DLED Par Zoom Elation Professional™ 6122 S. Eastern Ave. Los Angeles, Ca 90040 www.elationlighting.com Rev. 07/20/2010 –visage Version 1.
DLED Par Zoom™ ©Elation Professional, Los Angeles Ca. 1 www.ElationLighting.
DLED Par Zoom™ TABLE OF CONTENS 1. General Information… … … … … … … … … … … … … … … … … … … … … … … … … … … 3 a. Introduction……………………………………………………………………….3 b. Unpacking… … … … … … … … … … … … … … … … … … … … … . . … … … … . . … c. Customer Support……… … … … … … … … … … … … … … … . … … … … … … … 3 d. Warranty Registration……………………………………………………..…… 3 3 2. Safety Instructions………………………………………………………........………….5 3. F e a t u r e s … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … …7 4.
DLED Par Zoom™ 1. GENERAL INFORMATION INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable LED fixtures on the market today! The DLED PAR ZOOM™ has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance.
DLED Par Zoom™ yourself. Doing so will void your manufactures warranty. Please do not discard the shipping carton in the trash. Please recycle whenever possible. WARRANTY REGISTRATION: The DLED PAR ZOOM™ carries a two-year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre -paid and accompany a return authorization (R.A.) number. The R.A.
DLED Par Zoom™ 2. SAFETY INSTRUCTIONS To guarantee proper and consistent operation, it is important to follow the guidelines in this manual. Elation Professional will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. Always be sure that the fan and the air inlets remain clean and are ne ver blocked. Allow about 6”(15cm) between this fixture and other devices or a wall to allow for proper cooling. See page 12.
DLED Par Zoom™ 12. Always disconnect from main power before performing any type of service or any cleaning procedure. 13. Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion of the cord. 14. This fixture is designed for use indoors only, use of this fixture outdoors will void the manufactures warranty. 15. Please be aware that damages caused by modifications to the device are not subject to warranty.
DLED Par Zoom™ 3.
DLED Par Zoom™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, and other types of architectural installations. Do not attempt operation or installation without a proper knowledge on how to do so. Consistent operational breaks will ensure that the fixture will function properly for many years to come. Do not shake the fixture around. Avoid brute force when installing or operating the fixture.
DLED Par Zoom™ 5. FIXTURE OVERVIEW 1) Fixture Casing 2) LED Assembly 3) Yoke Assembly 4) Menu Button 5) Up Button 6) Down Button 7) Enter Button 8) Power input 9) DMX Output Jack 10) DMX Input Jack 1. Fixture Casing Assembly – Durable cast aluminum casing designed to take the rigors of touring. ©Elation Professional, Los Angeles Ca. 9 www.ElationLighting.
DLED Par Zoom™ 2. LED Lens Assembly –The lens assembly may be user replaced in the event repair is needed or a different beam angle is required. 3. Yoke Assembly – This yoke is designed to perform two functions; 1) When split it can be used as a floor stand. 2) Used to secure a mounting clamp for truss mounting. 4. MENU Button – This button is used to access the fixtures menu functions. 5. Up Button – The up button is used to toggle forward through the menu functions and settings. 6.
DLED Par Zoom™ 6. MOUNTING AND INSTALLATION Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, and away from areas were unauthorized personnel might reach the fixture. Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device’s weight. Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable.
DLED Par Zoom™ Mounting The DLED PAR ZOOM™ is fully operational in any mounting position, hanging upside-down, side mounted, or set on a flat level surface, etc. Be sure this fixture is kept at least 0.5m (1.5 feet) away from any flammable materials (decoration etc.). When clamp mounting; always use and install the supplied safety cable as an added safety measure to prevent accidental damage in the event of a clamp failure. See the image below.
DLED Par Zoom™ the safety guidelines in this manual to avoid damage to the unit and/or personal injury. When mounting this fixture to truss be sure to secure an appropriately rated clamp to the hanging yoke using a M12 screw fitted through the center hole of the hanging yoke. As an added safety measure be sure to attach at least one properly rated safety cable to the fixture. See illustrations below.
DLED Par Zoom™ 7. UNDERSTANDING DMX DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. DMX allows all makes and models of different manufactures to be linked together and operate from a single controller. This is possible as long as all the fixtures and the controller are DMX compliant.
DLED Par Zoom™ Be sure to follow the above figure when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’ s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’ s outer casing. Grounding the shield could cause a short circuit and erratic behavior.
DLED Par Zoom™ DMX-512 connection with DMX terminator A DMX terminator should be used in all DMX lines especially in longer runs. The use of a terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line.
DLED Par Zoom™ out from the DMX controller. The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the back of the fixture. You can set the same starting address for all fixtures or a group of fixtures, or set different address for each individual fixture.
DLED Par Zoom™ The DLED PAR ZOOM ™ has a LED indicator on the display. This indicator is designed to give a quick visual indication of the fixtures’DMX status. The illustration below details the functionality of the LED indicators. The LED indicator represents DMX signal: • If the indicators is on, a clean DMX signal is present • If the indicator is off, there is no DMX signal present ©Elation Professional, Los Angeles Ca. 18 www.ElationLighting.
DLED Par Zoom™ 9. DISPLAY MENU On-Board System Menu: The Design PAR Zoom™ comes with an easy to navigate system menu. This next section will detail the func tions of each command in the system menu. LED Control Panel: The control panel located on the base of the fixture allows you to access the main menu and make all necessary adjustments to the Design Par Zoom™ . During normal operation, tapping the “MENU”key once will access the fixture’s main menu.
DLED Par Zoom™ VALU DISP MIC FAIL FLIP D ON LOCK M-XX OFF/HOLD/ AUTO/SOUN MAST (SO-M) D–XX (DXXX) ON/OFF ON/OFF ON/OFF Sound-controlled Run as Master D-00 Display the DMX 512 value of each channel Reverse display Shut off LED display Key lock (Hold the MENU button for 3 seconds to reactivate ) Mic sensitivity No DMX Status REST 1 SET 2 MANL 3 TIME 4 EDIT Reset Restore factory settings Preserves manual setting after power has been turned off.
DLED Par Zoom™ Remarks: 1) If the fixture does not receive a DMX signal the menu display will flash repeatedly. 2) TIME: Adjust the hold time for each scene in built-in chase programs. 3) FADE: Adjust the fade time between each scene in the built-in programs. 9.1 “MODE”- Function Mode: 9.1.1 - DMX address setting – This function is used to set or adjust the fixture’ s starting DMX address. E very device controlled by DMX has to have a unique starting address.
DLED Par Zoom™ 9.1.2 - Internal Program Settings This function allows the internal programs to run in either stand-alone or master/salve mode. In “Master”mode the fixture will send DMX data to other fixtures connect via the DMX chain. In “Alone”mode the fixture will operate as a single fixture. The program for this mode is selected in the “Select program” section of the control menu. You can set the number of steps under “Edit program”. You can edit the individual scenes under “Edit scenes”.
DLED Par Zoom™ 9.2 “SET”–Fixture Personality Settings: These functions set specific running modes and operating parameters. Microphone Sensitivity This function adjusts the sensitivity of the built-in microphone. The fixture uses the built-in microphone to trigger the built-in programs to sound. DMX Fault Protection This function dictates how the fixture will operate in the event DMX signal is suddenly lost while operating in DMX mode.
DLED Par Zoom™ 9.4 “TIME” – Operating Hours These functions will detail different time functions associated with the fixture. (0000~9999 Hours) This function tracks the running time of the fixture from the point it was last cleared. Where “XXXX ”represents the total number of running hours. This time is none destructive and will remain in the fixtures memory indefinitely. Use this time to track rentals or show durations. Clear Fixture Run Time This function resets the run time to zero.
DLED Par Zoom™ 10. DMX ADDRESSING Setting the DMX address - After the fixture is turned “ON”it will immediately complete a reset process that test all the fixture’s functions. When the reset process concludes the LCD will display the fixture’ s current DMX address. If the fixture is not receiving a DMX signal, the display will flash continuously. To set or adjust a DMX address, please follow the procedure below: 1.
DLED Par Zoom™ 6. Press ENTER to confirm. 7. Press MENU to return to the main menu. 8. Note: This function is active by default. Controller Settings: 1. Set the DMX value of channel 1 to a value of 7. 2. Set the DMX value of channel 2 to a value o f 7 or 8. When channel 2 is set to "7" you can adjust the starting address between 1 and 255. When set to "8" you can adjust the starting address between 256 and 511. 3. Use channel 3 to set your desired DMX starting address.
DLED Par Zoom™ 11. DMX TRAITS DMX Operation Notes: The fixture will function in DMX mode whenever the unit is receiving a DMX signal. Please note that this will override all manual settings. This unit will keep and retain the last DMX command in the event of DMX signal failure. To reset the fixture you must turn the power off. DMX CHANNEL TRAITS The chart below outlines the different DMX. ©Elation Professional, Los Angeles Ca. 27 www.ElationLighting.
DLED Par Zoom™ DMX channel functions and their values (8 DMX channels): Channel Value Red: 1 0-255 Red (0-Black, 255-100% Red) Green: 2 0-255 3 Function Green (0 -Black, 255-100% Green) Blue: 0-255 4 Blue (0-Black, 255- 100% Blue) Color macros: 0 No function 1-7 R02 Bastard Amber 8-15 R04 Medium Amber 16-23 R09 Pale Amber Gold 24-31 R316 Gallo Gold 32-39 R21 Golden Amber 40-47 R26 Light Red 48-55 R27 Medium Red 56-63 R36 Medium Pink 64-71 R339 Broadway Pink 72-79 R344 Follies
DLED Par Zoom™ 160-167 R76 Light Green Blue 168-175 R79 Bright Blue 176-183 R80 Primary Blue 184-191 R382 Congo Blue 192-199 R87 Pale Yellow Green 200-207 R89 Moss Green 208-215 R91 Primary Green 216-223 L200 Double CTB 224-231 L201 Full CTB 232-239 L202 1/2 CTB 240-247 L119 Dark Blue 248-255 White Internal programs: 5 0-10 No Function 11-40 Internal program 1 41-70 Internal program 2 71-100 Internal program 3 101-130 Internal program 4 131-160 Internal program 5 161-190 Internal program 6 191-22
DLED Par Zoom™ General dimming/speed: 0-255 7 Dimming (0-Black, 255- 100% ) Speed from slow to fast /when running internal programs Speed from slow to fast /when running gradient effect Zoom: 8 0-255 Continuous adjustment from far to near ©Elation Professional, Los Angeles Ca. 30 www.ElationLighting.
DLED Par Zoom™ 12. WORKING WITH BUILT-IN PROGRAMS The fixture comes equipped with a built-in DMX recorder that allows custom programs to be installed and recalled directly from the fixture’s control board. Programs can be created and stored using the fixture’s control board or by using a n external DMX controller. The following instructions will detail the procedures for using the on-board system menu as well as using a DMX compliant controller. - Main menu 4 1.
DLED Par Zoom™ 2. Press [ENTER], the display shows “RE.XX”, “XX”stands for the number from 1 to 400. 3. Press [ENTER] to confirm or Press [MENU ] to return to the main menu. Memory Statistics: Quick Access Programs (Program Part): 3 Total Number of Programs: 10 Maximum Number of Steps (Scenes) per a Program: 64 Total Number of Scenes (Steps): 250 Step 1 –Building Scenes via Fixture Control Board. The control will store a maximum of 48 scenes. These scenes are then used to create the programs.
DLED Par Zoom™ 11. Press [ENTER] to edit the time needed, the display shows “TXXX”, “XXX”stands for the time needed to run the current scene, value “001-999”. E.g., “002”means you need 0.4ms (002*0.2ms) to run the current scene. Adjust the desired time by pressing [UP] or [DOWN] button. 12. Press [ENTER] to save the settings for the scene you are editing, the display will change to the next scene automatically. 13. Repeat steps 3-14 to edit and other scenes, you can edit and save a maximum of 48 scenes.
DLED Par Zoom™ 13. BARN DOOR / FILTER INSTALLATION The DLED PAR ZOOM can be fitted with a barn door and gel frame for a frost filter. The instructions listed below will detail the procedure for installing both options. 1. To install the gel frame holder only, simply rotate the retaining clip up and insert the gel frame, then rotate the retaining clip down again to secure the gel frame in place. 2.
DLED Par Zoom™ 14. CLEANING AND MAINTENANCE Consider the following points during normal service and inspection: 1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall. 2. Electric power supply cables must not show any damage, material fatigue or sediments. Never remove the ground prong from the power cable.
DLED Par Zoom™ 15. 2-YEAR LIMITED WARRANTY A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to be free of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
DLED Par Zoom™ effect. E. Elation Professional® reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above.
DLED Par Zoom™ 16. PHOTOMETRIC DATA ©Elation Professional, Los Angeles Ca. 38 www.ElationLighting.
DLED Par Zoom™ ©Elation Professional, Los Angeles Ca. 39 www.ElationLighting.
DLED Par Zoom™ 17. DIMENSIONAL DRAWINGS ©Elation Professional, Los Angeles Ca. 40 www.ElationLighting.
DLED Par Zoom™ 18. CIRCUIT SCHEMATIC ©Elation Professional, Los Angeles Ca. 41 www.ElationLighting.
DLED Par Zoom™ 19. TECHNICAL SPECIFICATIONS Power supply: 100v~240v / 50Hz~60Hz AC Power consumption: Maximum 120w IP Grade: IP20 LED Configuration: 36 x 3 Watt (10 x Red, 16 x Green, 10 x Blue) Weight: 7 Kgs / 15.4Lbs DMX Channels: 8 DMX Drive: Standard DMX-512, 3 pole IP Rated Locking Connector; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1. Color Mixing: RGB Color Additive Mixing Beam Angle: Variable 13°~ 55° Fuse: GMA 220v~3.
Elation Professional 6122 S. Eastern Ave. Los Angeles, CA. 90040 323-582-3322 / 323-832-9142 fax www.ElationLighting.com / Info@ElationLighitng.com Rev. 07/20/2010 –visage Version 1.
