User Guide CC3-CAJUN • CompactPCI ® Low Power CPU Document No.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Contents About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Edition History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Guide CC3-CAJUN • Low Power CompactPCI CPU Technical Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Local PCI Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Local SMB Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GPIO Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Guide CC3-CAJUN • Low Power CompactPCI CPU About this Manual This manual describes the technical aspects of the CC3-CAJUN, required for installation and system integration. It is intended for the experienced user only. Edition History Document Text # 4015 cc3_uge.wpd Ed.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Related Documents For information about the CC6-ACID refer to the CC6 Technical Information Manual, available at http://www.ekf.de/c/ccpu/cc6/cc6.html. For information about the CC0-CHILLOUT refer to the CC0 Technical Information Manual, available at http://www/c/ccpu/cc6/cc6.html. For information regarding the CCY-RIO rear I/O transition module please read the CCY Technical Information Manual, available at http://www.ekf.de/c/ccpu/cc3/cc3_e.html.
User Guide CC3-CAJUN • Low Power CompactPCI CPU CC3-CAJUN Features Feature Summary Feature Summary CC3-CAJUN Form Factor Single size CompactPCI style Eurocard (160x100mm2), front panel width 4HP (20.3mm) Processor Designed for Intel® ULV Celeron® and LV Pentium® III Micro FC-BGA processors (Tualatin 0.13µ generation), maximum junction temperature 100°C, processor thermal design power classification: < < < < CC3-1: 400MHz ULV Celeron, 0.95V, 100MHz FSB, 256KB L2 cache, 3.4W typical 4.2W max.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Thermal Conditions Processor cooled down by passive heatsink, typical thermal resistance 13.8K/W (natural convection), 4.6K/W (forced airflow @ 200LFM). Custom specific heatsink solutions on request.
User Guide CC3-CAJUN • Low Power CompactPCI CPU CC3-CAJUN with DVI-I Video Output CC3-CAJUN with VGA Video Output -8EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 Hamm • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • info@ekf.de • www.ekf.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Short Description CC3-CAJUN Alternatively equipped with the Intel® series of ULV Celeron® or LV Pentium® III processors, the CC3-CAJUN is a versatile 4HP/3U (single size Eurocard) CompactPCI® CPU board, designed especially for systems which require very low power consumption.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Block Diagram CC3-CAJUN ULV Celeron 400/650MHz Block Diagram CC3-CAJUN LV Pentium 3 800/933MHz SDRAM 64-512MB PC100/133 Digital/Analog DVI-I 164 GMCH 82815 SO-DIMM 144 Video IDE I/F VGA D-SUB FSB 100/133MHz ICH2 82801 Compact FLASH ATA Opt.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Top View Component Assembly CC3-CAJUN PGPIO PIDE Compact Flash USB COM ETH P3 JRTC 82 551 ICH2 CPU RST 815 GMCH DVI-I or VGA JCOM PLPC 61 50 SO-DIMM PSPK JSWAP ©EKF CC3-CAJUN ekf.com - 11 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 Hamm • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • info@ekf.de • www.ekf.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Expansion Modules CC6-ACID & CC0-CHILLOUT Available optionally as a mezzanine companion board to the CC3-CAJUN, the CC6-ACID is provided with several legacy I/O ports in addition. This module can be mounted either to the bottom side or on top of the CC3-CAJUN and communicates across the LPC (Low Pin Count) interface. In addition, the CC6-ACID can be delivered with an on-board 2.5-inch Ultra ATA hard disk drive, resulting in a very compact system.
User Guide CC3-CAJUN • Low Power CompactPCI CPU CC6-ACID (4HP) CC6-ACID (8HP) - 13 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 Hamm • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • info@ekf.de • www.ekf.
LPC (Low Pin Count) Super I/O LPCT (Top Mounting) LPCB (Bottom Mounting) FDD P12 CC2 CC5 CC7 CC8 FDD P4/5 LPC P1 User Guide CC3-CAJUN • Low Power CompactPCI CPU 34 26 P10 external Floppy-Disk FD FAN P6-P9 IRDA KB/MS Game GPIO LPT J1 Spkr ADM 811 COM1 RS-232E SD Block Diagram CC0-CHILLOUT SD J-SER1 Option © EKF SER1 Option ADM 811 Rear I/O J2 MIDI P11 TTL COM2 RS-232E SER2 TTL USB1 J-SER2 USB1 CC2 CC5 CC7 Option 40 IDE1 EN 44 IDE2 Optional On-Board Ultra ATA 2.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Rear I/O Transition Module CCY-RIO The CCY-RIO transition module provides a 4HP back panel with connectors for PS/2 style keyboard and mouse, a serial RS-232E COM port, and an USB receptacle. Rear I/O requires that a suitable J2 backplane is present in your CompactPCI system. By default, the CC3-CAJUN is equipped with line terminating resistors for a common 64-bit CPCI J2 backplane.
User Guide CC3-CAJUN • Low Power CompactPCI CPU photo CC3-CAJUN & CCY-RIO soon here CCY-RIO - 16 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 Hamm • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • info@ekf.de • www.ekf.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Rear I/O Transition Module CCZ-RIO Available as an option, the CC3-CAJUN can be combined with the CC0-CHILLOUT companion board, which has been designed mainly for rear I/O systems. Therefore the CCZ-RIO is required in addition for passing signals across a single slot rear I/O backplane to the rear panel.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Strapping Headers ISPCON In System Programmable GAL (PLD programming), not stuffed JCOM Local RS-232 transceiver enable, option JRTC CMOS and RTC reset PGPIO Local GPIO signals derived from the on-board SIO, option PSPK Speaker connector, option Connectors & Sockets CFA CompactFlash ATA socket (secondary IDE interface) J1/J2 CompactPCI Bus, PXI, Rear I/O JSWAP Signal from the board ejector lever switch, used for reset if dedicated push-button is
User Guide CC3-CAJUN • Low Power CompactPCI CPU Microprocessor The CC3-CAJUN supports the 0.13µ Ultra Low-Voltage (ULV) Celeron® and Low-Voltage (LV) Pentium®-III processors as listed below. The processors are housed in a Micro FC-BGA package for direct soldering to the PCB, i.e. the CPU chip cannot be removed or changed by the user. Do not confuse the processor host bus frequency (FSB front side bus or PSB processor side bus) with the memory speed or the PCI clock, which are independent from each other.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Thermal Considerations In order to avoid malfunctioning of the CC3-CAJUN, take care of appropriate cooling of the processor and system, e.g. by a cooling fan suitable to the maximum power consumption of the CPU chip actually in use. Please note, that the processors temperature is steadily measured by a special controller (MAX1617), attached to the onboard SMBus® (System Management Bus).
User Guide CC3-CAJUN • Low Power CompactPCI CPU The forced airflow thermal resistance of the snap-on heatsink is 4.6K/W @ 200lfm, 2.7K/W @ 400lfm and 2.0K/W @ 600lfm. With no forced airflow (natural convection) the heat sink thermal resistance is ~13.8K/W. With 100°C as maximum specified die temperature, the worst case ambient temperatures for the CC3-CAJUN can be calculated a follows: Maximum Permissible Ambient Temperature Processor Max. Power 0 LFM 200 LFM 400 LFM 600 LFM ULV Celeron 400MHz 4.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Main Memory The CC3-CAJUN is equipped with a socket for installing a single 144-pin SO-DIMM module. Minimum common memory size is 128MB; maximum memory size is 512MB. Due to the video requirements of the i815 chipset, the recommended minimum memory for the Windows 2000 and Windows XP operating systems is 256MB (some of the system memory is dedicated to the graphics controller). The supported on-board memory is entirely chacheable.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Enhanced IDE / ATA Interface The EIDE interface (also referenced as ATA or PATA = Parallel ATA) is responsible for the exchange of information between the processor and peripheral mass storage devices such as hard disks, ATA CompactFlash cards and optical drives.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Graphics Subsystem The graphics subsystem is part of the Intel 82815 Graphics/Memory Controller Hub (GMCH), supporting the following features: C C C C C C C C 3-D Hyper Pipelined architecture Full 2-D hardware acceleration Motion video acceleration 3-D graphics visual and texturing enhancements Integrated 24-bit 230MHz RAMDAC DDC2B compliant Hardware motion compensation for software MPEG2 decode Integrated graphics memory controller The CC3-CAJUN is provided
User Guide CC3-CAJUN • Low Power CompactPCI CPU As a stuffing option, the CC3-CAJUN can be equipped with an ordinary HD D-Sub 15-lead female connector (VGA style). This connector is suitable for analog signals only, so the PanelLink transmitter is not stuffed with this option. Nevertheless also most flat-panel displays can be attached to the D-Sub connector with only minor impact on the image quality. Independent from the video connector actually in use, DVI or VGA, the VESA DDC 2B standard is supported.
User Guide CC3-CAJUN • Low Power CompactPCI CPU LPC Super- I/O Interface In a modern system, legacy ports as PS/2 keyboard/mouse, COM1/2 and LPT have been replaced by USB and Ethernet connectivity. The 1.4MB floppy disk drive has been overcome by CD-RW or DVD-RW optical drives, attached to the IDE connector, or USB memory sticks. Hence, the CC3CAJUN is virtually provided with all necessary I/O ports.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Watchdog/Reset The CC3-CAJUN is provided with two MAX6705 supervisor circuits, which monitor the supply voltages 3.3V and 5V, and generate a power-on reset signal. The manual push-button reset is also passed through the MAX6705s for appropriate pulse conditioning. The reset push-button (if present) is situated at the front panel. The button is indent mounted behind the front and requires a tool, e.g.
User Guide CC3-CAJUN • Low Power CompactPCI CPU ATA (Hard Disk Activity) LED The CC3-CAJUN is provided with a software programmable LED in the front panel, labeled as ATA. After system reset, this LED defaults to signal the ATA/IDE activity. By the first setting of the GPO22 of the ICH2 82801 this LED changes its function and is then controlled only by the level of the GPO22 pin. Setting this output to 1 will switch on the LED. The LED IDE remains in the programmable state until the next system reset.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Local GPIO Option In addition to the GPIO / PXI-Trigger lines optionally available on J2, the optional pin-header PGPIO provides another two GPIO lines available for user specific application. The 5V level TTL signals sio_gpio16/17 are controlled by the on-board SIO IT8761E, with an internal 50k PU resistor and capable of sinking 24mA each. - 29 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 Hamm • Germany Tel. +49 (0)2381/6890-0 • Fax.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Rear I/O Options Optionally, the CC3-CAJUN can be used for rear I/O with respect to the following functions: • • • • • Primary IDE USB Port 2 Keyboard, Mouse COM1 (TTL Level) GPIOs If attachment of IDE devices across the rear I/O path is chosen, the CC3-CAJUN on-board IDE connector must be removed or at least left unused, in order to avoid a T-connection.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Installing and Replacing Components Before You Begin Warnings The procedures in this chapter assume familiarity with the general terminology associated with industrial electronics and with safety practices and regulatory compliance required for using and modifying electronic equipment.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Installing the Board Warning This procedure should be done only by qualified technical personnel. Disconnect the system from its power source before doing the procedures described here. Failure to disconnect power, or telecommunication links before you open the system or perform any procedures can result in personal injury or equipment damage.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Removing the Board Warning This procedure should be done only by qualified technical personnel. Disconnect the system from its power source before doing the procedures described here. Failure to disconnect power, or telecommunication links before you open the system or perform any procedures can result in personal injury or equipment damage.
User Guide CC3-CAJUN • Low Power CompactPCI CPU EMC Recommendations In order to comply with the CE regulations for EMC, it is mandatory to observe the following rules: C The chassis or rack including other boards in use must comply entirely with CE C Close all board slots not in use with a blind front panel C Front panels must be fastened by built-in screws C Cover any unused front panel mounted connector with a shielding cap C External communications cable assemblies must be shielded (shield conne
User Guide CC3-CAJUN • Low Power CompactPCI CPU Installing or Replacing the Memory Module Note: If you decide to replace the memory, observe the precautions in 'Before You Begin' By default, the CC3-CAJUN comes fully equipped and tested with a 256MB/512MB SD-RAM memory module. So normally there should be no need to install a memory module. The CC3-CAJUN requires a PC-133 (133MHz) SDRAM SO-DIMM module independent from the processor front side bus (100MHz ULV Celeron, 133MHz LV Pentium III).
User Guide CC3-CAJUN • Low Power CompactPCI CPU Technical Reference Local PCI Devices The following table shows the on-board PCI devices and their location within the PCI configuration space. These devices consist of the Ethernet controller, the PCI-To-PCI Bridge and several devices within the i815 chip set.
User Guide CC3-CAJUN • Low Power CompactPCI CPU GPIO Usage GPIO Usage ICH2 CC3-CAJUN GPIO Usage ICH2 Function CC3 Features Origin/Destination p2_fal# GPI 0 ICH2 I (5V tol.) CPCI Power Mgmt. p2_deg# GPI 1 ICH2 I (5V tol.) CPCI Power Mgmt. pirqe# GPI 2 ICH2 I LAN NC1 pirqf# GPI 3 ICH2 (5V tol.) CPCI INTC# pirqg# GPI 4 ICH2 (5V tol.) CPCI INTD# pirqh# GPI 5 ICH2 I ICH2 USB2 p1_enum# GPI 6 ICH2 I (5V tol.) CPCI - GPI 7 ICH2 I (5V tol.
User Guide CC3-CAJUN • Low Power CompactPCI CPU GPIO Usage FWH CC3-CAJUN GPIO Usage FWH Function FWH Features Origin/Destination FWH1/FWH2 Identity GPI 0 FWH I (3.3V) GND = FWH1 3.3V = FWH2 p66detect (IDE) GPI 1 FWH I (3.3V) IDE I/F wdogrst GPI 2 FWH I (3.3V) ispGAL MSB Board Revision GPI 3 FWH I (3.3V) LSB Board Revision GPI 4 FWH I (3.3V) GPI3 GPI4 Rev.
User Guide CC3-CAJUN • Low Power CompactPCI CPU GPIO Usage PCI Bridge CC3-CAJUN GPIO Usage PCI-PCI Bridge PLX 6150 Function 2050 Features Origin/Destination p2_sysen# GPIO 0 I/O (5V tol.) CPCI enintp GPIO 1 I/O (5V tol.) ispGAL enints GPIO 2 I/O (5V tol.) ispGAL enserirq GPIO 3 / HSSWITCH# I/O (5V tol.) CPCI, ispGAL - 39 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 Hamm • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • info@ekf.de • www.ekf.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Front Panel Connectors CC3CAJUN CC3CAJUN USB COM ekf.com USB G P COM © EKF G P A T A A T A ETH D V I ETH draft only - do not scale P o w RES V G A CC3-CAJUN DVI/VGA - 40 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 Hamm • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • info@ekf.de • www.ekf.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Video Monitor Connector DVI-I DVI-I 17 1 9 16 24 TX0- 9 TX1- 1 TX2- 18 TX0+ 10 TX1+ 2 TX2+ 19 GND 11 GND 3 GND 20 12 4 21 13 5 22 GND 14 DDC_POW 1) 6 DDC_SCL 23 TXC+ 15 GND 7 DDC_SDA 24 TXC- 16 DVI_HP 8 VSYNC 8 c3 c1 c4 c2 c6 1) 17 c5 +5V protected by a PolySwitch Fuse 0.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Video Monitor Connector HD-DSUB (Option) As an option, the CC3-CAJUN can be equipped with a legacy VGA connector (High-Density DSub 15-position female connector). The VGA connector replaces the DVI-I receptacle, and the digital video interface therefore is not available with this option. VGA (Option - Replaces DVI-I) 10 5 15 11 1 6 1) +5V protoected by a PolySwitch Fuse 0.
User Guide CC3-CAJUN • Low Power CompactPCI CPU USB Connector USB Port 1 1) 4 +5V protected by an Electronic Fuse 0.5A 1 POW 1) 2 USB DATA NEG 3 USB DATA POS 4 GND Ethernet Connector Fast Ethernet RJ45 Jack 270.01.08.1 1 8 1 TX+ 2 TX- 3 RX+ 4 5 Upper green LED: on=link established blinking=activity (data) Lower yellow LED: on=100Mbit/s off=10Mbit/s 6 RX- 7 8 The yellow LED signals 100Mbit/s when lit, and 10Mbit/s when off.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Serial I/F Connector RS-232 RS-232 (COM Port) RJ45 Jack 270.00.08.1 1 8 red = input blue = output 1 DSR 2 DCD 3 DTR 4 GND 5 RXD 6 TXD 7 CTS 8 RTS In order to make use of the RS-232 front panel jack, the on-board RS-232E transceiver must be enabled (install jumper J-COM). Adapters or adapter cable assemblies may be used to emulate a PC style COM port.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Due to the limitation in its number of lead positions, the CC3-CAJUN RS-232 RJ45 connector is not provided with the Ring Indicator (RI) signal, which may be in use with POTS modems. A solution to this issue would be the CC6-ACID mezzanine companion board, which provides two PC style COM port connectors in its front panel, including RI. 1 © EKF ekf.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Internal Connectors Caution Some of the internal connectors and jumpers may provide operating voltage (e.g. +3.3V, +5V and +12V) to devices inside the system chassis, such as fans and internal peripherals. Not all of these connectors are overcurrent protected. Do not use these internal connectors for powering devices external to the computer chassis.
User Guide CC3-CAJUN • Low Power CompactPCI CPU LPC Low Pin Count Socket PLPC PLPCT/PLPCB 2 276.53.026.01 1 26 1.27mm Socket GND 1 2 pciclk GND 3 4 lad0 GND 5 6 lad1 GND 7 8 lad2 GND 9 10 lad3 GND 11 12 lframe# GND 13 14 ldrq# serirq 15 16 lpme# lsmi# 17 18 pcirst# 5V 19 20 3.3V rcin# 21 22 a20gate 12V 23 24 3.
User Guide CC3-CAJUN • Low Power CompactPCI CPU ATA/IDE Header PIDE 1 241.2.0220.10.09 2 Key 39 40 2.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Local GPIO Header (Option) PGPIO 1 2 3 GND sio_gpio16 sio_gpio17 1 Both GPIO signals are 5V TTL with internal 50k PU resistors, 24mA sink capability, controlled by the on-board SIO IT8761E. Speaker Header (Option) JSPK 1 2 +5V Speaker 1 Warning: The +5V pin is protected against a short circuit situation by a 0.1A PolySwitch. The JSPK connector should be used exclusively for direct attachment of a dynamic speaker device.
User Guide CC3-CAJUN • Low Power CompactPCI CPU RS-232 Transceiver Enable Jumper (Option) JCOM 1 2 ENABLE# GND 1 If stuffed, the jumper JCOM may be used to enable/disable the local RS-232E transceiver. Installing the jumper enables the transceiver, removing the jumper shuts down the transceiver. Be sure not to enable both, the CC3-CAJUN local transceiver, and the CCY-RIO rear I/O transceiver, in order to avoid signal interference. PLD Programming Header ISPCON 1 1 2 3 4 5 6 7 8 +3.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Processor Debug Header JITP itpres# 2 1 GND dbreset# 4 3 GND tck 6 5 GND tms 8 7 tdi itppon 10 9 tdo 12 11 trst# GND 14 13 GND 16 15 itpreq# GND 18 17 itprdy# GND 20 19 GND 22 21 GND 24 23 GND 26 25 GND 28 27 GND 30 29 Note: The Debug Header is not normally stuffed. Its footprint is situated at the bottom side of the board. - 51 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 Hamm • Germany Tel.
User Guide CC3-CAJUN • Low Power CompactPCI CPU CompactPCI J1/J2 f e d c b a 25 f e d c b a J2 2mm Metric Connector J1 2mm Hard Metric Connector 22 1 1 - 52 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 Hamm • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • info@ekf.de • www.ekf.
User Guide CC3-CAJUN • Low Power CompactPCI CPU #J1 A B C D E 25 5V REQ64# ENUM# 3.3V 5V 24 AD1 5V VI/O AD0 ACK64# 23 3.3V AD4 AD3 5V AD2 22 AD7 GND 3.3V AD6 AD5 21 3.3V AD9 AD8 M66EN (GND) C/BE0# 20 AD12 GND VI/O AD11 AD10 19 3.3V AD15 AD14 GND AD13 18 SERR# GND 3.3V PAR C/BE1# 17 3.3V IPMB SCL IPMB SDA GND PERR# 16 DEVSEL# GND VI/O STOP# LOCK# 15 3.3V FRAME# IRDY# GND TRDY# 11 AD18 AD17 AD16 GND C/BE2# 10 AD21 GND 3.
User Guide CC3-CAJUN • Low Power CompactPCI CPU #J2 A B C D E 22 GA4 GA3 GA2 GA1 GA0 21 CLK6 GND RSV KB_DAT RSV KB/MS_POW RSV MS_DAT 20 CLK5 GND RSV KB_CLK GND RSV MS_CLK 19 GND GND RSV COM1_TXD RSV COM1_RXD RSV COM1_RTS# 18 BRSVP2A18 BRSVP2B18 BRSVP2C18 GND BRSVP2E18 PXI_TRIG6 17 BRSVP2A17 GND PRST# REQ6# GNT6# 16 BRSVP2A16 PXI_TRIG1 BRSVP2B16 PXI_TRIG0 DEG# GND BRSVP2E16 PXI_TRIG7 15 BRSVP2A15 MOD_DET# GND FAL# REQ5# GNT5# 14 AD35 IDE_RST# AD34 IDE_D
User Guide CC3-CAJUN • Low Power CompactPCI CPU Power Connector P3 (Option) P3 (Option) 1 +5V 2 +5V 3 GND 4 GND 5 GND 6 GND 7 +3.3V 8 +3.3V This connector is optional for stand-alone operation of the CC3-CAJUN (not normally stuffed). It is a 2.50mm pitch eight position pin header, AMP Tyco EI series part no. 171825-8. Refer to the Tyco website for suitable matching components. If P3 is in use for power supply, J1/J2 are not needed for stand-alone operation.
User Guide CC3-CAJUN • Low Power CompactPCI CPU Literature Theme Document Title Origin CompactPCI CompactPCI Specification, PICMG 2.0 R3.0, Oct. 1, 1999 PICMG (http://www.picmg.org) USB Universal Serial Bus Specification http://www.usb.org/developers/docs/ CompactFlash CF+and CompactFlash Specification Revision 2.0 CompactFlash Association www.compactflash.org EKF Elektronik GmbH Philipp-Reis-Str. 4 59065 HAMM Germany Fax. +49 (0)2381/6890-90 Tel. +49 (0)2381/6890-0 Internet www.ekf.
