Specifications

©2011 ELAN HOME SYSTEMS • CARLSBAD, CA USA • ALL RIGHTS RESERVED
Lighting Control
44
Phase couplers are designed to enhance the communi-
cation reliability of the system.
They provide a path for a signal generated on one
phase, in a typical split-phase (single-phase) 240 VAC
residential system to cross over to the other phase
of the powerline. A PPC1 is recommended in each
breaker panel in a home. If a 220V 3- or 4-prong
receptacle is available use the PPC3 or PPC4.
In larger systems (homes over 5000 sq. ft) that have
more than 3 electrical panels signal attenuation is a
culprit that may reduce communication strength. The
main purpose of the SPR1 is to increase the powerline
communication reliability by taking the communica-
INSTALLATION & SUPPORT DEVICES
These items are designed to reduce/eliminate electri-
cal noise or the attenuating effects of devices that
could interfere with our communication signals. A
few different types of ballasts, power supplies, power
conditioners and motors can place unwanted noise on
the powerline; these chokes and filters ensure reliable
performance of your system. The ILC In-Line Choke is
used on wire-in devices rated for 120 VAC devices that
draw up to 1.8 Amps. The Plug-in 120 VAC PLF5 (3.8
A) and PLF15 (15A) filters plug in between the noisy
offender and isolates them from the electrical wiring.
The PLF15 has two outlets for plugging in multiple
devices or power strips.
LINE FILTERS
IN-LINE 1.8 AMP CHOKE FILTER ORDER NO. ILC
POWERLINE 3.8 AMP FILTER ORDER NO. PLF5
POWERLINE 15 AMP FILTER ORDER NO. PLF15
FEATURES
 Ensures reliable communication
 Blocks low frequency noise above 4 kHz
 Isolates attenuation effect of highly capacitive
devices
tions transmitted on one phase (leg) of the electrical
system and repeating them on to the other phase (leg)
at full strength.
For environments such as restaurants, apartment
complexes, office buildings or across multiple electri-
cal phases, the TPR120 is designed to deliver all the
benefits on three-phase 120/208VAC Delta-Wye 60Hz
power.
COUPLERS
2-WIRE 120/240VAC ORDER NO. PPC1
PLUG-IN 3 PRONG NEMA 10-30P ORDER NO. PPC3
PLUG-IN 4 PRONG NEMA 14-30P ORDER NO. PPC4
REPEATERS
SPLIT PHASE REPEATER ORDER NO. SPR1
THREE PHASE REPEATER ORDER NO. TPR120
The Lighting Control Panel provides ample room to
house up to ten WS1D24, fifteen WS1D15/ WS1D10,
or twenty WS1D6 dimmers controlling a maximum
of 20 individual circuits and delivering 24,000W or
18,000VA of power. A total of thirty three (½ X ¾
LIGHTING CONTROL PANEL
LIGHTING CONTROL PANEL ORDER NO. LCPU
combo type) knockouts are provided on the top, bot-
tom and back of the enclosure for simplified wiring.
The LCP is designed to be flush-mounted between
two16-inch center-to-center studs or surface-mounted
on any flat surface. De-rating is not needed as all the
heat generated by high-power lighting controls is
properly dissipated.
FEATURES
 The cost to design, layout, construct, wire, and
program a central-star system lighting system is
greatly reduced
 Hinged Interior panel can swing out for easy
access for wiring
 Door lock to prevent tampering13 knockouts
(½ x ¾ combo type) on both the top and the
bottom of the unit and 20 knockouts on the
rear, for simple wiring
 Advanced heat dissipation, de-rating is
not needed
ORDER NO. PIMR (FOR RS-232)
ORDER NO. PIMU (FOR USB)
The PIM plugs into any standard 120VAC electrical
outlet. The PIMR is an RS-232 serial interface that con-
nects to any available COM port via a DB9 serial cable
(included). The PIMU is a USB serial interface that
connects to any available USB port. Software drivers
allow the PIMU to emulate a serial PIM by taking over
an available COM port.
POWERLINE INTERFACE MODULES
COUPLERS & REPEATERS