Hitachi Gigabit Router GR2000 Series Enhanced Version Routing Software 06-02 (OS3) Installation Guide S-9181-31X
Routing Software 06-02 (OS3) Installation Guide Statement on EN55022 Compliance WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Statement on Federal Communications Commission (FCC) Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Trademarks Ethernet is a product name of Xerox Corp., USA. Ethernet is a trademark of Fuji Xerox Co., Ltd. MS-DOS® is a registered trademark of Microsoft, Corp. UNIX is a registered trademark, in the USA and other countries, licensed by X/Open Company Limited. NetWare is a registered trademark of Novell, Inc., USA. IPX is a registered trademark of Novell, Inc., USA. HP OpenView is a trademark of Hewlett-Packard Company, USA. Windows 95 is a trademark of Microsoft, Corp., USA.
Routing Software 06-02 (OS3) Installation Guide Change Record Revision No.
Abbreviations S-9181-31X AAL ATM Adaptation Layer ABR Available Bit Rate AFI Authority and Format Indicator AIS Alarm Indication Signal ANSI American National Standards Institute ARP Address Resolution Protocol AS Autonomous System ATM Asynchronous Transfer Mode BECN Backward Explicit Congestion Notification BGP Border Gateway Protocol BGP4 Border Gateway Protocol 4 BOD Bandwidth On Demand BPDU Bridge Protocol Data Unit CATV Cable Television CBR Constant Bit Rate CIDR Classl
Routing Software 06-02 (OS3) Installation Guide vi ERP Echo Response ERQ Echo Request ES End System FCS Frame Check Sequence FDB Filtering Data Base FDDI Fiber Distributed Data Interface FERF Far End Receive Failure HDLC High-level Data Link Control HNA Hitachi Network Architecture ICMP Internet Control Message Protocol IDI Initial Domain Identifier IEEE Institute of Electrical and Electronics Engineers, Inc.
S-9181-31X MMF Multi Mode Fiber MRU Maximum Receive Unit NSAP Network Service Access Point MTU Maximum Transfer Unit NBP Name Binding Protocol NCP Network Control Protocol NET Network Entity Title NetBIOS Network Basic Input/Output System NIF Network Interface board NRZ Non-Return-to-Zero NSAP Network Service Access Point OC-3c Optical Carrier level 3 concatenation OC-12c Optical Carrier level 12 concatenation OAM Operation Administration and Management OSI Open Systems Interco
Routing Software 06-02 (OS3) Installation Guide SD Start Delimiter SDH Synchronous Digital Hierarchy SDLC Service Advertising Protocol SD-I Super Digital I interface SFD Start Frame Delimiter SMF Single Mode Fiber SNA Systems Networking Architecture SNAP Sub-Network Access Protocol SNMP Simple Network Management Protocol SONET Synchronous Optical Network SPF Shortest Path First SPT Spanning Tree SPX Sequenced Packet Exchange SSAP Source Service Access Point SSP Switch to Switch
Table of Contents 1 Update and Installation Procedures..................................................................................................... 1 1.1 Notes When Updating and Installing .............................................................................................. 1 2 Updating Software ................................................................................................................................. 3 2.1 Update Procedure 1 ..........................................
Routing Software 06-02 (OS3) Installation Guide This page left intentionally blank x S-9181-31X
1 Update and Installation Procedures 1.1 Notes When Updating and Installing 1. While installing, do not pull out and insert an MC card, and do not turn off and on the GR2000. 2. Do not execute a ppupdate command in the multiple login condition. 3. Figure 1-1 shows a transfer of a file from a PC. Always use the binary mode when transferring files by the file transfer protocol (FTP). If the FTP fails, restart the FTP from the beginning.
Routing Software 06-02 (OS3) Installation Guide automatic restart. If the connection is broken, the ppupdate command does not terminate to fail in updating, and restoration of the GR2000 may be disabled. 10. If a message ",QYDOLG FRQWHQWV RI 83'$7( WJ]" is displayed while executing ppupdate command, follow the instructions below: Transfer the update file again to the user’s home directory, then execute command cmp ~/UPDATE.tgz /primaryMC/usr/var/update/UPDATE.tgz to compare files.
When the target of the update is S-9181-31X (ROUTE-OS3-X), Table 2-4 shows the available update versions, available MC capacity, and execution of the updating boot ROM on the CPU board. Note tha t 1K is equal to 1024 bytes. Table 2-4 Free MC Space Required for Updating No.
Routing Software 06-02 (OS3) Installation Guide 2.1 Update Procedure 1 This is an update procedure for a GR2000 that is configured from one RM using two MCs. It updates the backup and current MCs, both with an old version of software stored in them. After the update for the current MC is complete, the GR2000 automatically restarts. Upon restart, communication is interrupted temporarily. Do not pull out and insert an MC card while updating the software. 1.
2.2 Update Procedure 2 This update procedure is for a GR2000 configured from one RM using one MC. It updates the current MC card with an old version of software stored in it. After the updating procedure for the current MC is complete, the GR2000 automatically restarts. Upon restart, communication is interrupted temporarily. Do not pull out and insert an MC card while updating the software. 1. Log into a GR2000 with a user ID that the user has set (for example, RSHUDWRU). 2. Enter an admin command.
Routing Software 06-02 (OS3) Installation Guide 2.3 Update Procedure 3 This update procedure is for a GR2000 that is configured from two RMs, each using two MCs. It updates the backup and current MC cards, both with an old version of software stored in them for individual RMs of the active and standby systems. After the update procedure for the current MC is complete, the GR2000 automatically restarts. Upon restart, communication is interrupted temporarily.
2.4 Update Procedure 4 This is a version-up procedure for a GR2000 that is configured from two RMs, each using one MC. It updates the current MC card with an old version of software stored in it for individual RMs of the active and standby systems. After the updating procedure for the current MC in the RM of the active system is complete, the GR2000 automatically restarts up. Note that when it restarts up, communication is interrupted temporarily.
Routing Software 06-02 (OS3) Installation Guide 3 Installing Software When installing this program product in a new MC64, do it by the procedure described below using a backup slot. Table 3-1 lists the files used to install the software. Table 3-1 Files used for Installation No. Directory in CD-ROM Name of File 1 ALL BA62.tgz 1. Log into a GR2000 with an account that the user has set (for example, RSHUDWRU). 2. Execute a admin command to switch to the DGPLQ mode. 3.
