Specifications

©2011 ELAN HOME SYSTEMS • CARLSBAD, CA USA • ALL RIGHTS RESERVED
70
General Products
SPECIFICATIONS
Input Level . . . . . . . . . . . . . .0 – 2V RMS
Gain . . . . . . . . . . . +1dB at Source plate,
. . . . . . . . . . . . . . -1dB at S12, 0dB total
Freq. Resp. . . . . . . 20Hz to 20kHz, +/-0.5dB
THD + Noise . . . . . . . . . . . . . . <0.01%
IR Output Level . . . . . . . . . . . . . . +12V
IR Bandwidth. . . . . . . . . . . . . . . 100kHz
Wire Requirements . . . . . . (Audio / IR) Cat-5,
. . . . . . . . . . . . . . . (Video) RG-6 Coax
Style . . . . . . . . . White Decora®-style only
Designed for use with the
S128P’s eight Local Source
Inputs, the LSWP sends audio
from any local source (e.g.
a CD player in the Master
Bedroom) back down to the
S128P, and IR control signals
from the S128P back to the
local source.
Audio and IR are transmitted over a single run of
Cat-5. Balanced differential line drivers ensure
noise-free audio from sources located up to 300
ft. from the S128P. An IR OUT jack allows you to
connect an IR emitter (included) for control of the
source from that zone.
Kit includes:
• (1) Local Source Wall Plate
• (1) IR Emitter
• (2) 1-Meter Stereo Interconnect Cables
• (1) Leviton® Frame
LSWP S128P LOCAL SOURCE WALL PLATE KIT
ORDER NO. LSWP
CVRM COMPONENT VIDEO RECEIVE PLATE
SPECIFICATIONS
Input Imp.. . . . . . . . . 50 Ohms, (4.0V max)
Output Imp . . . 75 Ohms, 1V pk-pk (3.5V max)
Bandwidth: . . . . . 150MHz (125MHz@500 ft.)
THD . . . . . . . . . . . . . . . . . . . .-50dBc
Network Gain . . . . . . . . . . . . . . . . .1.0
Power. . . . . . . . . . . Supplied by Send Plate
Style . . . . . . . . . .White Decora
®
-style only
ORDER NO. CVRP
For use with the V85
Component Video Controller,
the CVRM provides an easy,
loss-free way to terminate
Cat-5 wire runs on the
back side and a component
video cable on the front. DIP
switches allow you to adjust
the video gain level and
contrast based on the length
of the Cat-5 wire run.
 FEATURES
For use with V85 Component Video Controller
 Easy connection of Cat-5 video wire run
& component video cable
 DIP-switch configurable for different wire
run lengths
 Single-gang, Decora
®
-styling
 Available in White
AUDIO/VIDEO WALL PLATES
CVWP
COMPONENT VIDEO WALL PLATE KIT
SPECIFICATIONS
Send Plate
Input Imp. . . 75 Ohms, 1V pk-pk (3.4V max)
Output Imp. . . . . . . . . . . . . . 50 Ohms
Bandwidth . . . . . . . . . . . 450MHz (-3dB)
Channel Separation . . . . . . . . . . . 90dB
Power . . . . . . . . . . . 16VDC, 1.5A (incl.)
Receive Plate
Input Imp. . . . . . . . . 50 Ohms, (4.0V max)
Output Imp. . . 75 Ohms, 1V pk-pk (3.5V max)
Bandwidth:. . . . 150MHz (125MHz@500 ft.)
THD . . . . . . . . . . . . . . . . . . -50dBc
Network Gain . . . . . . . . . . . . . . . 1.0
Power. . . . . . . . . . Supplied by Send Plate
Style . . . . . . . . . . .White Decora
®
-style only
ORDER NO. CVWP
The Component Video Wall Plate (CVWP) Kit ex-
tends high –and standard– definition component
video wire runs up to 500 ft. over Cat-5 cable. The
CVWP can be used in any system that requires
component video signals be sent over long
distances, and is the perfect mate to the S128P
Multi-Room A/V Controller.
The CVWP can also be used to distribute local
component video sources, such as DVD players
and satellite receivers, back to the head end for
house-wide distribution through a S128P or other
video switchers.
The CVWP Kit consists of 2 single-gang, Decora®-
style wall plates: a SEND plate and a RECEIVE
plate. DIP switches on the RECEIVE plate adjust
the video gain level and contrast based on wire run
length. Both plates also have F-to-F barrel connec-
tors for routing digital audio over coaxial cable.
 FEATURES
Send component video signals up to 500 ft.
w / o signal loss using Cat-5 cable
 Ideal for S128P component video distribution
 DIP-switch configurable for different wire run
lengths
 Digital coax audio connectors
 Single-gang, Decora
®
-styling