Design LED 12 Brick II Elation Professional™ 6122 S. Eastern Ave. Los Angeles, CA. 90040 www.elationlighting.com Rev.
Design LED 12 Brick II ™ TABLE OF CONTENS CONTENTS 1. General Information……………………………………………………………………… 2 a. Introduction………………………………………………………………………. 2 b. Unpacking………………………………………………………..…………..… 2 c. Customer Support…………………………………………….………………… 2 d. Warranty Registration……………………………………………………..…… 3 2. Safety Instructions………………………………………………………........…………. 4 3. Features……………………………………………………………………………………6 4. General Guidelines………………………………………………………………………. 7 5. Fixture Overview………………………………………………………………………….
Design LED 12 Brick II ™ 1. GENERAL INFORMATION INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable LED fixtures on the market today! The Design LED 12 Brick II ™, has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit.
Design LED 12 Brick II ™ rain or moisture. Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself. Doing so will void your manufactures warranty. Please do not discard the shipping carton in the trash. Please recycle whenever possible. WARRANTY REGISTRATION: The Design LED 12 Brick II ™ carries a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase.
Design LED 12 Brick II ™ 2. SAFETY INSTRUCTIONS To guarantee proper and consistent operation, it is important to follow the guidelines in this manual. Elation Professional will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. Always be sure that the fan and the air inlets remain clean and are never blocked. Allow about 6” (15cm) between this fixture and other devices or a wall to allow for proper cooling. 2.
Design LED 12 Brick II ™ sure the power cord is never crimped or damaged. If the power cord is damaged, replace it immediately with a new one of similar power rating. 13. Always disconnect from main power before performing any type of service or any cleaning procedure. 14. Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion of the cord. 15. Please be aware that damages caused by modifications to the device are not subject to warranty.
Design LED 12 Brick II ™ 3.
Design LED 12 Brick II ™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, and other types of architectural installations. Do not attempt operation or installation without a proper knowledge on how to do so. This fixture was designed for indoor use only; use of this fixture outside will void the manufacture’s warranty. Consistent operational breaks will ensure that the fixture will function properly for many years to come.
Design LED 12 Brick II ™ 5. FIXTURE OVERVIEW 3 2 1 4 5 6 8 7 9 10 11 12 13 14 1. Bracket Locking Knob – This knob is used to secure the bracket in place after angle adjustments have been made. 2. Diffusing Lens – This lens is used to both protect the LEDS as well as diffuse the light output. 3. LED Assembly – RGB LED assembly 3x1watt LEDS ©Elation Professional, Los Angeles Ca. 8 www.ElationLighting.
Design LED 12 Brick II ™ 4. On/Off Power Switch – Controls main power to the unit. 5. Power Output Jack – Use this jack to jump power to another Design LED 12 Brick II ™ 6. Power Input/Fuse Holder Assembly – This assembly holds the safety fuse as well as provides a female IEC connector for a power cord. Always replace the fuse with an exact match unless otherwise specified by an authorized Elation Service Technician.
Design LED 12 Brick II ™ 14. ENTER BUTTON – This button is used to select and confirm a menu function. ©Elation Professional, Los Angeles Ca. 10 www.ElationLighting.
Design LED 12 Brick II ™ 6. MOUNTING AND INSTALLATION Yoke Assembly – Single Unit Operation (DLED 12 Brick shown for illustration purposes only). The device can be placed directly on the stage floor or rigged in any orientation on a truss without altering its operation characteristics. When connecting the hanging yoke to the fixture, refer to the illustration below.
Design LED 12 Brick II ™ Overhead mounting requires extensive experience, including amongst others calculating working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury.
Design LED 12 Brick II ™ CAUTION! Be sure all electrical connections are performed by a qualified electrician before attempting any operation. Clamp Mounting The Design LED 12 Brick II ™ provides a unique mounting bracket assembly that allows the unit to stand on flat surface, hang on truss via a clamp, or be used in cluster allow multiple units to rigged together (see the illustration below).
Design LED 12 Brick II ™ Securing the Design LED 12 Brick II ™ Always secure your fixture with a safety cable when suspend-ing the unit from truss or other means. The fixture provides a built-in rigging point for a safety cable as illustrated above. Be sure to only use the designated rigging point for a safety cable. Never secure a safety cable to the hanging bracket. ©Elation Professional, Los Angeles Ca. 14 www.ElationLighting.
Design LED 12 Brick II ™ 7. UNDERSTANDING DMX Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): Your fixture and your DMX controller require a standard 3-pin XLR connector for data input and data output (see figure below). Be sure to only use properly rated DMX cables for DMX operation and not standrd audio cables.
Design LED 12 Brick II ™ 4™ or DMX Branch/4™. CONTROLLER Please note: to ensure maximal stability, only two devices may be connected together in this manner! From the third devices, please connect to power supply to get power for the second link. DMX-512 connection with DMX terminator When longer runs of cable are used, you may need to use a terminator on the last fixture to avoid erratic behavior.
Design LED 12 Brick II ™ 5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart on the next page details a proper cable conversion.
Design LED 12 Brick II ™ 8. OPERATING MODES This fixture can run in three different DMX modes, the following pages will detail the different operating modes as well as how to achieve the different operating modes. DMX Settings: The chart below describes how to access the different DMX modes. The chart below also defines the how the channel will function in the different DMX modes.
Design LED 12 Brick II ™ 224---255 Open If running the internal program, the tailender channel would be the speed of grogram from slow to fast. If not running the internal program, the tailender channel would be dimmer channel. 2：Display menu： MODE MANU RED Set DMX address Select 3 channel mode Select 4 channel mode Select 12 channel mode Select 15 channel mode Run as slave.
Design LED 12 Brick II ™ CHS7 OTHR SOND CHS8 CTRL MIC FADE XXX Adjust speed of fade STRB SPED FADE STRB SPED FADE STRB MAST ALON M-XX MOD1 MOD2 XXX XXX XXX XXX XXX XXX XXX Adjust speed of strobe Adjust speed of scene Adjust speed of fade Adjust speed of fade Adjust speed of scene Adjust speed of fade Adjust speed of fade Sound-controlled run as Master Sound-controlled run in Stand Alone Microphone sensitivity Select standard dimmer Select weak dimmer Reset to Fixture to the Fa
Design LED 12 Brick II ™ DMX Operation Notes: The fixture will automatically function in DMX mode whenever the unit receives a DMX signal. Please note that this will override all manual settings regardless of dipswitch positions. This unit will keep and retain the last DMX command in the event of DMX signal failure. To reset the fixture you must turn the power off. ©Elation Professional, Los Angeles Ca. 21 www.ElationLighting.
Design LED 12 Brick II ™ 9. DMX CHANNEL TRAITS 4 Channel Mode: This chart details a simple layout of the DMX channel assignment in 4-channel mode. The chart traits will vary slightly for 3-channel, 12-chennel, and 15-channel operation, as those modes use more RGB channels for more precise control. 1 2 3 4 CHANNEL 1: Red CHANNEL 2: Green CHANNEL 3: Blue CHANNEL 4: Dimming (0%-100%) ©Elation Professional, Los Angeles Ca. 22 www.ElationLighting.
Design LED 12 Brick II ™ DMX channel’s functions and their values (4 Channel Mode): Channel 1 - Red: 0-255 Red (0-Black, 255-100% Red) Channel 2 - Green: 0-255 Green (0-Black, 255- 100% Green) Channel 3 - Blue: 0-255 Blue (0-Black, 255- 100% Blue) Channel 4 - General dimming 0-255 Dimming (0%-100%) ~ Normal Operation ©Elation Professional, Los Angeles Ca. 23 www.ElationLighting.
Design LED 12 Brick II ™ 10. CLEANING AND MAINTENANCE The consider the following point during normal service and inspection: 1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall. 2. Electric power supply cables must not show any damage, material fatigue or sediments. Never remove the ground prong from the power cable.
Design LED 12 Brick II ™ 11. 2-YEAR LIMITED WARRANTY A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to be free of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
Design LED 12 Brick II ™ effect. E. Elation Professional® reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above.
Design LED 12 Brick II ™ 12. PHOTOMETRIC DATA Beam angle 44° Intensity（LUX） 480 144 Distance (m) 0 Diameter (m) 0 1 0.8 2 1.6 ©Elation Professional, Los Angeles Ca. 27 76 3 2.4 www.ElationLighting.
Design LED 12 Brick II ™ 15. DIMENSIONAL DRAWINGS 14. CHANGE LENS TO GET DIFFERENT BEAM ANGLES ©Elation Professional, Los Angeles Ca. 28 www.ElationLighting.
Design LED 12 Brick II ™ 15. CIRCUIT SCHEMATIC ©Elation Professional, Los Angeles Ca. 29 www.ElationLighting.
Design LED 12 Brick II ™ 16. TECHNICAL SPECIFICATIONS Power supply: 100V~240V AC, 50Hz~60Hz Power consumption: MAX LED Configuration: 12 1Watt Units (4 x Red, 4x Green 4 x Blue) Packing dimensions: 47x26.5x16cm (57x47x36cm ~ 4pc system) Weight: 3.5Kgs / 7.
Design LED 12 Brick II ™ Elation Professional 6122 S. Eastern Ave. Los Angeles, CA. 90040 323-582-3322 / 323-582-3108 fax www.ElationLighting.com /Info@ElationLighitng.com ©Elation Professional, Los Angeles Ca. 31 www.ElationLighting.
