LED 60™ must be daisy chained and cannot be split, unless using an approved DMX splitter such as the Elation Opto Branch 4™ or DMX Branch/4™. Be sure to follow the above figure when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior.
Design Wash LED 60™ DMX-512 connection with DMX terminator A DMX terminator should be used in all DMX lines especially in longer runs. The use of a terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line.
Design Wash LED 60™ out from the DMX controller. The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the base of the fixture. You can set the same starting address for all fixtures or a group of fixtures, or set different address for each individual fixture.
Design Wash LED 60™ 8. FIXTURE MENU On-Board System Menu: The Design Wash LED 60™ comes with an easy to navigate system menu. This next section will detail the functions of each command in the system menu. To access display Menu via the internal battery, press the UP & DOWN buttons simultaneously. Display will automatically switch off after about 10 seconds from last button press.
Design Wash LED 60™ Function Mode Default settings shaded.
Function Effect Adjust Reset Design Wash LED 60™ Reset All Reset all motors Reset Pan&Tilt Reset Pan/Tilt Test Channel PAN …… Manual Control PAN PAN =XXX : : --Password-- Password=XXX Calibrate and adjust the PAN PAN=XXX effects : : position.
Design Wash LED 60™ unique starting address. The addressing feature is what allows DMX to function properly. The DMX address of a fixture is what allows it to communicate with a controller properly. The DMX addressing also allows the fixture to ignore any DMX information coming from the controller that is not meant specifically for the fixture. Because each fixture is connected in a daisy-chain fashion it is imperative to assign a proper and unique starting DMX address to each and every fixture.
Design Wash LED 60™ 8.2 Information: 8.2.1 Time information These functions will detail different time functions associated with the fixture. Current Time This function displays the running time of the fixture from the last power on. The display shows “XXXX”, where “XXXX” represents the number of hours the fixture has been running. This counter is automatically reset after every power-on. Total Life Hours This function tracks the total running time of the fixture from the very first start-up.
Design Wash LED 60™ temperature readout is user selectable for either Celsius or Fahrenheit. 8.2.3. Software version This function will display the current operating software version of the fixture. • Select “Software Version” in the system menu. • Press enter to confirm. • The LCD will read “V-X.X”, “X.X” represents the version number, e.g. “V-1.0”, “V-2.6”. • Use the UP and DOWN buttons to toggle through the software version of different IC’s. • Press the Mode/Esc-button to return to the main menu. 8.
Design Wash LED 60™ Tilt Reverse - This function allows you to invert all tilt movements. Use the Up and Down buttons to turn this function On or Off. Press the Enter button to accept the change or the Mode button to cancel and return to the main menu. This function is “OFF” by default. Fine Resolution – This function changes the DMX channel operation from 8bit (11 channels) to 16bit (13 channels). This function is “on” by default, which allows for the “Pan Fine” and “Tilt Fine” channels to be accessed.
Design Wash LED 60™ sensitive to sound. This function only works in conjunction with the sound active modes. The default setting is 70% and setting range from 0% to 99%. 8.4.2 Service Setting – The adjustments and settings in this section should only be performed by a technician familiar with the functionality of fixtures of this type. Incorrect adjustments to these functions may result reduced performance or damage to the fixture.
Design Wash LED 60™ 8.4.6 Initial effect – This function allows a user to create and assign a custom “Home Position.” Adjusting the Pan and Tilt values then locking those values into the fixture’s internal memory creates the new “Home” position. Restoring the fixture’s factory values can erase this setting. 8.4.7 Restore Default – This function is used to restore the factory settings of the device. All settings will be set back to the default values (shaded). Any edited scenes will be lost. 8.
Design Wash LED 60™ customer support team for step-by-step instructions. 8.7 User Mode Set: 8.7.1 User Mode - This function allows the DMX channels assignment to be changed from the default value of 13, to either 8bit/11 channels or extended mode at 13 channels. This function also allows the user to create user defined channel orders allowing the fixture to match the channel order of other fixtures on the market for easier operation.
Design Wash LED 60™ 9. DMX ADDRESSING Setting the DMX address - After the fixture is turned “ON” it will immediately complete a reset process that test all the fixture’s functions. When the reset process concludes the LCD will display the fixture’s current DMX address. If the fixture is not receiving a DMX signal, the display will flash continuously. To set or adjust a DMX address, please follow the procedure below: 1.
Design Wash LED 60™ 6. Press ENTER to confirm. 7. Press MODE/ESC to return to the main menu. Controller Settings: 1. Set the DMX value of channel 1 to a value of 7. 2. Set the DMX value of channel 2 to a value of 7 or 8. When channel 2 is set to "7" you can adjust the starting address between 1 and 255. When set to "8" you can adjust the starting address between 256 and 511. 3. Use channel 3 to set your desired DMX starting address.
Design Wash LED 60™ 10. OPERATION Operating Modes: The Design Wash LED 60™ can operate in six different modes. This next section will detail the differences in the operating modes. • Auto Program Mode (Master) - The fixture will chase through the built-in programs, sending a DMX control signal to all other fixtures connect via DMX cables instruction for a synchronized light show. • Auto Program Mode (Stand-alone) - The fixture will chase through the built-in program.
Design Wash LED 60™ Control” submenu. See page 19 for the menu breakdown. Once in the “Music Control” submenu select “Alone” 10.2 Master/Slave Operation (Auto Program or Music Control): This function allows up to 16 fixtures to be linked together to provide a synchronized light show without the use of a controller. Only use this when linking several Design Wash LED 60™ together for use without a controller. Any fixture can act as a “Master or a “Slave.
Design Wash LED 60™ 11. WORKING WITH BUILT-IN PROGRAMS The fixture comes equipped with a built-in DMX recorder that allows custom programs to be installed and recalled directly from the fixture’s control board. Programs can be created and stored using the fixture’s control board or by using an external DMX controller. The following instructions will detail the procedures for using the on-board system menu as well as using a DMX compliant controller.
Design Wash LED 60™ functions listed below: - “Auto Program” – Allows access to all 16 of the channel’s DMX traits. - “PAN” – pan movement. - “PAN-Fine” – precision pan movement. - “TILT” – tilt movement.
Design Wash LED 60™ • Then tap the “ENTER” button and toggle to “Program 1” menu function 8-2-1. • When you get to the “Program 1” function tap the “ENTER” button. The screen will then change to Edit Steps 01, this will be menu function 8-2-1-1. Use the “UP” and “DOWN” buttons to toggle through the scenes created in “Step 1.” Press the “ENTER” button to add a scene to the program. Tapping the “Enter” button will automatically lock the selected scene into the programs’ memory.
Design Wash LED 60™ 12. DMX CHANNEL TRAITS: The chart below details the channel layout for 13 DMX channels (default). In 8-bit mode the “Pan Fine” and “Tilt Fine” channels are not used, thus converting the fixture into a 11-channel DMX fixture. CHANNEL 1: Pan Movement (max. 540° or 630˚ User Selectable) CHANNEL 2: 16bit Pan Movement (pan fine) CHANNEL 3: Tilt Movement (max.
Design Wash LED 60™ DMX channel function and values: DMX channel values (13 DMX channels): Mode/Channel St Ba 1 1 2 3 2 0-255 0-255 0-255 5 3 6 4 7 5 8 6 9 7 10 8 9 Function Ex 0-255 4 11 Value 0-255 0-255 0-255 0-255 0-31 32-63 64-95 96-127 128-159 160-191 192-223 224-255 0-255 0-7 8-39 40-71 72-103 104-135 136-167 168-199 200-231 232-255 PAN Movement 8bit: Pan Movement Pan Fine 16bit Fine control of Pan movement TILT Movement 8bit: Tilt Movement Tilt Fine 16bit Fine control of
Design Wash LED 60™ 12 13 10 11 0-225 226-235 236-255 0-79 80-84 85-87 88-99 100-119 120-139 140-159 160-179 180-199 200-219 220-239 240-255 Speed Pan/Tilt movement: Max to min speed Blackout by movement No function Lamp on/off, reset, internal programs: Normal All motor reset Scan motor reset No function Internal program 1 (secne1~8 of EEPROM) Internal program 2 (secne9~16 of EEPROM) Internal program 3 (secne17~24 of EEPROM) Internal program 4 (secne25~32 of EEPROM) Internal program 5 (secne33~40 of
Design Wash LED 60™ 13. ERROR CODES: When power is applied, the unit will automatically enter a “reset/test” mode. This mode brings all the internal motors to a home position. If there is an internal problem with one or more of the motors an error code will flash in the display in the form of “XXer” were as XX will represent a function number. For example, when the display shows “0Er,” it means there is some type of error with the Pan motor.
Design Wash LED 60™ 14. CLEANING AND MAINTENANCE The following points have to be considered during the inspection: 1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall. 2. There must not be any deformations on the housing, lenses, rigging hardware and rigging points (ceiling, suspension, trussing).
Design Wash LED 60™ 15. Photometric Data: ©Elation Professional, Los Angeles Ca. 41 www.ElationLighting.
Design Wash LED 60™ 16. DIMENSIONAL DRAWINGS: ©Elation Professional, Los Angeles Ca. 42 www.ElationLighting.
Design Wash LED 60™ 17. CIRCUIT SCHEMATICS ©Elation Professional, Los Angeles Ca. 43 www.ElationLighting.
Design Wash LED 60™ 18. 2-YEAR LIMITED WARRANTY A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to be free of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
Design Wash LED 60™ E. Elation Professional® reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above.
Design Wash LED 60™ 19. TECHNICAL SPECIFICATIONS Power supply Power Requirements Fuse protection 100~240v 50/60Hz Internal Voltage Taps Power Consumption 120V = 3.15A/250V, GMA (5x20mm fine-wire fuse) 220V = 2A/250V, GMA (5x20mm fine-wire fuse) 235 (maximum @ at full power) Light Source – SSC Red LED Green LED Blue LED White LED Life Time 22 3watt Rebel LED 17 3watt Rebel LED 15 3watt Rebel LED 6 3watt Rebel LED 100,000 Hours (Rated) Optical 9˚ Beam Angle / 7370 Lux @ 2.
Design Wash LED 60™ ©Elation Professional, Los Angeles Ca. 47 www.ElationLighting.
Elation Professional® 6122 S. Eastern Ave. Los Angeles, CA. 90040 323-582-3322 / 323-832-9142 fax www.ElationLighting.com / Info@ElationLighitng.com Version 1.
